CYLINDER HEAD (for Bank 2 4WD and Pre-Runner) > INSTALLATION |
| 1. INSTALL NO.2 CYLINDER HEAD GASKET |
Remove any old packing (FIPG) material and be careful not to drop any oil on the contact surface of the cylinder head and cylinder block.
![]() |
Apply a continuous bead of seal packing (diameter 2.5 to 3.0 mm (0.098 to 0.118 in.)) to a new cylinder head gasket as shown in the illustration.
![]() |
Place the cylinder head gasket on the cylinder block surface with the Lot No. stamp upward.
| 2. INSTALL CYLINDER HEAD LH |
Place the cylinder head on the cylinder head gasket.
Install the 8 cylinder head bolts.
Apply a light coat of engine oil to the threads of the cylinder head bolts.
Install the plate washer onto the cylinder head bolt.
![]() |
Using several steps, uniformly tighten each bolt with a 10 mm bi-hexagon wrench in the sequence shown in the illustration.
![]() |
Mark the front side of each cylinder head bolt with paint.
Retighten the cylinder head bolts 180° as shown.
Check that the painted marks are now at 180° from the engine front.
![]() |
Install the 2 cylinder head bolts.
Apply a light coat of engine oil to the threads of the cylinder head bolts.
Using several steps, uniformly install and tighten the 2 cylinder head bolts in the sequence as shown in the illustration.
Install the ground cables with the 2 bolts.
| 3. INSTALL CAMSHAFTS |
![]() |
Set the crankshaft position.
Using the crankshaft pulley set bolt, turn the crankshaft, and set the crankshaft set key in the left horizontal position.
Apply new engine oil to the thrust portion and journal of the camshafts.
![]() |
Place the 2 camshafts onto the cylinder head with the cam lobes of No. 1 cylinder facing in the directions shown in the illustration.
![]() |
Install the 8 bearing caps in the proper locations as shown.
Apply a light coat of engine oil to the threads and under the leads of the bearing cap bolts.
![]() |
Using several steps, uniformly install and tighten the 16 bearing cap bolts in the sequence as shown in the illustration.
| 4. INSTALL NO.2 CHAIN TENSIONER ASSEMBLY |
![]() |
While pushing in the tensioner, insert a pin of φ 1.0 mm (0.039 in.) into the hole to fix it.
![]() |
Install the chain tensioner No. 2 with the bolt.
| 5. INSTALL CAMSHAFT TIMING GEARS AND NO.2 CHAIN (for Bank 2) |
![]() |
Align the yellow mark links with the timing marks (1 dot mark and 2 dot marks) of camshaft timing gears as shown in the illustration.
![]() |
Align the timing marks on the camshaft timing gears with the timing marks on the bearing caps, and install the camshaft timing gears with the chain onto the LH camshafts.
Temporarily install the 2 camshaft timing gear bolts.
![]() |
Hold the hexagonal portion of the camshaft with a wrench, and tighten the 2 bolts.
Remove the pin from the tensioner No. 2.
| 6. INSTALL NO.1 CHAIN VIBRATION DAMPER |
![]() |
Install the chain vibration damper with the 2 bolts.
| 7. INSTALL WATER BY-PASS JOINT REAR |
![]() |
Install a new O-ring onto the water outlet pipe.
Apply soapy water to the O-ring.
Install 2 new gaskets and water by-pass joint rear with the 2 bolts and 4 nuts.
Connect the heater hose.
Connect the engine coolant temperature sensor connector.
| 8. INSTALL INTAKE MANIFOLD |
![]() |
Set a new gasket on each cylinder head.
Set the intake manifold on the cylinder heads.
Install and tighten the 10 bolts uniformly in several steps.
Connect the 6 fuel injector connectors.
| 9. CONNECT NO.2 FUEL PIPE SUB-ASSEMBLY |
| 10. CONNECT NO.1 FUEL PIPE SUB-ASSEMBLY |
Push the tube connector into the pipe until the tube connector makes a "click" sound.
Install the fuel pipe clamp.
| 11. INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY LH |
![]() |
Set a new gasket to the LH cylinder head with the oval shape facing forward.
Install the exhaust manifold with the 6 nuts. Tighten the nuts uniformly in several steps.
Connect the air fuel ratio sensor connector.
| 12. INSTALL MANIFOLD STAY |
Install the manifold stay with the 3 bolts.
| 13. INSTALL NO.2 EXHAUST PIPE ASSEMBLY |
| 14. INSTALL NO.1 COOL AIR INLET |
Install the cool air inlet with the 2 bolts.
| 15. INSTALL CHAIN TENSIONER SLIPPER |
| 16. INSTALL NO.1 CHAIN TENSIONER ASSEMBLY |
![]() |
While turning the stopper plate of the tensioner clockwise, push in the plunger of the tensioner as shown in the illustration.
While turning the stopper plate of the tensioner counterclockwise, insert a bar of φ 35 mm (0.138 in.) into the holes in the stopper plate and tensioner to fix the stopper plate.
Install the chain tensioner with the 2 bolts.
| 17. INSTALL CHAIN SUB-ASSEMBLY |
| 18. INSTALL TIMING CHAIN OR BELT COVER SUB-ASSEMBLY |
| 19. INSTALL DIFFERENTIAL CARRIER ASSEMBLY FRONT (for 4WD) |
| 20. INSTALL POWER STEERING LINK ASSEMBLY |
| 21. INSTALL BATTERY |
| 22. ADD ENGINE OIL |
Fill with fresh engine oil.
| Oil grade | Oil viscosity (SAE) |
| ILSAC multigrade engine oil | 5W-30 |
| Item | Specified Condition |
| Drain and refill with oil filter change | 4.5 liters (4.8 US qts, 4.0 lmp. qts) |
| Drain and refill without oil filter change | 4.2 liters (4.4 US qts, 3.7 lmp. qts) |
| Dry fill | 5.6 liters (5.9 US qts, 4.9 lmp. qts) |
| Item | Specified Condition |
| Drain and refill with oil filter change | 5.2 liters (5.5 US qts, 4.6 lmp. qts) |
| Drain and refill without oil filter change | 4.9 liters (5.2 US qts, 4.3 lmp. qts) |
| Dry fill | 6.0 liters (6.3 US qts, 5.3 lmp. qts) |
Reinstall the oil filler cap.
| 23. ADD ENGINE COOLANT |
Pour coolant into the radiator until it overflows.
| Transmission | Capacity |
| Manual Transmission | 9.7 liters (10.3 Us qts, 8.5 Imp. qts) |
| Automatic Transmission | 9.8 liters (10.4 Us qts, 8.6 Imp. qts) |
Check the coolant level inside the radiator by squeezing the inlet and outlet radiator hoses several times by hand. If the coolant level goes down, add coolant.
Install the radiator cap securely.
Slowly pour coolant into the radiator reservoir until it reaches the FULL line.
Warm up the engine until the cooling fan operates.
Set the air conditioning as follows while warming up the engine.
| Item | Condition |
| Fan Speed | Any setting except OFF |
| Temperature | Toward WARM |
| Air Conditioning Switch | OFF |
Maintain the engine speed at 2,000 to 2,500 rpm and warm up the engine until the cooling fan operates.
Squeeze the inlet and outlet radiator hoses several times by hand while warming up the engine.
Stop the engine and wait until the coolant cools down.
Remove the radiator cap and check the coolant level inside the radiator.
If the coolant level is below the full level, perform the steps from (a) through (h) and repeat the operation until the coolant level remains at the full level.
Check the coolant level inside the radiator reservoir tank again. If it is below the full level, add coolant.
| 24. ADD DIFFERENTIAL OIL (for 4WD) |
| 25. INSPECT DIFFERENTIAL OIL (for 4WD) |
![]() |
Stop the vehicle on a level place.
Remove the differential filler plug and gasket.
Check that the oil level is within 5 mm (0 to 0.20 in.) of the bottom of the filler plug opening.
Check for oil leakage if the oil level is low.
Install the differential filler plug and a new gasket.
| 26. ADD POWER STEERING FLUID |
| 27. BLEED POWER STEERING FLUID |
Check the fluid level.
Jack up the front of the vehicle and support it with stands.
Turn the steering wheel.
With the engine stopped, turn the wheel slowly from lock to lock several times.
Lower the vehicle.
Start the engine.
Run the engine at idle for a few minutes.
Turn the steering wheel.
With the engine idling, turn the wheel to the left or right full lock position and keep it there for 2 to 3 seconds. Then turn the wheel to the opposite full lock position and keep it there for 2 to 3 seconds (step A).
Repeat step A several times.
Stop the engine.
![]() |
Check for foaming or emulsification.
Especially, if the system has to be bled twice because of foaming or emulsification, check for fluid leakage in the system.
Check the fluid level.
| 28. CHECK FOR ENGINE OIL LEAKAGE |
| 29. CHECK FOR ENGINE COOLANT LEAKAGE |
Fill the radiator with coolant and attach a radiator cap tester.
Pump it to 118 kPa (1.2 kgf/cm2 17.1 psi), then check for leakage.
| 30. CHECK FOR FUEL LEAKAGE |
| 31. CHECK FOR EXHAUST GAS LEAKAGE |
| 32. CHECK FOR POWER STEERING FLUID LEAKAGE |
| 33. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT |
| 34. INSPECT IGNITION TIMING |
Warm up the engine.
When using the Techstream.
Connect the Techstream to the DLC3.
Enter the following menu items:
Select: Powertrain / Engine and ECT / Data List / IGN Advance.
Inspect the ignition timing during idling.
Check that the ignition timing advances immediately when the engine speed is increased.
![]() |
When not using Techstream.
Using SST, connect the terminals 13 (TC) and 4 (CG) of the DLC3.
Remove the air cleaner.
![]() |
Pull out the wire harness as shown in the illustration.
Connect the tester probe of a timing light to the wire of the ignition coil connector for No. 1 cylinder.
![]() |
Inspect the ignition timing during idling.
Remove the SST from the DLC3.
Inspect the ignition timing during idling.
Install the air cleaner.
| 35. INSPECT ENGINE IDLING SPEED |
Warm up the engine.
When using the Techstream:
Connect the Techstream to the DLC3.
Enter the following menu items:
Select: Powertrain / Engine and ECT / Data List / Engine Speed.
Inspect the engine idling speed.
![]() |
When not using the Techstream:
Using SST, connect the terminal 8 (TAC) of the DLC3.
Race the engine speed at 2,500 rpm for approximately 90 seconds.
Inspect the engine idling speed.
| 36. INSPECT CO/HC |
Start the engine.
Run the engine at 2,500 rpm for approximately 180 seconds.
Insert the CO/HC meter testing probe at least 40 cm (1.3 ft) into the tailpipe during idling.
Immediately check the CO/HC concentration during idling and/or at 2,500 rpm.
If the CO/HC concentration does not comply with regulations, troubleshoot in the order given below.
Check the heated oxygen sensor operation.
| CO | HC | Problems | Causes |
| Normal | High | Rough idling |
|
| Low | High | Rough idling (Fluctuating HC reading) |
|
| High | High | Rough idling (Black smoke from exhaust) |
|
| 37. INSPECT COMPRESSION |
Warm up and stop the engine.
Remove the circuit opening relay.
Remove the V-bank cover.
Remove the air cleaner assembly.
Remove the ignition coils.
Remove the spark plugs.
![]() |
Inspect the cylinder compression pressure.
Insert a compression gage into the spark plug hole.
Fully open the throttle.
While cranking the engine, measure the compression pressure.
If the cylinder compression is low, pour a small amount of engine oil into the cylinder through the spark plug hole and repeat steps (1) through (3) for cylinders with low compression.