Home › BRAKE › BRAKE CONTROL › VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)

VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster) > A-TRAC Indicator Light does not Come ON

for Preparation Click here


DESCRIPTION

The A-TRAC does not operate even if the A-TRAC switch is pressed under the following conditions:
  1. The TRAC or VSC system is faulty.
  2. The temperature inside the hydraulic brake booster increases and the A-TRAC operation is suspended.

WIRING DIAGRAM

Refer to A-TRAC Indicator Light Remains ON .

INSPECTION PROCEDURE

NOTICE:
When replacing the skid control ECU (master cylinder solenoid), perform calibration (Click here).

1.CHECK CAN COMMUNICATION LINE
  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Select CAN Bus Check from the System Selection Menu screen and follow the prompts on the screen to inspect the CAN bus (Click here).

    OK:
    CAN Bus Check indicates no malfunctions in CAN communication.



NG
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
OK


2.PERFORM ACTIVE TEST USING TECHSTREAM (ACTIVE TRC Indicator)
  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Combination Meter / Active Test.

  1. According to the display on the Techstream, perform the Active Test.


Combination Meter 
Tester Display
Test Part
Control Range
Diagnostic Note
ACTIVE TRC Indicator
A-TRAC indicator light
OFF/ON
Perform the test with the vehicle stopped and the engine idling
  1. Check that the A-TRAC indicator light on the combination meter assembly turns on or off in accordance with the Techstream operation.

    OK:
    The A-TRAC indicator light turns on or off in accordance with the Techstream operation.



NG
GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (ATRC TERMINAL)
  1. Disconnect the S1 skid control ECU (master cylinder solenoid) connector.



    C214161E64
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    S1-13 (ATRC) - Body ground
    A-TRAC switch not pushed in
    10 kΩ or higher
    A-TRAC switch pushed in
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU (Master Cylinder Solenoid))

  1. Reconnect the S1 skid control ECU (master cylinder solenoid) connector.



NG
Go to step 4
OK

REPLACE MASTER CYLINDER SOLENOID (Click here)  

4.INSPECT A-TRAC SWITCH
  1. Remove the A-TRAC switch (Click here).



    C237117E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    5 - 8
    Switch is not pushed
    Below 1 Ω
    Switch is pushed
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (A-TRAC Switch)



NG
REPLACE A-TRAC SWITCH (Click here)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR