DTC P050B Cold Start Ignition Timing Performance |

| DTC No. | DTC Detection Condition | Trouble Area |
| P050B | Insufficient ignition timing retard at cold start (2 trip detection logic) |
|
| Related DTCs | P050B: Cold start ignition timing performance |
| Required Sensors / Components (Main) | Throttle with motor body assembly |
| Required Sensors / Components (Related) | Mass air flow meter sub-assembly Engine coolant temperature sensor |
| Frequency of Operation | Once per driving cycle |
| Duration | 10 seconds |
| MIL Operation | 2 driving cycles |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not stored | P0010, P0020 (Camshaft timing oil control valve) P0011, P0021 (VVT system - advance) P0012, P0022 (VVT System - retard) P0016, P0018 (VVT system - misalignment) P0102, P0103 (Mass air flow meter) P0115, P0117, P0118 (Engine coolant temperature sensor) P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor) P0125 (Insufficient coolant temperature for closed loop fuel control) P014C, P014D, P014E, P014F, P015A, P015B, P015C, P015D, P2195, P2196, P2197, P2198, P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255, P2256 (Air fuel ratio sensor) P0171, P0172, P0174, P0175 (Fuel system) P0301, P0302, P0303, P0304, P0305, P0306 (Misfire) P0335 (Crankshaft position sensor) P0340, P0342, P0343, P0345, P0347, P0348 (VVT sensor) P0351, P0352, P0353, P0354, P0355, P0356 (Igniter) P0500 (Vehicle speed sensor) P0705 (Shift lever position switch) P219A, P219B (Air-fuel ratio imbalance) |
| Battery voltage | 8 V or more |
| Time after engine start | 3 seconds or more |
| Starter | OFF |
| Engine coolant temperature at engine start | -10°C (14°F) or more |
| Engine coolant temperature | -10°C (14°F) or higher, and less than 50°C (122°F) |
| Fuel-cut | OFF |
| Engine idling time | 3 seconds or more |
| Vehicle speed | Less than 3 km/h (1.875 mph) |
| Atmospheric pressure | 76 kPa(abs) [570 mmHg(abs)] or more |
| Accumulated time when ignition timing retard value is cut off | 5 seconds or more |
| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| Symptom | Factor | Trouble Area |
| Low idle speed when engine is cold (immediately after engine start) | Excessive engine friction |
|
| Rough idle when engine is cold (immediately after engine start) | Abnormal combustion |
|
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P050B) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
| Result | Proceed To |
| DTC P050B is output | A |
| DTC P050B and other DTCs are output | B |
|
| ||||
| A | |
| 2.READ VALUE USING TECHSTREAM (FUEL TRIM) |
Connect the Techstream to the DLC3.
Start the engine.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Short FT #1 and Long FT #1, or Short FT #2 and Long FT #2.
Read the values displayed on the Techstream at engine idle.
Add together the Short FT #1 and Long FT #1, or Short FT #2 and Long FT #2 values to obtain the total Fuel Trim
|
| ||||
| OK | |
| 3.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY (THROTTLE VALVE) |
Inspect that there are no deposits around the throttle valve and throttle valve condition.
|
| ||||
|
| ||||
| 4.REPAIR OR REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY |
Repair or replace the throttle with motor body assembly (Click here).
|
| ||||
| 5.CHECK PCV SYSTEM |
Check the PCV hose connections (Click here).
|
| ||||
| OK | |
| 6.CHECK INTAKE SYSTEM |
Check the intake system for vacuum leaks.
|
| ||||
| OK | |
| 7.CHECK AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY |
Visually check that the air cleaner filter element sub-assembly is not excessively contaminated with dirt or oil.
|
| ||||
| OK | |
| 8.PERFORM ACTIVE TEST USING TECHSTREAM (OPERATE CAMSHAFT TIMING OIL CONTROL VALVE) |
Connect the Techstream to the DLC3.
Start the engine.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Linear (Bank 1) or Control the VVT Linear (Bank 2).
Check the engine speed while operating the camshaft timing oil control valve assembly using the Techstream.
| Techstream Operation | Specified Condition |
| 0% | Normal engine speed |
| 100% | Engine idles roughly or stalls |
|
| ||||
| OK | |
| 9.READ VALUE USING TECHSTREAM (MAF) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / MAF, Coolant Temp and Engine Speed.
Read MAF with the engine speed at 2000 rpm.
| Techstream Display | Condition | Specified Condition |
| MAF | Shift lever position: N (Neutral) A/C: Off Engine Speed: 2000 rpm | Between 13.1 gm/sec. and 18.9 gm/sec |
|
| ||||
|
| ||||
| 10.REPAIR OR REPLACE PCV SYSTEM |
Repair or replace the PCV valve or hose.
|
| ||||
| 11.REPAIR OR REPLACE INTAKE SYSTEM |
Repair or replace the intake system.
|
| ||||
| 12.REPLACE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY |
Replace air cleaner filter element sub-assembly.
|
| ||||
| 13.CHECK AND REPAIR VVT SYSTEM |
Check and repair the VVT system.
| NEXT | |
| 14.CHECK WHETHER DTC OUTPUT RECURS (DTC P050B) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the Techstream on.
) Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.
Check that the engine coolant temperature is between -10°C and 50°C (14 and 122°F).
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P050B.
Check the DTC judgment result.
| Result | Proceed to |
| NORMAL (DTC is not output) | A |
| ABNORMAL (DTC P050B is output) | B |
|
| ||||
| A | ||
| ||
| 15.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY CONNECTOR CONNECTION) |
Check the connection and terminal contact pressure of connectors and wire harnesses between the mass air flow meter sub-assembly and ECM (Click here).
| NEXT | |
| 16.CHECK WHETHER DTC OUTPUT RECURS (DTC P050B) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.
Check that the engine coolant temperature is between -10°C and 50°C (14 and 122°F).
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P050B.
Check the DTC judgment result.
| Result | Proceed to |
| ABNORMAL (DTC P050B is output) | A |
| NORMAL (DTC is not output) | B |
|
| ||||
| A | |
| 17.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM) |
Disconnect the mass air flow meter sub-assembly.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| M1-3 (VG) - E10-14 (VG) | Always | Below 1 Ω |
| M1-2 (E2G) - E10-13 (E2G) | Always | Below 1 Ω |
| M1-3 (VG) or E10-14 (VG) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 18.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY |
Replace the mass air flow meter sub-assembly.
| NEXT | |
| 19.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.
Check that the engine coolant temperature is between -10°C and 50°C (14 and 122°F).
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P050B.
Check the DTC judgment result.
| Result | Proceed to |
| NORMAL (DTC is not output) | A |
| ABNORMAL (DTC P050B is output) | B |
|
| ||||
| A | ||
| ||