Home › ENGINE · 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0724    Brake Switch "B" Circuit High

for Preparation Click here


DESCRIPTION

The stop light switch assembly is part of a duplex system that transmits 2 signals: STP and ST1-. These 2 signals are used by the ECM to monitor whether or not the brake system is working properly. This DTC indicates that the stop light switch assembly remains on. When the stop light switch remains on during GO and STOP driving, the ECM interprets this as a fault in the stop light switch. Then the MIL illuminates and the ECM stores the DTC.

DTC No.
DTC Detection Condition
Trouble Area
P0724
The stop light switch assembly remains ON even when the vehicle repeats 5 cycles of STOP (less than 3 km/h [1.86 mph]) and GO (30 km/h [18.64 mph] or more) (2 trip detection logic)
  1. Short in stop light switch signal circuit
  2. Stop light switch assembly
  3. ECM

MONITOR DESCRIPTION

This DTC indicates that the stop light switch assembly remains ON. When the stop light switch assembly remains ON during "STOP and GO" driving, the ECM interprets this as a fault in the stop light switch assembly and the MIL comes on and the ECM stores the DTC. The vehicle must stop (less than 3 km/h [1.86 mph]) and go (30 km/h [18.64 mph] or more) 5 times during 2 driving cycles, in order to detect a malfunction.

MONITOR STRATEGY


Related DTCs
P0724: Stop light switch/Range check/Rationality
Required sensors/Components (Main)
Stop light switch assembly
Required sensors/Components (Related)
Speed sensor
Frequency of Operation
Continuous
Duration
GO and STOP 5 times
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not stored
None
Battery voltage
8 V or higher
Starter
OFF
Ignition Switch
ON
GO: Vehicle speed
30 km/h (18.64 mph) or more
STOP: Vehicle speed
Less than 3 km/h (1.86 mph)

TYPICAL MALFUNCTION THRESHOLDS


Brake pedal position switch
ON stuck

CONFIRMATION DRIVING PATTERN


A199312E21

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on [A].
  6. Wait 5 seconds.
  7. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].
  8. Read pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  9. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  10. Input the DTC: P0724.
  11. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [C] through [E].

  12. Start the engine [C].
  13. Accelerate the vehicle to 30 km/h (18.64 mph) or more, depress the brake pedal and decelerate the vehicle to 3 km/h (1.86 mph) or less [D]. Repeat step [D] 5 times.

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  14. Check the DTC judgment result [E].
  15. If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM


E170557E03


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.READ VALUE USING TECHSTREAM (STOP LIGHT SWITCH)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Stop Light Switch.

  1. Read the values displayed on the Techstream.


OK:

Techstream Display
Measurement Item: Range (display)
Normal Condition
Stop Light Switch
Stop light switch status:
ON or OFF
  1. ON: Brake pedal is depressed
  2. OFF: Brake pedal is released



NG
Go to step 2
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

2.CHECK STOP LIGHT SWITCH ASSEMBLY INSTALLATION
  1. Check the stop light switch assembly installation (Click here).

    OK:
    Stop light switch assembly is installed correctly.



NG
SECURELY REINSTALL STOP LIGHT SWITCH ASSEMBLY
OK


3.INSPECT STOP LIGHT SWITCH ASSEMBLY
A115657E29
  1. Remove the stop light switch assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Switch pin not pushed
    Below 1 Ω
    Switch pin pushed
    10 kΩ or higher
    3 - 4
    Switch pin not pushed
    10 kΩ or higher
    Switch pin pushed
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Stop Light Switch Assembly)
    *b
    Not pushed
    *c
    Pushed



NG
REPLACE STOP LIGHT SWITCH ASSEMBLY
OK


4.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH - ECM)
  1. Disconnect the stop light switch assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    S10-1 - E14-18 (STP)
    Always
    Below 1 Ω
    S10-3 - E13-8 (ST1-)
    Always
    Below 1 Ω
    S10-1 or E14-18 (STP) - Body ground
    Always
    10 kΩ or higher
    S10-3 or E13-8 (ST1-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)