Home › BRAKE › BRAKE CONTROL › VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)

VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster) > Brake Warning Light Remains ON

for Preparation Click here


DESCRIPTION

The BRAKE warning light comes on when brake fluid is insufficient, the parking brake is applied or the EBD is defective.

WIRING DIAGRAM


C237280E02


INSPECTION PROCEDURE

NOTICE:
  1. When replacing the skid control ECU (master cylinder solenoid), perform calibration (Click here).
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK THAT SKID CONTROL ECU CONNECTOR SECURELY CONNECTED
  1. Check the skid control ECU (master cylinder solenoid) connector connection.

    OK:
    The connector is securely connected.



NG
CONNECT CONNECTOR TO ECU CORRECTLY
OK


2.CHECK DTC
  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
REPAIR CIRCUITS INDICATED BY OUTPUT DTCS (Click here)
A


3.INSPECT BATTERY
  1. Inspect the battery voltage (Click here).

    Standard voltage:
    11 to 14 V



NG
CHECK CHARGING SYSTEM (Click here)
OK


4.CHECK BRAKE FLUID LEVEL
  1. Turn the ignition switch off.

  1. Depress the brake pedal 20 times or more (until the pedal reaction feels light and pedal stroke becomes longer).

  1. Check the amount of fluid in the brake reservoir.

    HINT:
    When the ignition switch is turned to ON, brake fluid is sent to the accumulator and the fluid level decreases by approximately 5 mm (0.197 in.) from the level when the ignition switch is off (normal).

    OK:
    Brake fluid level is normal.



NG
CHECK AND REPAIR BRAKE FLUID LEAKAGE
OK


5.CHECK CAN COMMUNICATION LINE
  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Select CAN Bus Check from the System Selection Menu screen and follow the prompts on the screen to inspect the CAN bus (Click here).

    OK:
    CAN Bus Check indicates no malfunctions in CAN communication.



NG
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
OK


6.PERFORM ACTIVE TEST USING TECHSTREAM (Indicat. Lamp Brake)
  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Combination Meter / Active Test.

  1. According to the display on the Techstream, perform the Active Test.


Combination Meter 
Tester Display
Test Part
Control Range
Diagnostic Note
Indicat. Lamp Brake
Brake warning light
OFF/ON
Perform the test with the vehicle stopped and the engine idling
  1. Check that the BRAKE warning light on the combination meter assembly turns on or off in accordance with the Techstream operation.

    OK:
    The BRAKE warning light turns on or off in accordance with the Techstream operation.



NG
GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
OK


7.READ VALUE USING TECHSTREAM (Parking Brake SW)
  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Chassis / ABS/VSC/TRAC / Data List.

    ABS/VSC/TRAC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Parking Brake SW
    Parking brake switch/ ON or OFF
    ON: Parking brake applied
    OFF: Parking brake released
    -

  1. Using the Techstream, check the input of the switch operation when the parking brake pedal is operated.

    OK:
    When the parking brake is operated, the display changes as shown above.



NG
Go to step 12
OK


8.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)
  1. Disconnect the skid control ECU connector (master cylinder solenoid).



    C214161E55
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    S1-46 (IG1) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU (Master Cylinder Solenoid))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9.CHECK HARNESS AND CONNECTOR (GND TERMINAL)


    C124799E55
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S1-1 (GND1) - Body ground
    Always
    Below 1 Ω
    S1-32 (GND2) - Body ground
    Always
    Below 1 Ω
    S2-4 (GND3) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU (Master Cylinder Solenoid))

  1. Reconnect the skid control ECU (master cylinder solenoid) connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10.INSPECT BRAKE FLUID LEVEL WARNING SWITCH
  1. Disconnect the B2 brake fluid level warning switch (brake master cylinder reservoir sub-assembly) connector.



    C217215E14
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Float UP (Switch off)
    1.9 to 2.1 kΩ
    Float DOWN (Switch on)
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Brake Fluid Level Warning Switch (Brake Master Cylinder Reservoir Sub-assembly))



NG
REPLACE BRAKE MASTER CYLINDER SUB-ASSEMBLY (BRAKE FLUID LEVEL WARNING SWITCH) (Click here)
OK


11.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BRAKE FLUID LEVEL WARNING SWITCH)
  1. Disconnect the S1 skid control ECU (master cylinder solenoid) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S1-41 (LBL) - B2-2
    Always
    Below 1 Ω
    S1-41 (LBL) - Body ground
    Always
    10 kΩ or higher
    B2-1 (GND) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MASTER CYLINDER SOLENOID (Click here)  

12.INSPECT PARKING BRAKE SWITCH
  1. Disconnect the P6 parking brake switch connector.



    C237289E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - Body ground
    Parking brake applied
    (Switch pin not pushed in)
    Below 1 Ω
    Parking brake released
    (Switch pin pushed in)
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Parking Brake Switch)



NG
REPLACE PARKING BRAKE SWITCH
OK


13.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - PARKING BRAKE SWITCH)
  1. Disconnect the S1 skid control ECU (master cylinder solenoid) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    P6-1 - S1-28 (PKB)
    Always
    Below 1 Ω
    P6-1 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MASTER CYLINDER SOLENOID (Click here)