DTC P2431 Secondary Air Injection System Air Flow / Pressure Sensor Circuit Range / Performance Bank1 |
DTC P2432 Secondary Air Injection System Air Flow / Pressure Sensor Circuit Low Bank1 |
DTC P2433 Secondary Air Injection System Air Flow / Pressure Sensor Circuit High Bank1 |
DTC P2436 Secondary Air Injection System Air Flow / Pressure Sensor Circuit Range / Performance Bank 2 |
DTC P2437 Secondary Air Injection System Air Flow / Pressure Sensor Circuit Low Bank 2 |
DTC P2438 Secondary Air Injection System Air Flow / Pressure Sensor Circuit High Bank 2 |
| DTC No. | DTC Detection Condition | Trouble Area |
| P2431 P2436 | Pressure sensor indicates a value below 45.63 kPa (342 mmHg), or higher than 135 kPa (1013 mmHg) (2 trip detection logic). |
|
| P2432 P2437 | While the engine is running, the voltage output of the pressure sensor is below 0.5 V (1 trip detection logic). |
|
| P2433 P2438 | While the engine is running, the voltage output of the pressure sensor is higher than 4.5 V (1 trip detection logic). |
|

| Related DTCs | P2431: Air flow/Pressure sensor circuit rationality (bank 1) P2432: Air flow/Pressure sensor circuit range check (Low voltage) (bank 1) P2433: Air flow/Pressure sensor circuit range check (High voltage) (bank 1) P2436: Air flow/Pressure sensor circuit rationality (bank 2) P2437: Air flow/Pressure sensor circuit range check (Low voltage) (bank 2) P2438: Air flow/Pressure sensor circuit range check (High voltage) (bank 2) |
| Required Sensors/Components (Main) | Pressure sensor |
| Required Sensors/Components (Related) | - |
| Frequency of Operation | Continuous |
| Duration | P2432, P2433, P2437, P2438: 0.5 seconds P2431, P2436: 5 seconds |
| MIL Operation | P2432, P2433, P2437, P2438: Immediate P2431, P2436: 2 driving cycles |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not stored | None |
| All of the following conditions are met | - |
| Starter | OFF |
| Battery voltage | 8 V or higher |
| Ignition switch | ON |
| Secondary air injection system pressure sensor circuit fail (P2432, P2433, P2437, P2438) | Not detected |
| All of the following conditions are met | - |
| Starter | OFF |
| Battery voltage | 8 V or higher |
| Ignition switch | ON |
| Secondary air injection system pressure | Below 45.63 kPa (342 mmHg), or higher than 135 kPa (1013 mmHg) |
| Secondary air injection system pressure sensor voltage | Below 0.5 V |
| Secondary air injection system pressure sensor voltage | Higher than 4.5 V |
| Secondary air injection system pressure | 45.63 to 135 kPa (342 to 1013 mmHg) |
| Secondary air injection system pressure sensor voltage | Between 0.5 V and 4.5 V |
| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| 1.CHECK HARNESS AND CONNECTOR (AIR SWITCH VALVE ASSEMBLY - ECM) |
Disconnect the air switching valve assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A32-3 (AIP) - E13-1 (AIP) | Always | Below 1 Ω |
| A32-2 (VC) - E9-16 (VCV2) | Always | Below 1 Ω |
| A32-4 (E2) - E10-8 (ETHW) | Always | Below 1 Ω |
| A31-3 (AIP2) - E13-2 (AIP2) | Always | Below 1 Ω |
| A31-2 (VC2) - E9-16 (VCV2) | Always | Below 1 Ω |
| A31-4 (E22) - E10-8 (ETHW) | Always | Below 1 Ω |
| A32-3 (AIP) or E13-1 (AIP) - Body ground | Always | 10 kΩ or higher |
| A32-2 (VC) or E9-16 (VCV2) - Body ground | Always | 10 kΩ or higher |
| A31-3 (AIP2) or E13-1 (AIP2) - Body ground | Always | 10 kΩ or higher |
| A31-2 (VC2) or E9-16 (VCV2) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 2.CHECK TERMINAL VOLTAGE (VC OF AIR SWITCHING VALVE) |
![]() |
Disconnect the air switching valve connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A32-2 (VC) - A32-4 (E2) | Ignition switch ON | 4.5 to 5.5 V |
| A31-2 (VC2) - A31-4 (E22) | Ignition switch ON | 4.5 to 5.5 V |
| *a | Front view of wire harness connector (to Air Switching Valve) |
| *b | Bank 1 |
| *c | Bank 2 |
|
| ||||
| OK | |
| 3.REPLACE AIR SWITCHING VALVE ASSEMBLY |
Replace the air switching valve assembly (Click here).
| NEXT | |
| 4.CHECK WHETHER DTC OUTPUT RECURS |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for 30 seconds.
Turn the ignition switch to ON and turn the Techstream on.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P2431, P2432, P2433, P2436, P2437 or P2438.
Check the DTC judgment result.
| Result | Proceed to |
| NORMAL (DTC is not output) | A |
| ABNORMAL (DTC P2431, P2432, P2433, P2436, P2437 or P2438 output) | B |
|
| ||||
| A | ||
| ||