ENGINE ASSEMBLY > REMOVAL |
| 1. DISCHARGE FUEL SYSTEM PRESSURE |
| 2. REMOVE BATTERY |
| 3. DRAIN ENGINE COOLANT |
![]() |
Remove the service hole cover from the engine under cover.
Install a vinyl hose onto the drain on the radiator side.
Fix the vinyl hose with tape.
![]() |
Loosen the 3 drain plugs on the engine and radiator, and drain the coolant.
Remove the radiator cap.
Drain the coolant from the reservoir tank.
Tighten the 3 drain plugs.
Remove the vinyl hose from the radiator.
| 4. DRAIN ENGINE OIL |
Remove the engine under cover seal No. 3.
Remove the oil pan drain plug and drain the engine oil.
Clean the oil pan drain plug and install it with a new gasket.
| 5. REMOVE HOOD SUB-ASSEMBLY |
Disconnect the windshield washer hose.
Separate the 2 hood supports.
Remove the 4 bolts, then remove the hood.
| 6. REMOVE RADIATOR SUPPORT TO FRAME SEAL LH |
![]() |
Disengage the 9 clips, then remove the radiator support to frame seal.
| 7. REMOVE FAN SHROUD |
![]() |
Disconnect the hose from the radiator reserve tank.
![]() |
Remove the 2 cooler hoses from the clamp (with automatic transmission).
Remove the 4 nuts from the fan pulley.
Remove the fan and generator V belt .
Remove the 2 bolts from the fan shroud.
Remove the fan pulley and fan shroud.
| 8. REMOVE RADIATOR ASSEMBLY |
![]() |
Disconnect the 2 radiator hoses.
Remove the 4 bolts, then remove the radiator.
Disconnect the 2 oil cooler hoses (with automatic transmission).

| 9. REMOVE V-BANK COVER |
![]() |
Remove the 2 nuts, then remove the V-bank cover.
| 10. REMOVE AIR CLEANER ASSEMBLY |
![]() |
Disconnect the ventilation hose No. 2.
![]() |
Disconnect the vacuum hose.
Disconnect the mass air flow meter connector.
Remove the 2 wire harness clamps.
![]() |
Loosen the 2 hose clamps.
Remove the 2 bolts, then remove the air cleaner.
| 11. REMOVE AIR PUMP ASSEMBLY (w/ Secondary Air Injection System) |
| 12. REMOVE NO. 2 AIR CLEANER HOSE (w/ Secondary Air Injection System) |
![]() |
Remove the 2 bolts, then remove the No. 2 air cleaner hose.
| 13. REMOVE AIR SWITCHING VALVE ASSEMBLY (w/ Secondary Air Injection System) |
| 14. REMOVE AIR TUBE ASSEMBLY (w/ Secondary Air Injection System) |
![]() |
Remove the bolt.
Disconnect the 2 wire harness clamps.
![]() |
Remove the bolt then, remove the air tube assembly.
| 15. REMOVE TRANSMISSION ASSEMBLY |
| Transmission | Drive Type | See page |
| Manual Transmission | 2WD |
Click here
|
| Manual Transmission | 4WD |
Click here
|
| Automatic Transmission | 2WD |
Click here
|
| Automatic Transmission | 4WD |
Click here
|
| 16. REMOVE CLUTCH COVER ASSEMBLY (for Manual Transmission) |
| Transmission | See page |
| RA60 |
Click here
|
| RA60F |
Click here
|
| 17. REMOVE CLUTCH DISC ASSEMBLY (for Manual Transmission) |
| Transmission | See page |
| RA60 |
Click here
|
| RA60F |
Click here
|
| 18. REMOVE FAN PULLEY |
| 19. REMOVE VANE PUMP ASSEMBLY |
![]() |
Disconnect the power steering pressure switch connector.
Remove the 2 bolts, then separate the vane pump.
| 20. REMOVE GENERATOR ASSEMBLY |
![]() |
Disconnect the wire harness.
Remove the bolt and wire harness stay.
Disconnect the connector from the generator assembly.
Remove the terminal cap and nut.
Disconnect the wire harness from terminal B.
![]() |
Remove the 2 bolts, then separate the wire harness clamp bracket from the generator assembly.
![]() |
Remove the 2 bolts, then remove the generator assembly.
| 21. SEPARATE COOLER COMPRESSOR ASSEMBLY |
![]() |
Remove the bolt, then separate the suction hose sub-assembly.
![]() |
Disconnect the cooler compressor assembly connector.
Remove the 4 bolts, then separate the cooler compressor assembly from the V-ribbed belt tensioner assembly.
| 22. DISCONNECT NO. 1 FUEL PIPE SUB-ASSEMBLY |
![]() |
Remove the fuel pipe clamp.
Pinch the tube connector, and then pull the fuel pipe out of the pipe as shown in the illustration.
| 23. DISCONNECT NO. 2 FUEL PIPE SUB-ASSEMBLY |
![]() |
Remove the fuel pipe clamp.
Pinch the tube connector, and then pull the fuel pipe out of the pipe as shown in the illustration.
| 24. DISCONNECT HEATER WATER INLET HOSE |
| 25. DISCONNECT HEATER WATER OUTLET HOSE |
| 26. REMOVE INTAKE AIR SURGE TANK |
![]() |
Disconnect the 2 water by-pass hoses.
![]() |
Disconnect the fuel vapor feed hose.
![]() |
Disconnect the ventilation hose.
![]() |
Disconnect the 2 VSV connectors.
Disconnect the throttle body with motor connector.
Separate the 3 wire harness clamps and hose clamp.
![]() |
Remove the nut, then separate the clutch flexible hose bracket from the surge tank stay (with Manual Transmission).
![]() |
Remove the 2 bolts and throttle body bracket.
![]() |
Remove the bolt and oil baffle plate.
Remove the 4 bolts and 2 surge tank stays.
![]() |
Remove the 2 nuts.
Using a socket hexagon wrench 8, remove the 4 bolts, intake air surge tank and gasket.
| 27. SEPARATE ENGINE WIRE |
Remove the glove compartment door.
Remove the instrument panel finish panel sub-assembly lower RH.
Disconnect the 7 connectors from the ECM.
Disconnect the connector from four wheel drive ECU (4WD only).
Disengage the wire harness clamp.
Pull the wire harness into the engine room.
Disconnect the front differential connector (4WD only).
![]() |
Disconnect the 3 connectors from the engine room relay block.
Remove the nut, then separate the engine wire from the engine room relay block.
| 28. SEPARATE NO. 2 ENGINE WIRE |
Disconnect the ground cable from the cylinder block.
| 29. REMOVE ENGINE ASSEMBLY |
![]() |
Install the 2 engine hangers with the 4 bolts as shown in the illustration.
| *1 | No. 1 Engine Hanger |
| *2 | No. 2 Engine Hanger |
| No. 1 engine hanger | 12281-31070 |
| No. 2 engine hanger | 12282-31050 |
| Bolt | 90119-08177 |
Attach the engine sling device and hang the engine with the chain block.
![]() |
Remove the 4 bolts and 4 nuts, and separate the engine mounting brackets from the frame brackets.
Lift the engine out of the vehicle carefully.
Place the engine onto a working bench.
| 30. REMOVE FLYWHEEL SUB-ASSEMBLY (for Manual Transmission) |
![]() |
Using SST, hold the crankshaft.
![]() |
Remove the 8 bolts, then remove the flywheel and 2 spacers.
| 31. REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for Automatic Transmission) |
![]() |
Using SST, hold the crankshaft.
![]() |
Remove the 8 bolts, then remove the drive plate and 2 spacers.
| 32. REMOVE HEATER WATER INLET HOSE |
![]() |
| 33. REMOVE HEATER WATER OUTLET HOSE |
![]() |
| 34. REMOVE VENTILATION HOSE |
![]() |
| 35. REMOVE NO. 2 VENTILATION HOSE |
![]() |
| 36. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY RH |
Remove the 6 nuts, exhaust manifold and gasket.
| 37. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY LH |
Remove the 6 nuts, exhaust manifold and gasket.
| 38. REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET RH |
![]() |
Remove the 4 bolts, then remove the engine mounting bracket RH.
| 39. REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET LH |
![]() |
Remove the 3 bolts, then remove the engine mounting bracket LH.
| 40. REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY |
Remove the 2 bolts, then remove the 2 idler pulleys.
| 41. REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY |
Remove the bolt, then remove the idler pulley.
| 42. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY |
![]() |
Remove the 5 bolts, then remove the V-ribbed belt tensioner.
| 43. REMOVE WATER INLET |
![]() |
Remove the 3 nuts, then remove the water inlet with thermostat and gasket.
| 44. REMOVE OIL FILTER BRACKET SUB-ASSEMBLY |
Remove the 3 bolts and 2 nuts, then remove the oil filter bracket and gasket.
| 45. REMOVE INTAKE MANIFOLD |
Disconnect the 6 fuel injector connectors.
![]() |
Remove the 10 bolts, then remove the intake manifold and gasket.
| 46. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY |
![]() |
Disconnect the 2 connectors.
Remove the 2 bolts, then remove the 2 camshaft timing oil control valves.
| 47. REMOVE WATER BY-PASS JOINT REAR |
Disconnect the engine coolant temperature sensor connector.
Disconnect the heater hose.
![]() |
Remove the 2 bolts and 4 nuts, then remove the water by-pass joint RR and 2 gaskets.
Remove the O-ring from the water outlet hose.
| 48. REMOVE OIL FILTER CAP SUB-ASSEMBLY |
| 49. REMOVE OIL FILLER CAP HOUSING |
Remove the 2 nuts, oil filler cap housing and gasket.
| 50. REMOVE IGNITION COIL ASSEMBLY |
![]() |
Disconnect the 6 connectors.
Remove the 6 bolts, then remove the 6 ignition coils.
| 51. REMOVE SPARK PLUG |
| 52. REMOVE OIL LEVEL DIPSTICK SUB-ASSEMBLY |