Home › BRAKE › BRAKE CONTROL › VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)

VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster) > Slip Indicator Light Remains ON

for Preparation Click here


DESCRIPTION

The slip indicator light blinks during VSC or TRAC and AUTO LSD operation. When the system fails, the slip indicator light comes on to warn the driver.

WIRING DIAGRAM


C237282E02


INSPECTION PROCEDURE

NOTICE:
  1. When replacing the skid control ECU (master cylinder solenoid), perform calibration (Click here)
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK THAT SKID CONTROL ECU CONNECTOR SECURELY CONNECTED
  1. Check the skid control ECU (master cylinder solenoid) connector connection.

    OK:
    The connector is securely connected.



NG
CONNECT CONNECTOR TO ECU CORRECTLY
OK


2.CHECK DTC
  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
REPAIR CIRCUITS INDICATED BY OUTPUT DTCS (Click here)
A


3.INSPECT BATTERY
  1. Inspect the battery voltage (Click here).

    Standard voltage:
    11 to 14 V



NG
CHECK CHARGING SYSTEM (Click here)
OK


4.CHECK CAN COMMUNICATION LINE
  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Select CAN Bus Check from the System Selection Menu screen and follow the prompts on the screen to inspect the CAN bus (Click here).

    OK:
    CAN Bus Check indicates no malfunctions in CAN communication.



NG
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
OK


5.PERFORM ACTIVE TEST USING TECHSTREAM (Indicat. Lamp Slip)
  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Combination Meter / Active Test.

  1. According to the display on the Techstream, perform the Active Test.


Combination Meter 
Tester Display
Test Part
Control Range
Diagnostic Note
Indicat. Lamp Slip
Slip indicator light
OFF/ON
Perform the test with the vehicle stopped and the engine idling
  1. Check that the Slip indicator light on the combination meter assembly turns on or off in accordance with the Techstream operation.

    OK:
    The Slip indicator light turns on or off in accordance with the Techstream operation.



NG
GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
OK


6.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)
  1. Disconnect the skid control ECU (master cylinder solenoid) connector.



    C214161E55
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    S1-46 (IG1) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU (Master Cylinder Solenoid))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.CHECK HARNESS AND CONNECTOR (GND TERMINAL)


    C124799E55
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S1-1 (GND1) - Body ground
    Always
    Below 1 Ω
    S1-32 (GND2) - Body ground
    Always
    Below 1 Ω
    S2-4 (GND3) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU (Master Cylinder Solenoid))

  1. Reconnect the skid control ECU (master cylinder solenoid) connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MASTER CYLINDER SOLENOID (Click here)