Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › OCCUPANT CLASSIFICATION SYSTEM (for Bench Seat Type)

DTC    B1773    Belt Tension Sensor Circuit Malfunction

DTC    B1776    Seat Belt Tension Sensor Power Source Circuit Malfunction

for Preparation Click here


DESCRIPTION

The belt tension sensor circuit consists of the occupant classification ECU and the belt tension sensor.
The belt tension sensor sends the belt tension signal to the occupant classification ECU to control the occupant classification system.
DTCs B1773 and B1776 are recorded when a malfunction is detected in the belt tension sensor circuit.

DTC No.
DTC Detecting Condition
Trouble Area
B1773
B1776
  1. Occupant classification ECU receives line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in belt tension sensor circuit for 2 seconds.
  2. Belt tension sensor malfunction
  3. Occupant classification ECU malfunction
  1. No. 1 seat wire
  2. Front seat outer belt RH (Belt tension sensor)
  3. Occupant classification ECU

HINT:
  1. When DTC B1650/32 is detected as a result of troubleshooting the supplemental restraint system, check the DTCs stored in the occupant classification ECU, and perform troubleshooting for those DTCs first.
  2. Use the Techstream to check for DTCs of the occupant classification ECU, otherwise the DTC cannot be read.


WIRING DIAGRAM


H101902E01


INSPECTION PROCEDURE

HINT:
  1. If troubleshooting (wire harness inspection) is difficult to perform, remove the passenger seat installation bolts to see the under surface of the seat cushion.
  2. In the above case, hold the seat so that it does not tip over. Holding the seat up for a long period of time may cause problems, such as seat rail deformation. Hold the seat up only for as long as necessary.

1.CHECK DTC
  1. Turn the ignition switch to the ON position.

  1. Clear the DTCs stored in the memory (Click here).

    HINT:
    First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor assembly.

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position.

  1. Check the DTCs (Click here).

    OK:
    DTC B1773 and B1776 are not output.

    HINT:
    DTCs other than B1773 and B1776 may be output at this time, but they are not related to this check.



OK
USE SIMULATION METHOD TO CHECK
NG


2.CHECK CONNECTORS
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the occupant classification ECU and the belt tension sensor.

    OK:
    The connectors are properly connected.

  1. Disconnect the connectors from the occupant classification ECU and the belt tension sensor.

  1. Check that the terminals of the connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK NO. 1 SEAT WIRE (TO B+)


    H101899E03
  1. Disconnect the connectors from the occupant classification ECU and belt tension sensor.

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    O10-8 (GBT) - Body ground
    Ignition switch ON
    Below 1 V
    O10-16 (BT) - Body ground
    Ignition switch ON
    Below 1 V
    O10-17 (VBT) - Body ground
    Ignition switch ON
    Below 1 V



NG
REPAIR OR REPLACE NO. 1 SEAT WIRE
OK


4.CHECK NO. 1 SEAT WIRE (FOR OPEN)


    H101903E01
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Using a service wire, connect S29-1 (BT) and S29-3 (GBT), and connect S29-2 (VBT) and S29-3 (GBT) of connector C.

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector when connecting.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    O10-16 (BT) - O10-8 (GBT)
    Always
    Below 1 Ω
    O10-17 (VBT) - O10-8 (GBT)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE NO. 1 SEAT WIRE
OK


5.CHECK NO. 1 SEAT WIRE (TO GROUND)


    H101899E03
  1. Disconnect the service wire from connector C.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    O10-8 (GBT) - Body ground
    Always
    1 MΩ or higher
    O10-16 (BT) - Body ground
    Always
    1 MΩ or higher
    O10-17 (VBT) - Body ground
    Always
    1 MΩ or higher



NG
REPAIR OR REPLACE NO. 1 SEAT WIRE
OK


6.CHECK NO. 1 SEAT WIRE (FOR SHORT)
H101899E03
  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    O10-16 (BT) - O10-8 (GBT)
    Always
    1 MΩ or higher
    O10-17 (VBT) - O10-8 (GBT)
    Always
    1 MΩ or higher



NG
REPAIR OR REPLACE NO. 1 SEAT WIRE
OK


7.CHECK DTC
  1. Connect the connectors to the occupant classification ECU and the belt tension sensor.

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch to the ON position.

  1. Clear the DTCs stored in the memory (Click here).

    HINT:
    First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor assembly.

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position.

  1. Check the DTCs (Click here).

    OK:
    DTCs B1773 and B1776 are not output.

    HINT:
    DTCs other than B1773 and B1776 may be output at this time, but they are not related to this check.



OK
USE SIMULATION METHOD TO CHECK
NG


8.REPLACE BELT TENSION SENSOR (FRONT SEAT OUTER BELT ASSEMBLY RH)
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Replace the belt tension sensor (Click here).

    HINT:
    Perform the inspection using parts from a normal vehicle if possible.

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch to the ON position.

  1. Clear the DTCs stored in the memory (Click here).

    HINT:
    First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor assembly.

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position.

  1. Check the DTCs (Click here).

    OK:
    DTCs B1773 and B1776 are not output.

    HINT:
    DTCs other than B1773 and B1776 may be output at this time, but they are not related to this check.



OK
END
NG


9.REPLACE OCCUPANT CLASSIFICATION ECU
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to the ON position.

  1. Store the occupant classification ECU data into the Techstream (Click here).

    HINT:
    If the ECU data cannot be stored in the Techstream, replace the front seat cushion assembly (with occupant classification ECU and occupant classification sensor).

  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Replace the occupant classification ECU (Click here).

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch to the ON position.

  1. Load the data from the previous ECU stored in the Techstream, into the newly installed ECU (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position.

  1. Clear the DTCs stored in the memory (Click here).

    HINT:
    If DTC is not cleared at this time, past DTC will remain.


NEXT


10.PERFORM SENSITIVITY CHECK
  1. Perform the sensitivity check (Click here).


NEXT

END