Home › COMMUNICATION SYSTEM › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > DIAGNOSIS SYSTEM

for Preparation Click here



BUS CHECK

HINT:
Only CAN communication system DTCs for each ECU can be displayed on the Techstream.

  1. Select "CAN Bus Check" from "System Select".


CHECK INSTALLED SYSTEMS (ECUS AND SENSORS) THAT USE CAN COMMUNICATION
  1. Systems (ECUs and sensors) that use CAN communication vary depending on the optional settings of the vehicle. Check which systems (ECUs and sensors) are installed on the vehicle.

    ECU/Sensor Name
    Techstream Display
    Check method
    Skid Control ECU
    ABS/VSC/TRAC
    installed on all vehicles
    Combination Meter Assembly
    Combination meter
    Installed on all vehicles
    ECM
    Engine
    Installed on all vehicles
    Center Airbag Sensor Assembly
    SRS Airbag
    Installed on all vehicles
    Steering Angle Sensor
    Steering Angle Sensor
    Installed on all vehicles
    Yaw Rate Sensor
    Yaw Rate / Deceleration Sensor
    Installed on all vehicles

    HINT:
    Vehicle with ABS do not use CAN communication.


DTC TABLE BY ECU

HINT:
  1. In the CAN communication system, CAN communication system DTCs output by the ECU can be displayed by using the Techstream.
  2. If CAN communication system DTCs are output, trouble cannot be determined solely from the DTCs. Perform troubleshooting according to "How To Proceed with Troubleshooting" (Click here).

  1. SKID CONTROL ECU

    HINT:
    DTC communication uses the SIL Line.


    DTC No.
    Detection Item
    U0073
    Control Module Communication Bus OFF
    U0100
    Lost Communication with ECM/PCM
    U0126
    Lost Communication with Steering Angle Sensor Module
    U0123
    Lost Communication with Yaw Rate Sensor Module
    U0124
    Lost Communication with Lateral Acceleration Sensor Module

  2. COMBINATION METER ASSEMBLY

    HINT:
    DTC communication uses the CAN communication system.


    DTC No.
    Detection Item
    U0100
    Lost Communication with ECM/PCM
    U0129
    Lost Communication with Skid Control ECU
    U0151
    Lost Communication with Airbag ECU

  3. YAW RATE AND DECELERATION SENSOR

    HINT:
    1. The yaw rate and deceleration sensor is connected to the CAN communication system but CAN communication DTCs are not output.
    2. If "Yaw Rate/Deceleration Sensor" is not displayed on the "Bus Check" screen on the Techstream, proceed to "Yaw Rate Sensor Communication Stop Mode" (Click here).

  4. STEERING ANGLE SENSOR

    HINT:
    1. The steering angle sensor is connected to the CAN communication system but CAN communication DTCs are not output.
    2. If "Steering Sensor" is not displayed on the "Bus Check" screen on the Techstream, proceed to "Steering Angle Sensor Communication Stop Mode" (Click here).

  5. ECM

    HINT:
    1. The ECM is connected to the CAN communication system but CAN communication DTCs are not output.
    2. If "Engine" is not displayed on the "Bus Check" screen on the Techstream, proceed to "ECM Communication Stop Mode" (Click here).

  6. CENTER AIRBAG SENSOR ASSEMBLY

    HINT:
    1. The center airbag sensor assembly is connected to the CAN communication system but CAN communication DTCs are not output.
    2. If "SRS Airbag " is not displayed on the "Bus Check" screen on the Techstream, proceed to "Center Airbag Sensor Communication Stop Mode" (Click here).


DTC COMBINATION TABLE

Output from
Output DTC
Detected Communication Stop Mode
V-Bus
ECM Communication Stop Mode
Skid Control ECU Communication Stop Mode
Yaw Rate Sensor Communication Stop Mode
Steering Angle Sensor Communication Stop Mode
Center Airbag Sensor Communication Stop Mode
Combination Meter ECU Communication Stop Mode
Skid Control ECU
U0073
X
○*1
X
X
X
X
U0100
○
○*1
X
X
X
X
U0126
X
○*1
X
○
X
X
U0123
X
○*1
○
X
X
X
U0124
X
○*1
○
X
X
X
Combination Meter ECU
U0100
○
X
X
X
X
○*1
U0129
X
○
X
X
X
○*1
U0151
X
X
X
X
○
○*1

HINT:
  1. ○:Stored.
  2. X: When one side of branch wire is open, storage may occur.
  3. *1: DTC may not be output when the CAN communication system malfunctions.

  1. Perform troubleshooting according to the combination of DTCs output.

    HINT:
    1. Skid Control ECU Communication Stop Mode: (Click here)
    2. Steering Angle Sensor Communication Stop Mode: (Click here)
    3. Yaw Rate Sensor Communication Stop Mode: (Click here)
    4. ECM Communication Stop Mode: (Click here)
    5. Combination Meter ECU Communication Stop Mode: (Click here)
    6. Center Airbag Sensor Communication Stop Mode: (Click here)