Home › ENGINE · 2TR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P2431    Secondary Air Injection System Air Flow / Pressure Sensor Circuit Range / Performance Bank1

DTC    P2432    Secondary Air Injection System Air Flow / Pressure Sensor Circuit Low Bank1

DTC    P2433    Secondary Air Injection System Air Flow / Pressure Sensor Circuit High Bank1

for Preparation Click here


DESCRIPTION

The secondary air injection system consists of an air pump assembly, the air switching valve assembly, an air pressure sensor, the air injection control driver and the ECM. For a short time after cold engine starts, the secondary air injection system pumps secondary air to the exhaust port of the cylinder head to purify the exhaust emissions. The secondary air is supplied by the air pump assembly and is pumped to the exhaust port through the air switching valve assembly.
The air injection control driver drives the air switching valve assembly and the air pump assembly according to command signals transmitted by the ECM. The air pressure sensor detects the pressure in the secondary air passage when the secondary air injection system is ON and OFF, and transmits pressure signal to the ECM.
The air injection control driver is not only equipped to drive the pump and valve, but also with a diagnosis function to detect malfunctions in the secondary air injection system circuit.

HINT:
As a large current is required to drive the air pump assembly and air switching valve assembly, an air injection control driver is included in this system.


A121746E09


DTC No.
DTC Detection Condition
Trouble Area
P2431
Air pressure sensor indicates less than 45.63 kPa (342 mmHg), or more than 135 kPa (1013 mmHg) (2 trip detection logic)
  1. Air pressure sensor
  2. Open or short in air pressure sensor circuit
  3. ECM
P2432
While engine running, voltage output of air pressure sensor remains below 0.5 V (1 trip detection logic)
  1. Air pressure sensor
  2. Open or short in air pressure sensor circuit
  3. ECM
P2433
While engine running, voltage output of air pressure sensor remains above 4.5 V (1 trip detection logic)
  1. Air pressure sensor
  2. Open or short in air pressure sensor circuit
  3. ECM

MONITOR DESCRIPTION

A085160E17
The ECM monitors the pressure in the secondary air passage using the air pressure sensor located on the air switching valve assembly in the secondary air injection system.
If there is a defect in the sensor or the sensor circuit, the voltage level deviates from the normal operating range, the ECM interprets this deviation as a malfunction in the air pressure sensor or circuit and stores a DTC.

MONITOR STRATEGY


Related DTCs
P2431: Air Flow/Pressure Sensor Circuit Rationality
P2432: Air Flow/Pressure Sensor Circuit Range Check (Low Voltage)
P2433: Air Flow/Pressure Sensor Circuit Range Check (High Voltage)
Required Sensors/Components (Main)
Air pressure sensor
Required Sensors/Components (Related)
-
Frequency of Operation
Continuous
Duration
P2432 and P2433: 0.5 seconds
P2431: 5 seconds
MIL Operation
P2432 and P2433: Immediate
P2431: 2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


P2431: 
Monitor runs whenever following DTCs not present
None
Secondary air injection system pressure sensor circuit fail (P2342, P2433)
Not detected
Starter
OFF
Battery voltage
8 V or more
Ignition switch
ON
Time after starter ON to OFF
2 seconds or more

P2432 and P2433: 
Monitor runs whenever following DTCs not present
None
Starter
OFF
Battery voltage
8 V or more
Ignition switch
ON

TYPICAL MALFUNCTION THRESHOLDS


P2431: 
Secondary air injection system Pressure
Less than 45.63 kPa (342 mmHg), or more than 135 kPa (1013 mmHg)

P2432: 
Air pressure sensor voltage
Less than 0.5 V

P2433: 
Secondary air injection system pressure sensor voltage
More than 4.5 V

COMPONENT OPERATING RANGE


Secondary air injection system pressure sensor voltage
Between 0.5 V and 4.5 V

CONFIRMATION DRIVING PATTERN

NOTICE:
  1. This Secondary Air Injection Check only allows technicians to operate the secondary air injection system for a maximum of 5 seconds.
    Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks.
    While secondary air injection system operation using the Techstream is prohibited, the Techstream display indicates the prohibition (WAIT or ERROR).
    If ERROR is displayed on the Techstream during the test, stop the engine for 10 minutes, and then try again.
  2. Performing the Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If necessary, leave an interval of several minutes between System Check operations to prevent the system from overheating.
  3. When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
  4. Turn the ignition switch off when the Secondary Air Injection Check operation finishes.

  1. Start the engine and warm it up.
  2. Turn the ignition switch off.
  3. Connect the Techstream to the DLC3.
  4. Turn the ignition switch to ON.
  5. Turn the Techstream on.
  6. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation) (Click here).
  7. Turn the ignition switch off and wait for at least 30 seconds.
  8. Turn the ignition switch to ON and turn the Techstream on.
  9. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.
  10. Start the engine after the Techstream initialization is finished.
  11. Perform the System Check operation by pressing Next.
  12. Perform the following to confirm the secondary air injection system pending DTCs: Press the Exit.
  13. Check for pending DTCs.

    OK:
    No pending DTC is output.

  14. After the "Air injection check" is completed, check for All Readiness by entering the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  15. Input the DTC: P2431, P2432 or P2433.
  16. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.

  17. If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.

  18. Turn the ignition switch off.

WIRING DIAGRAM


A237375E02


INSPECTION PROCEDURE

HINT:
  1. Refer to "Data List / Active Test" [Air Pump Pressure (Absolute)] (Click here).
  2. Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK HARNESS AND CONNECTOR (AIR PRESSURE SENSOR - ECM)
  1. Disconnect the air pressure sensor connector.

  1. Disconnect the ECM connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    A8-1 (E2) - E4-28 (E2)
    Always
    Below 1 Ω
    A8-2 (AIP) - E5-22 (AIP)
    Always
    Below 1 Ω
    A8-3 (VC) - E4-18 (VC)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    A8-2 (AIP) or E5-22 (AIP) - Body ground
    Always
    10 kΩ or higher
    A8-3 (VC) or E4-18 (VC) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT ECM (SENSOR POWER SOURCE CIRCUIT)
A065741E73
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E4-28 (E2) - Body ground
    Always
    Below 1 Ω

  1. Turn the ignition switch ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E4-18 (VC) - Body ground
    Ignition switch ON
    4.5 to 5.5 V

    Text in Illustration 
    *a
    Component with harness connected
    (ECM)



NG
REPLACE ECM (Click here)
OK


3.INSPECT AIR PRESSURE SENSOR
G034995E03
  1. Connect a pressure gauge to the air air pressure sensor as shown in the illustration.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Air pump pressure (absolute).

  1. Check that the pressure displayed on the Techstream fluctuates when applying the pressure to the air pressure sensor with the pressure gauge.
    Text in Illustration 
    *1
    Pressure Gauge
    *2
    Air Pressure Sensor

    OK:
    Pressure fluctuates in response to pressure applied with pressure gauge.

    HINT:
    The Techstream displays the air pump pressure (Air pump pressure (absolute)) as absolute pressure.



NG
REPLACE AIR PRESSURE SENSOR
OK

REPLACE ECM (Click here)