Home › ENGINE · 1GR-FE › ENGINE MECHANICAL › CYLINDER HEAD (for Bank 1 4WD and Pre-Runner)

CYLINDER HEAD (for Bank 1 4WD and Pre-Runner) > INSTALLATION

for Preparation Click here



1. INSTALL CYLINDER HEAD GASKET
  1. Remove any old packing (FIPG) material and be careful not to drop any oil on the contact surfaces of the cylinder head and cylinder block.



    A076271E08
  1. Apply a continuous bead of the seal packing (diameter 2.5 to 3 mm (0.098 to 0.118 in.)) to a new cylinder head gasket as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    NOTICE:
    Install the cylinder head within 3 minutes of applying seal packing. Tighten the cylinder head bolts within 15 minutes of installing the cylinder head. Otherwise, the seal packing must be removed and reapplied.



    A076272E03
  1. Place the cylinder head gasket on the cylinder block surface with the Lot No. stamp upward.

    NOTICE:
    1. Be careful of the installation direction.
    2. Place the cylinder head carefully in order not to damage the gasket with the bottom part of the head.



2. INSTALL CYLINDER HEAD SUB-ASSEMBLY
  1. Place the cylinder head on the cylinder head gasket.



  1. Install the 8 cylinder head bolts.

    HINT:
    1. The cylinder head bolts are tightened in 2 successive steps (steps (3) and (5)).
    2. If any cylinder head bolts are broken or deformed, replace them.


    1. Apply a light coat of engine oil to the threads of the cylinder head bolts.

    2. Install the plate washer onto the cylinder head bolt.



    3. A076273E02
    4. Using several steps, tighten each bolt uniformly with a 10 mm bi-hexagon wrench in the sequence shown in the illustration.

      Torque:
      36 N*m{ 367 kgf*cm , 27 ft.*lbf }

      If any cylinder head bolts do not meet the torque specification, replace them.

      NOTICE:
      Do not drop the washers into the cylinder head.



    5. A076274E02
    6. Mark the front side of each cylinder head bolt with paint.

    7. Retighten the cylinder head bolts 180° as shown.

    8. Check that the painted marks are now at 180° from the engine front.

  1. Install the ground cables with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



3. INSTALL NO.2 CAMSHAFT BEARING


A076279E01
  1. Install the camshaft bearing No. 2 onto the cylinder head.

    NOTICE:
    Clean the installation planes of the back side of the bearing and cylinder head and keep them free of oils and fats.



4. INSTALL CAMSHAFTS

NOTICE:
Keep the camshaft level while it is being removed. The camshaft thrust clearance is very small and failing to keep it level could crack or damage the cylinder head journal surface, which receives the thrust. This could subsequently lead the camshaft to seize or break. Perform the following steps to avoid such problems.



    A076280E02
  1. Set the crankshaft position.

    1. Using the crankshaft pulley set bolt, turn the crankshaft, and set the crankshaft set key in the left horizontal position.

      NOTICE:
      Installing the crankshaft at the wrong angle could cause the piston head and valve head to come into contact with each other when installing the camshaft. This could cause damage, so always set the crankshaft at the correct angle.

  1. Apply new engine oil to the thrust portion and journal of the camshafts.



    A076281E03
  1. Place the 2 camshafts onto the cylinder head with the cam lobes of No. 1 cylinder facing in the directions shown in the illustration.



    A076282E03
  1. Install the 8 bearing caps in the proper locations as shown.

  1. Apply a light coat of engine oil to the threads and under the heads of the bearing cap bolts.



    A072967E06
  1. Using several steps, uniformly install and tighten the 16 bearing cap bolts in the sequence shown in the illustration.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf } for 10 mm (0.39 in.) head
    24 N*m{ 245 kgf*cm , 18 ft.*lbf } for 12 mm (0.47 in.) head



    A076283E02
  1. Turn the camshafts clockwise until the knock pin comes to a position 90° to the cylinder head.



5. INSTALL NO.2 CHAIN TENSIONER ASSEMBLY


A076286E01
  1. While pushing in the tensioner, insert a pin of φ 1.0 mm (0.039 in.) into the hole to fix it.



    A072962E01
  1. Install the chain tensioner No. 2 with the bolt.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }



6. INSTALL CAMSHAFT TIMING GEARS AND NO.2 CHAIN (for Bank 1)


A076287E03
  1. Align the yellow mark links with the timing marks (1 dot mark) of camshaft timing gears as shown in the illustration.



    G036257E01
  1. Align the timing marks on the camshaft timing gears with the timing marks on the bearing caps, and install the camshaft timing gears with the chain onto the RH camshafts.

  1. Temporarily install the 2 camshaft timing gear bolts.

    NOTICE:
    Do not push the camshaft timing gear assembly onto the camshaft forcibly when installing it.



    G036252E01
  1. Hold the hexagonal portion of the camshaft with a wrench, and tighten the 2 bolts.

    Torque:
    100 N*m{ 1,020 kgf*cm , 74 ft.*lbf }

  1. Remove the pin from the tensioner No. 2.



7. INSTALL WATER BY-PASS JOINT REAR


A076535E01
  1. Install a new O-ring onto the water outlet pipe.

  1. Apply soapy water to the O-ring.

  1. Install 2 new gaskets and water by-pass joint rear with the 2 bolts and 4 nuts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. Connect the heater hose.

  1. Connect the engine coolant temperature sensor connector.



8. INSTALL INTAKE MANIFOLD


A076536E01
  1. Set a new gasket on each cylinder head.

    NOTICE:
    1. Align the port holes of the gasket and cylinder head.
    2. Be careful of the installation direction.

  1. Set the intake manifold on the cylinder heads.

  1. Install and tighten the 10 bolts uniformly in several steps.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }

  1. Connect the 6 fuel injector connectors.



9. CONNECT NO.2 FUEL PIPE SUB-ASSEMBLY


10. CONNECT NO.1 FUEL PIPE SUB-ASSEMBLY
  1. Push the tube connector into the pipe until the tube connector makes a "click" sound.

    NOTICE:
    1. Check if there is any damage or foreign objects on the connected part of the fuel pipe.
    2. After connecting, check that the pipe and connector are securely connected by pulling them.

  1. Install the fuel pipe clamp.



11. INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY RH


A076440E03
  1. Set a new gasket to the RH cylinder head with the oval shape facing forward.

    NOTICE:
    Be careful of the installation direction.

  1. Install the exhaust manifold with the 6 nuts. Tighten the nuts uniformly in several steps.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }

  1. Connect the air fuel ratio sensor connector.



12. INSTALL MANIFOLD STAY
  1. Install the manifold stay with the 3 bolts.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



13. INSTALL FRONT EXHAUST PIPE ASSEMBLY
(Click here)


14. INSTALL NO.1 COOL AIR INLET
  1. Install the cool air inlet with the 2 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9.0 ft.*lbf }



15. INSTALL CHAIN TENSIONER SLIPPER


16. INSTALL NO.1 CHAIN TENSIONER ASSEMBLY


A076294E02
  1. While turning the stopper plate of the tensioner clockwise, push in the plunger of the tensioner as shown in the illustration.

  1. While turning the stopper plate of the tensioner counterclockwise, insert a bar of φ 35 mm (0.138 in.) into the holes in the stopper plate and tensioner to fix the stopper plate.

  1. Install the chain tensioner with the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7.4 ft.*lbf }



17. INSTALL CHAIN SUB-ASSEMBLY
(Click here)


18. INSTALL TIMING CHIAN OR BELT COVER SUB-ASSEMBLY
(Click here)


19. INSTALL FRONT DIFFERENTIAL CARRIER ASSEMBLY (for 4WD)
(Click here)


20. INSTALL POWER STEERING LINK ASSEMBLY
(Click here)


21. INSTALL BATTERY


22. ADD ENGINE OIL
  1. Fill with fresh engine oil.

    Standard engine oil:

    Oil grade
    Oil viscosity (SAE)
    ILSAC multigrade engine oil
    5W-30


    Standard capacity (for 2WD):

    Item
    Specified Condition
    Drain and refill with oil filter change
    4.5 liters (4.8 US qts, 4.0 lmp. qts)
    Drain and refill without oil filter change
    4.2 liters (4.4 US qts, 3.7 lmp. qts)
    Dry fill
    5.6 liters (5.9 US qts, 4.9 lmp. qts)


    Standard capacity (for PRE RUNNER and 4WD):

    Item
    Specified Condition
    Drain and refill with oil filter change
    5.2 liters (5.5 US qts, 4.6 lmp. qts)
    Drain and refill without oil filter change
    4.9 liters (5.2 US qts, 4.3 lmp. qts)
    Dry fill
    6.0 liters (6.3 US qts, 5.3 lmp. qts)

  1. Reinstall the oil filler cap.



23. ADD ENGINE COOLANT
  1. Pour coolant into the radiator until it overflows.

    Capacity:

    Transmission
    Capacity
    Manual Transmission
    9.7 liters (10.3 Us qts, 8.5 Imp. qts)
    Automatic Transmission
    9.8 liters (10.4 Us qts, 8.6 Imp. qts)

    HINT:
    1. Use of improper coolants may damage the engine cooling system.
    2. Use only Toyota Super Long Life Coolant or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, and non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
    3. New Toyota vehicles are filled with Toyota Super Long Life Coolant (color is pink, premixed ethylene glycol concentration is approximately 50 % and freezing temperature is -35°C (-31°F)). When replacing the coolant, Toyota Super Long Life Coolant is recommended.

    NOTICE:
    Do not substitute plain water for engine coolant.

  1. Check the coolant level inside the radiator by squeezing the inlet and outlet radiator hoses several times by hand. If the coolant level goes down, add coolant.

  1. Install the radiator cap securely.

  1. Slowly pour coolant into the radiator reservoir until it reaches the FULL line.

  1. Warm up the engine until the cooling fan operates.

    1. Set the air conditioning as follows while warming up the engine.

      Item
      Condition
      Fan Speed
      Any setting except OFF
      Temperature
      Toward WARM
      Air Conditioning Switch
      OFF

    2. Maintain the engine speed at 2,000 to 2,500 rpm and warm up the engine until the cooling fan operates.

  1. Squeeze the inlet and outlet radiator hoses several times by hand while warming up the engine.

  1. Stop the engine and wait until the coolant cools down.

  1. Remove the radiator cap and check the coolant level inside the radiator.

  1. If the coolant level is below the full level, perform the steps from (a) through (h) and repeat the operation until the coolant level remains at the full level.

  1. Check the coolant level inside the radiator reservoir tank again. If it is below the full level, add coolant.



24. ADD DIFFERENTIAL OIL (for 4WD)


25. INSPECT DIFFERENTIAL OIL (for 4WD)


D025304E37
  1. Stop the vehicle on a level place.

  1. Remove the differential filler plug and gasket.

  1. Check that the oil level is within 5 mm (0 to 0.20 in.) of the bottom of the filler plug opening.

    NOTICE:
    1. Excessively large or small quantities of oil may cause problems.
    2. After replacing the oil, drive the vehicle and check the oil level again.

    HINT:
    If necessary, fill the differential carrier assembly with differential gear oil.

    Oil type and viscosity:
    Toyota Genuine Differential gear oil LT APL 75W-85 GL-5 or equivalent.

    Capacity:
    Front differential carrier assembly:
    1.45 to 1.55 liters
    (1.54 to 1.64 US qts, 1.28 to 1.36 lmp. qts)
    Rear differential carrier assembly (for 2WD):
    3.26 to 3.36 liters
    (3.45 to 3.55 US qts, 2.87 to 2.95 lmp. qts)
    Rear differential carrier assembly (for Pre, 4WD):
    2.75 to 2.85 liters
    (2.91 to 3.01 US qts, 2.42 to 2.50 lmp. qts)

  1. Check for oil leakage if the oil level is low.

  1. Install the differential filler plug and a new gasket.

    Torque:
    Front differential carrier assembly:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }
    Rear differential carrier assembly:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }



26. ADD POWER STEERING FLUID


27. BLEED POWER STEERING FLUID
  1. Check the fluid level.

  1. Jack up the front of the vehicle and support it with stands.

  1. Turn the steering wheel.

    1. With the engine stopped, turn the wheel slowly from lock to lock several times.

  1. Lower the vehicle.

  1. Start the engine.

    1. Run the engine at idle for a few minutes.

  1. Turn the steering wheel.

    1. With the engine idling, turn the wheel to the left or right full lock position and keep it there for 2 to 3 seconds. Then turn the wheel to the opposite full lock position and keep it there for 2 to 3 seconds (step A).

    2. Repeat step A several times.

  1. Stop the engine.



    C114971E01
  1. Check for foaming or emulsification.
    Especially, if the system has to be bled twice because of foaming or emulsification, check for fluid leakage in the system.

  1. Check the fluid level.



28. CHECK FOR ENGINE OIL LEAKAGE


29. CHECK FOR ENGINE COOLANT LEAKAGE
  1. Fill the radiator with coolant and attach a radiator cap tester.

  1. Pump it to 118 kPa (1.2 kgf/cm2 17.1 psi), then check for leakage.



30. CHECK FOR FUEL LEAKAGE


31. CHECK FOR EXHAUST GAS LEAKAGE


32. CHECK FOR POWER STEERING FLUID LEAKAGE


33. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
(Click here)


34. INSPECT IGNITION TIMING

NOTICE:
  1. Turn all electrical systems OFF.
  1. Operate the inspection when the cooling fan motor is turned OFF.

  1. Warm up the engine.

  1. When using the Techstream.

    1. Connect the Techstream to the DLC3.

    2. Enter the following menu items:
      Select: Powertrain / Engine and ECT / Data List / IGN Advance.

    3. Inspect the ignition timing during idling.

      Ignition timing:
      7 to 24° BTDC @ idle (Transmission in neutral position)

    4. Check that the ignition timing advances immediately when the engine speed is increased.



    A118802E01
  1. When not using Techstream.

    1. Using SST, connect the terminals 13 (TC) and 4 (CG) of the DLC3.

      SST
      09843-18040  

      NOTICE:
      Be sure not to connect the terminals wrongly. It causes breakage of the engine.

    2. Remove the air cleaner.



    3. A076315E02
    4. Pull out the wire harness as shown in the illustration.

    5. Connect the tester probe of a timing light to the wire of the ignition coil connector for No. 1 cylinder.

      NOTICE:
      1. Use a timing light that detects the first signal.
      1. After checking, be sure to wrap the wire harness with tape.



    6. A076316E01
    7. Inspect the ignition timing during idling.

      Ignition timing:
      8 to 12° BTDC @ idle (Transmission in neutral position)

    8. Remove the SST from the DLC3.

    9. Inspect the ignition timing during idling.

      Ignition timing:
      7 to 24° BTDC @ idle (Transmission in neutral position)

    10. Install the air cleaner.



35. INSPECT ENGINE IDLING SPEED

NOTICE:
  1. Turn all the electrical systems OFF.
  1. Operate the inspection when the cooling fan motor is turned OFF.

  1. Warm up the engine.

  1. When using the Techstream:

    1. Connect the Techstream to the DLC3.

    2. Enter the following menu items:
      Select: Powertrain / Engine and ECT / Data List / Engine Speed.

    3. Inspect the engine idling speed.

      Idling speed:
      650 to 750 rpm (Transmission in neutral position)



    A118802E02
  1. When not using the Techstream:

    1. Using SST, connect the terminal 8 (TAC) of the DLC3.

      SST
      09843-18030  

    2. Race the engine speed at 2,500 rpm for approximately 90 seconds.

    3. Inspect the engine idling speed.

      Idling speed:
      650 to 750 rpm (Transmission in neutral position)



36. INSPECT CO/HC
  1. Start the engine.

  1. Run the engine at 2,500 rpm for approximately 180 seconds.

  1. Insert the CO/HC meter testing probe at least 40 cm (1.3 ft) into the tailpipe during idling.

  1. Immediately check the CO/HC concentration during idling and/or at 2,500 rpm.

    HINT:
    1. Complete the measurement within 3 minutes.
    1. When carrying out the 2 modes (idling and 2,500 rpm) test, the measurement orders are prescribed by the applicable local regulations.

  1. If the CO/HC concentration does not comply with regulations, troubleshoot in the order given below.

    1. Check the heated oxygen sensor operation.

      CO
      HC
      Problems
      Causes
      Normal
      High
      Rough idling
      1. Faulty ignition:
        1. Incorrect timing
        1. Fouled, shorted or improperly gapped plugs
      2. Incorrect valve clearance
      3. Leaky intake and exhaust valves
      4. Leaky cylinders
      Low
      High
      Rough idling
      (Fluctuating HC reading)
      1. Vacuum leaks:
        1. PCV hoses
        1. Intake manifold
        1. Throttle body
        1. IAC valve
        1. Brake booster line
      2. Lean mixture causing misfire
      High
      High
      Rough idling
      (Black smoke from exhaust)
      1. Restricted air filter
      2. Plugged PCV valve
      3. Faulty EFI systems:
        1. Faulty pressure regulator
        1. Faulty engine coolant temperature sensor
        1. Faulty mass air flow meter
        1. Faulty ECM
        1. Faulty injectors
        1. Faulty throttle position sensor



37. REMOVE COMPRESSION
  1. Warm up and stop the engine.

  1. Remove the circuit opening relay.

  1. Remove the V-bank cover.

  1. Remove the air cleaner assembly.

  1. Remove the ignition coils.

  1. Remove the spark plugs.



    A076317E01
  1. Inspect the cylinder compression pressure.

    1. Insert a compression gage into the spark plug hole.

      SST
      09992-00500  

    2. Fully open the throttle.

    3. While cranking the engine, measure the compression pressure.

      Compression pressure:
      1,300 kPa (13.3 kgf/cm2, 189 psi)

      Minimum pressure:
      1,000 kPa (10.2 kgf/cm2, 145 psi)

      Difference between each cylinder:
      100 kPa (1.0 kgf/cm2, 15 psi)

      NOTICE:
      1. Use a fully-charged battery so the engine speed can be increased to 250 rpm or more.
      1. Inspect the other cylinders in the same way.
      1. Measure the compression in as short a time as possible.

    4. If the cylinder compression is low, pour a small amount of engine oil into the cylinder through the spark plug hole and repeat steps (1) through (3) for cylinders with low compression.

      1. If adding oil increases the compression, the piston rings and/or cylinder bore may be worn or damaged.
      1. If pressure stays low, a valve may be stuck or seated improperly, or there may be leakage from the gasket.