Home › ENGINE · 2TR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

SFI SYSTEM > VC Output Circuit

for Preparation Click here


DESCRIPTION

The ECM constantly generates 5 V power from the battery voltage supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.

A237333E01

When the VC circuit is short-circuited, the microprocessor in the ECM and sensors that are supplied power through the VC circuit are inactivated because the power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.

HINT:
Under normal conditions, the MIL is illuminated for several seconds when the ignition switch is first turned to ON. The MIL goes off when the engine is started.


WIRING DIAGRAM

Refer to the following pages.
  1. Throttle position sensor circuit .
  2. Canister pump module circuit .
  3. Secondary air injection pressure sensor circuit .
  4. Accelerator pedal circuit .

INSPECTION PROCEDURE

1.CHECK MIL
  1. Check that the Malfunction Indicator Lamp (MIL) lights up when turning the ignition switch to ON.

    OK:
    MIL lights up



OK
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)
NG


2.CHECK CONNECTION BETWEEN TECHSTREAM AND ECM
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream ON.

  1. Check the communication between the Techstream and ECM.
    Result 
    Result
    Proceed to
    Communication is possible
    A
    Communication is not possible
    B



A
GO TO MIL CIRCUIT (Click here)
B


3.CHECK MIL (THROTTLE BODY ASSEMBLY)
  1. Disconnect the throttle body assembly connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.
    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B



A
REPLACE THROTTLE BODY ASSEMBLY (Click here)
B


4.CHECK MIL (ACCELERATOR PEDAL SENSOR ASSEMBLY)
  1. Disconnect the accelerator pedal sensor assembly connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.
    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B



A
REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY (Click here)
B


5.CHECK MIL (AIR PRESSURE SENSOR FOR SECONDARY AIR INJECTION)
  1. Disconnect the air pressure sensor connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.
    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B



A
REPLACE AIR PRESSURE SENSOR
B


6.CHECK MIL (CANISTER PUMP MODULE)
  1. Disconnect the canister pump module connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.
    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B



A
REPLACE CANISTER PUMP MODULE (Click here)
B


7.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
  1. Disconnect the throttle body assembly connector.

  1. Disconnect the accelerator pedal sensor assembly connector.

  1. Disconnect the air pressure sensor connector.

  1. Disconnect the canister pump module connector.



    A079127E02
  1. Disconnect the ECM connector.

  1. Measure the resistance of the wire harness side connector.

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    VC (E4-18) - Body ground
    Always
    10 kΩ or higher
    VCPA (E8-26) - Body ground
    Always
    10 kΩ or higher
    VCP2 (E8-27) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)