DTC B1791 Collision Detection Signal Line Malfunction |
| DTC No. | DTC Detections Conditions | Trouble Areas |
| B1791 |
|
|

| 1.CHECK DTC |
Turn the ignition switch to the ON position.
Clear any DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position.
Check the DTCs (Click here).
|
| ||||
| NG | |
| 2.CHECK CONNECTORS |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connectors are properly connected to the occupant classification ECU and the center airbag sensor assembly.
Disconnect the connectors from the occupant classification ECU and center airbag sensor assembly.
Check that the terminals of the connectors are not damaged.
|
| ||||
| OK | |
| 3.CHECK CENTER AIRBAG SENSOR ASSEMBLY COMMUNICATION CIRCUIT (TO B+) |
![]() |
Disconnect the connectors from the occupant classification ECU and center airbag sensor assembly.
Connect the negative (-) terminal cable to the battery.
Turn the ignition switch to the ON position.
Measure the voltage.
| Tester Connection | Condition | Specified Condition |
| A21-24 (GSW3) - Body ground | Ignition switch ON | Below 1 V |
|
| ||||
| OK | |
| 4.CHECK CENTER AIRBAG SENSOR ASSEMBLY COMMUNICATION CIRCUIT (FOR OPEN) |
![]() |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| A21-24 (GSW3) - O10-1 (GSW4) | Always | Below 1 Ω |
|
| ||||
| OK | |
| 5.CHECK CENTER AIRBAG SENSOR ASSEMBLY COMMUNICATION CIRCUIT (TO GROUND) |
![]() |
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| A21-24 (GSW3) - Body ground | Always | 1 MΩ or higher |
|
| ||||
| OK | |
| 6.CHECK DTC |
Connect the connectors to the occupant classification ECU and the center airbag sensor assembly.
Connect the negative (-) terminal cable to the battery.
Turn the ignition switch to the ON position.
Clear any DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position.
Check the DTCs (Click here).
|
| ||||
| NG | |
| 7.REPLACE OCCUPANT CLASSIFICATION ECU |
Connect the Techstream to the DLC3.
Turn the ignition switch to the ON position.
Store the occupant classification ECU data into the Techstream (Click here).
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Replace the occupant classification ECU (Click here).
Connect the negative (-) terminal cable to the battery.
Turn the ignition switch to the ON position.
Load the data from the previous ECU stored in the Techstream, into the newly installed ECU (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position.
Clear the DTCs stored in the memory (Click here).
| NEXT | |
| 8.CHECK DTC |
Turn the ignition switch to the ON position.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position.
Check the DTCs (Click here).
|
| ||||
| NG | |
| 9.REPLACE CENTER AIRBAG SENSOR ASSEMBLY |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Replace the center airbag sensor assembly (Click here).
| NEXT | |
| 10.PERFORM SENSITIVITY CHECK |
Perform the sensitivity check (Click here).
| NEXT | ||
| ||
| 11.CHECK CENTER AIRBAG SENSOR ASSEMBLY COMMUNICATION CIRCUIT (TO B+) |
![]() |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect the No. 1 seat wire connector from the floor wire.
Connect the negative (-) terminal cable to the battery and wait for at least 2 seconds.
Turn the ignition switch to the ON position.
Measure the voltage.
| Tester Connection | Condition | Specified Condition |
| A21-24 (GSW3) - Body ground | Ignition switch ON | Below 1 V |
|
| ||||
| OK | ||
| ||
| 12.CHECK CENTER AIRBAG SENSOR ASSEMBLY COMMUNICATION CIRCUIT (FOR OPEN) |
![]() |
Disconnect the No. 1 seat wire connector from the floor wire.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| A21-24 (GSW3) - BJ2-9 (GSW4) | Always | Below 1 Ω |
|
| ||||
| OK | ||
| ||
| 13.CHECK CENTER AIRBAG SENSOR ASSEMBLY COMMUNICATION CIRCUIT (TO GROUND) |
![]() |
Disconnect the No. 1 seat wire connector from the floor wire.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| A21-24 (GSW3) - Body ground | Always | 1 MΩ or higher |
|
| ||||
| OK | ||
| ||
| 14.CHECK INSTRUMENT PANEL WIRE (TO B+) |
![]() |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect the floor wire connector from the instrument panel wire.
Connect the negative (-) terminal cable to the battery and wait for at least 2 seconds.
Turn the ignition switch to the ON position.
Measure the voltage.
| Tester Connection | Condition | Specified Condition |
| A21-24 (GSW3) - Body ground | Ignition switch ON | Below 1 V |
|
| ||||
| OK | ||
| ||
| 15.CHECK INSTRUMENT PANEL WIRE (FOR OPEN) |
![]() |
Disconnect the floor wire connector from the instrument panel wire.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| A21-24 (GSW3) - IL1-3 (GSW4) | Always | Below 1 Ω |
|
| ||||
| OK | ||
| ||
| 16.CHECK INSTRUMENT PANEL WIRE (TO GROUND) |
![]() |
Disconnect the floor wire connector from the instrument panel wire.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| A21-24 (GSW3) - Body ground | Always | 1 MΩ or higher |
|
| ||||
| OK | ||
| ||