Home › ENGINE ยท 1GR-FE › LUBRICATION › OIL PUMP (for 4WD and Pre-Runner)

OIL PUMP (for 4WD and Pre-Runner) > REMOVAL

for Preparation Click here



1. DISCHARGE FUEL SYSTEM PRESSURE
(Click here)


2. REMOVE BATTERY


3. DRAIN ENGINE COOLANT


A070279E01

CAUTION:
To avoid the danger of being burned, do not remove the radiator cap while the engine and radiator are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator.

  1. Remove the service hole cover from the engine under cover.

  1. Install a vinyl hose onto the drain on the radiator side.

  1. Fix the vinyl hose with tape.



    A076320E02
  1. Loosen the 3 drain plugs on the engine and radiator, and drain the coolant.

  1. Remove the radiator cap.

  1. Drain the coolant from the reservoir tank.

  1. Tighten the 3 drain plugs.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf } for the engine

  1. Remove the vinyl hose from the radiator.



4. DRAIN ENGINE OIL
  1. Remove the engine under cover seal No. 3.

  1. Remove the oil pan drain plug and drain the engine oil.

  1. Clean the oil pan drain plug and install it with a new gasket.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



5. REMOVE POWER STEERING LINK ASSEMBLY
(Click here)


6. REMOVE FRONT DIFFERENTIAL CARRIER ASSEMBLY (for 4WD)
(Click here)


7. REMOVE V-BANK COVER


A075593E01
  1. Remove the 2 nuts, then remove the V-bank cover.



8. REMOVE RADIATOR SUPPORT TO FRAME SEAL LH


G036137E02
  1. Disengage the 9 clips, then remove the radiator support to frame seal.



9. REMOVE FAN SHROUD


G036138E01
  1. Disconnect the hose from the radiator reserve tank.



    G036139E01
  1. Remove the 2 cooler hoses from the clamp (with automatic transmission).

  1. Remove the 4 nuts from the fan pulley.

  1. Remove the fan and generator V belt .

  1. Remove the 2 bolts from the fan shroud.

  1. Remove the fan pulley and fan shroud.



10. REMOVE AIR CLEANER ASSEMBLY


A075594E01
  1. Disconnect the ventilation hose No. 2.



    A075595E01
  1. Disconnect the vacuum hose.

  1. Disconnect the mass air flow meter connector.

  1. Remove the 2 wire harness clamps.



    A075596E01
  1. Loosen the 2 hose clamps.

  1. Remove the 2 bolts, then remove the air cleaner.



11. REMOVE AIR PUMP ASSEMBLY (w/ Secondary Air Injection System)
(Click here)


12. REMOVE NO. 2 AIR CLEANER HOSE (w/ Secondary Air Injection System)


A261697
  1. Remove the 2 bolts, then remove the No. 2 air cleaner hose.



13. REMOVE AIR SWITCHING VALVE ASSEMBLY (w/ Secondary Air Injection System)
(Click here)


14. REMOVE AIR TUBE ASSEMBLY (w/ Secondary Air Injection System)


A261696
  1. Remove the bolt.

  1. Disconnect the 2 wire harness clamps.



    A261695
  1. Remove the bolt then, remove the air tube assembly.



15. REMOVE OIL LEVEL GAUGE GUIDE


16. REMOVE WATER INLET


A076319E02
  1. Remove the 3 nuts, then remove the water inlet with thermostat and gasket.



17. SEPARATE PUMP ASSEMBLY, VANE


A076444E02
  1. Disconnect the power steering pressure switch connector.

  1. Remove the 2 bolts, then separate the vane pump.

    NOTICE:
    Do not hit the pulley with other parts when separating the vane pump.

    HINT:
    The vane pump is suspended securely.



18. REMOVE GENERATOR ASSEMBLY


A076407E01
  1. Disconnect the wire harness.

    1. Remove the bolt and wire harness stay.

    2. Disconnect the connector from the generator assembly.

    3. Remove the terminal cap and nut.

    4. Disconnect the wire harness from terminal B.



    A076408E01
  1. Remove the 2 bolts, then separate the wire harness clamp bracket from the generator assembly.



    A076409E01
  1. Remove the 2 bolts, then remove the generator assembly.



19. SEPARATE COOLER COMPRESSOR ASSEMBLY


G036154E01
  1. Remove the bolt, then separate the suction hose sub-assembly.



    G036155E01
  1. Disconnect the cooler compressor assembly connector.

  1. Remove the 4 bolts, then separate the cooler compressor assembly from the V-ribbed belt tensioner assembly.



20. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY


A076445E01
  1. Remove the 5 bolts, then remove the V-ribbed belt tensioner.



21. REMOVE NO.2 IDLER PULLEY SUB-ASSEMBLY
  1. Remove the 2 bolts, then remove the idler pulley No. 2.



22. REMOVE NO.1 IDLER PULLEY SUB-ASSEMBLY
  1. Remove the bolt, then remove the idler pulley No. 1.



23. REMOVE CRANKSHAFT PULLEY


A072947E02
  1. Using SST, hold the crankshaft pulley and loosen the pulley set bolt.

    SST
    09213-54015   (91651-60855)
    09330-00021  



    A072948E01
  1. Using the pulley set bolt and SST, remove the crankshaft pulley.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05031)



24. REMOVE NO.2 OIL PAN SUB-ASSEMBLY


    A072949E01
  1. Remove the 10 bolts and 2 nuts.



    A072950E03
  1. Insert the blade of the oil pan seal cutter between the oil pan and oil pan No. 2, cut off applied sealer and remove the oil pan No. 2.

    NOTICE:
    1. Be careful not to damage the contact surfaces of the oil pan and oil pan No. 2.
    2. Be careful not to damage the oil pan No. 2 flange.



25. REMOVE OIL STRAINER SUB-ASSEMBLY


A072951E01
  1. Remove the 2 nuts, then remove the oil strainer and gasket.



26. REMOVE OIL PAN SUB-ASSEMBLY


A076446E01
  1. Remove the 4 housing bolts.

  1. Remove the flywheel housing under cover.



    A072952E01
  1. Remove the 17 bolts and 2 nuts.



    G036806E01
  1. Using a screwdriver, remove the oil pan by prying between the oil pan and cylinder block.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder block and oil pan.

  1. Remove the O-ring from the oil pump.



27. REMOVE INTAKE AIR SURGE TANK


A075597E01
  1. Disconnect the water by-pass hose No. 5.



    A075598E01
  1. Disconnect the water by-pass hose No. 4.



    A075644E01
  1. Disconnect the fuel vapor feed hose.



    A075645E01
  1. Disconnect the ventilation hose.



    A075646E01
  1. Disconnect the 2 VSV connectors.

  1. Disconnect the throttle motor connector.

  1. Remove the 3 wire harness clamps and hose clamp.



    A075647E01
  1. Remove the 3 upper bolts which are used to secure the 2 surge tank stays and throttle body bracket.



    A075648E02
  1. Using an 8 mm socket hexagon wrench, remove the 4 bolts.

  1. Remove the 2 nuts, then remove the intake air surge tank and gasket.



28. REMOVE IGNITION COIL ASSEMBLY


G036133E01
  1. Disconnect the 6 connectors.

  1. Remove the 6 bolts, then remove the 6 ignition coils.



29. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY


A072943E01
  1. Remove the 10 bolts, 3 seal washers, 2 nuts, cylinder head cover and gasket.



30. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH


A076503E01
  1. Remove the 10 bolts, 3 seal washers, 2 nuts, cylinder head cover and gasket.



31. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY


G036118E01
  1. Disconnect the 2 connectors.

  1. Remove the 2 bolts, then remove the 2 camshaft timing oil control valves.



32. REMOVE VVT SENSOR


A076413E01
  1. RH bank side VVT sensor:

    1. Disconnect the VVT sensor connector.

    2. Remove the bolt and VVT sensor.



    A076414E01
  1. LH bank side VVT sensor:

    1. Disconnect the water by-pass hoses No. 4 and No. 5 .

    2. Disconnect the VVT sensor connector.



    3. A076415E01
    4. Remove the bolt and VVT sensor.



33. REMOVE OIL FILTER BRACKET SUB-ASSEMBLY
  1. Remove the 3 bolts, 2 nuts, oil filter bracket and gasket.



34. REMOVE TIMING CHAIN OR BELT COVER SUB-ASSEMBLY


G036303E01
  1. Remove the 24 bolts and 2 nuts.



    G036304E01
  1. Remove the timing chain cover by prying between the timing chain cover and cylinder head or cylinder block with a screwdriver.

    NOTICE:
    Be careful not to damage the contact surfaces of the timing chain cover, cylinder block and cylinder head.

  1. Remove the O-ring from the LH cylinder head.



35. REMOVE TIMING GEAR CASE OR TIMING CHAIN CASE OIL SEAL


A072957E01
  1. Using a screwdriver, pry out the oil seal.

    NOTICE:
    Be careful not to damage the oil pump assembly. Wrap a tip of the screwdriver with tape.