Home › BRAKE › BRAKE CONTROL › VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)

VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster) > AUTO LSD Indicator Light does not Come ON

for Preparation Click here


DESCRIPTION

The AUTO LSD does not operate even if the VSC OFF switch is pressed under the following conditions:
  1. The brake system is faulty.
  2. The temperature inside the hydraulic brake booster increases and the AUTO LSD operation is suspended.
  3. The rear differential is locked.

WIRING DIAGRAM


C237290E03


INSPECTION PROCEDURE

NOTICE:
  1. When replacing the skid control ECU (master cylinder solenoid), perform calibration (Click here).
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK CAN COMMUNICATION LINE
  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Select CAN Bus Check from the System Selection Menu screen and follow the prompts on the screen to inspect the CAN bus (Click here).

    OK:
    CAN Bus Check indicates no malfunctions in CAN communication.



NG
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
OK


2.CHECK DTC
  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
REPAIR CIRCUITS INDICATED BY OUTPUT DTCS (Click here)
A


3.PERFORM ACTIVE TEST USING TECHSTREAM (indicat. AUTO LSD)
  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Combination Meter / Active Test.

  1. According to the display on the Techstream, perform the Active Test.


Combination Meter 
Tester Display
Test Part
Control Range
Diagnostic Note
Indicat. Auto LSD
AUTO LSD indicator light
OFF/ON
Perform the test with the vehicle stopped and the engine idling
  1. Check that the AUTO LSD indicator light on the combination meter assembly turns on or off in accordance with the Techstream operation.

    OK:
    The AUTO LSD indicator light turns on or off in accordance with the Techstream operation.



NG
GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (CSW TERMINAL)
  1. Disconnect the S1 skid control ECU (master cylinder solenoid) connector.



    C214161E65
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    S1-9 (CSW) - Body ground
    VSC OFF switch not pushed in
    10 kΩ or higher
    VSC OFF switch pushed in
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU)

  1. Reconnect the S1 skid control ECU (master cylinder solenoid) connector.



NG
Go to step 6
OK


5.CHECK HARNESS AND CONNECTOR (EXI3 TERMINAL)
  1. Set the vehicle in the rear differential free state using the differential lock switch.

  1. Disconnect the skid control ECU (master cylinder solenoid) connector.



    C214161E63
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    S1-40 (EXI3) - Body ground
    Ignition switch ON
    Rear differential free
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU (Master Cylinder Solenoid))



NG
Go to step 7
OK

REPLACE MASTER CYLINDER SOLENOID (Click here)  

6.INSPECT VSC OFF SWITCH
  1. Remove the VSC OFF switch (Click here).



    C237120E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    3 - 4
    Switch is not pushed
    10 kΩ or higher
    Switch is pushed
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (VSC OFF Switch)



NG
REPLACE VSC OFF SWITCH (Click here)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR 

7.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU EXI3 CIRCUIT)
  1. Disconnect the S1 skid control ECU (master cylinder solenoid) connector.

  1. Disconnect the F12 4 wheel drive control ECU connector.

  1. Disconnect the C10 combination meter assembly connector.

  1. Disconnect the T13 differential lock indicator switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S1-40 (EXI3) - F12-20 (RLP)
    Always
    Below 1 Ω
    S1-40 (EXI3) - C10-14
    Always
    Below 1 Ω
    S1-40 (EXI3) - T13-2
    Always
    Below 1 Ω
    T13-1 - Body ground
    Always
    Below 1 Ω
    S1-40 (EXI3) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.INSPECT DIFFERENTIAL LOCK INDICATOR SWITCH
  1. Remove the differential lock indicator switch.



    C214518E04
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    2 - 1
    Pushed in
    Below 1 Ω
    Not pushed in
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Differential Lock Indicator Switch)



NG
REPLACE DIFFERENTIAL LOCK INDICATOR SWITCH
OK


9.REPLACE 4 WHEEL DRIVE CONTROL ECU
  1. Replace the 4 wheel drive control ECU.

  1. Reconnect the S1 skid control ECU (master cylinder solenoid) connector.

  1. Turn the ignition switch to ON.

  1. Check that pressing the VSC OFF switch causes the AUTO LSD indicator light to come on.

    OK:
    AUTO LSD indicator light comes on.



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK

END