Home › ENGINE ยท 2TR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P1500    AC Inverter Malfunction

for Preparation Click here


DESCRIPTION

This vehicle is equipped with a voltage inverter, which supplies power to various electrical appliances. When the main switch of the voltage inverter is turned ON, the inverter relay turns ON, and the inverter then converts the 12 V Direct Current (DC) of the battery into a 115 V Alternating Current (AC). The voltage inverter can output a maximum of 400 W from an outlet.
When the AC 115 V is output, a load is applied to the engine. The ECM controls the engine idling speed according to the vehicle speed and engine load. A speed signal is input to the inverter and an idle-up signal is transmitted to the ECM.

A182231E02


DTC No.
DTC Detection Condition
Trouble Area
P1500
While vehicle running, idling-up signal input into ECM for 10 seconds
  1. Open in speed signal circuit
  2. Short between idle-up signal and +B circuits
  3. Voltage inverter
  4. ECM

MONITOR DESCRIPTION

While the engine is idling, the ECM performs idle up according to the power supply of the inverter to stabilize the engine idling speed.
When the vehicle is stationary and the inverter input exceeds 8.3 A, the inverter sends an idle-up signal from the OUT terminal of the inverter to the ELS2 terminal of the ECM.
If the idle-up signal is input into the ECM for 10 seconds while the vehicle is running, the ECM interprets this as a malfunction in the inverter circuit and stores the DTC.

MONITOR STRATEGY


Related DTCs
P1500: Voltage Inverter Performance
Required Sensors/Components (Main)
Voltage inverter
Required Sensors/Components (Related)
-
Frequency of Operation
Continuous
Duration
10 seconds
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not present
None
Vehicle speed
5.0 km/h (3.11 mph) or more
Battery voltage
8 V or more
Ignition switch
ON
Starter
OFF

TYPICAL MALFUNCTION THRESHOLDS


Electric load signal 2
ON

CONFIRMATION DRIVING PATTERN


A218134E01

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on.
  6. Start the engine and warm it up until the engine coolant temperature reaches 70°C (158°F) or higher [A].
  7. Drive the vehicle for 30 seconds or more [B].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  8. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].
  9. Read the Pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  10. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  11. Input the DTC: P1500.
  12. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [B] and [C] again.

  13. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM


A239098E03


INSPECTION PROCEDURE

Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P1500)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.
    Result 
    Result
    Proceed to
    P1500 output
    A
    P1500 and other DTCs output
    B
    If any DTCs other than P1500 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.INSPECT VOLTAGE INVERTER (SPD SIGNAL)
A113678E02
  1. Move the shift lever to the neutral position.

  1. Jack up the vehicle.

  1. Turn the ignition switch to ON.

  1. Check the voltage between the terminals of the ECM connectors as the wheel is turned slowly.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E7-8 (SPD) - E4-3 (E1)
    Ignition switch ON
    Wheel turned slowly
    Voltage generated intermittently

    HINT:
    The output voltage should fluctuate up and down similarly to the diagram on the left when the wheel is turned slowly.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT ECM (ELS VOLTAGE)
G035001E05
  1. Disconnect the V8 inverter connector.

  1. Start the engine.

  1. Measure the voltage between the OUT terminal of inverter and the body ground.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    V8-9 (OUT) - Body ground
    Idling
    1 V or less



NG
Go to step 4
OK

REPLACE VOLTAGE INVERTER (Click here)  

4.CHECK HARNESS AND CONNECTOR (ECM - INVERTER, INVERTER - POWER SOURCE)
A113679E03
  1. Disconnect the V8 inverter connector.

  1. Disconnect the E7 ECM connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage between the terminals of the wire harness and body ground.

    Standard Voltage (Check for short in idling up signal circuit):
    Tester Connection
    Switch Condition
    Specified Condition
    V8-9 (OUT) or E7-20 (ELS2) - Body ground
    Ignition switch ON
    1 V or less



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)