Home › BRAKE › BRAKE CONTROL › VEHICLE STABILITY CONTROL SYSTEM

DTC    C0210/33    Right Rear Wheel Speed Sensor Signal

DTC    C0215/34    Left Rear Wheel Speed Sensor Signal

DTC    C1273/73    Low Output Signal of Rear Speed Sensor RH (Test Mode DTC)

DTC    C1274/74    Low Output Signal of Rear Speed Sensor LH (Test Mode DTC)

DTC    C1277/77    Abnormal Change in Output Signal of Rear Speed Sensor RH (Test Mode DTC)

DTC    C1278/78    Abnormal Change in Output Signal of Rear Speed Sensor LH (Test Mode DTC)

DTC    C1332/37    Open Circuit in Right Rear Wheel Speed Sensor Circuit

DTC    C1333/38    Open Circuit in Left Rear Wheel Speed Sensor Circuit

for Preparation Click here


DESCRIPTION

Refer to DTC C0200/31 (Click here).

DTC Code
DTC Detection Condition
Trouble Area
C0210/33
C0215/34
When any of following conditions detected:
  1. When vehicle speed 15 km/h (9 mph), wheel speed 6 km/h (4 mph).
  2. At vehicle speed of 45 km/h (28 mph) or more, open in sensor harness occurs intermittently for 0.2 seconds or more.
  3. When vehicle speed between 10 km/h (6 mph) and 15 km/h (9 mph) for 3 minutes, one wheel speed 0 km/h (0 mph).
  4. Pressure reduction mode of ABS system lasts for 28 seconds or more.
  5. When vehicle driven at speed of 20 km/h (12 mph) or more, difference between wheel speeds indicated by two sensors occurs twice or more for 30 seconds or more.
  6. Foreign matter adheres to sensor rotor.
  1. Rear speed sensor
  2. Rear speed sensor circuit
  3. Sensor installation
  4. Foreign matter on sensor rotor
C1273/73
C1274/74
Detected only during test mode.
  1. Rear speed sensor
  2. Rear speed sensor circuit
  3. Sensor installation
  4. Foreign matter on sensor rotor
C1277/77
C1278/78
Detected only during test mode.
  1. Rear speed sensor (open)
  2. Rear speed sensor circuit (open)
C1332/37
C1333/38
Open in rear speed sensor circuit continues for 0.15 seconds or more.
  1. Rear speed sensor (open)
  2. Rear speed sensor circuit (open)

HINT:
  1. DTCs C0210/33 and C1332/37 are for the rear speed sensor RH.
  2. DTCs C0215/34 and C1333/38 are for the rear speed sensor LH.


WIRING DIAGRAM


C159469E02


INSPECTION PROCEDURE

NOTICE:
  1. When replacing the VSC actuator assembly, perform zero point calibration (Click here).
  2. Check the speed sensor signal in test mode after cleaning or replacement (Click here).

1.READ VALUE USING TECHSTREAM (REAR SPEED SENSOR)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Select the Data List mode on the Techstream.

    ABS/VSC/TRAC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    RL Wheel Speed
    Rear wheel speed sensor LH reading /
    min.: 0 km/h (0 mph), max.: 326.4 km/h (202 mph)
    Actual wheel speed
    Similar speed as indicated on speedometer
    RR Wheel Speed
    Rear wheel speed sensor RH reading /
    min.: 0 km/h (0 mph), max.: 326.4 km/h (202 mph)
    Actual wheel speed
    Similar speed as indicated on speedometer

  1. Check that the speed value output from the speed sensor displayed on the Techstream and the speed value displayed on the speedometer are almost the same when driving the vehicle.

    OK:
    The speed value output from the speed sensor displayed on the Techstream is the same as the actual vehicle speed.

    HINT:
    There is a tolerance of +/-10% in the speedometer indication.



NG
Go to step 4
OK


2.PERFORM TEST MODE INSPECTION (SIGNAL CHECK)
  1. Perform a TEST MODE inspection and check for DTCs (Click here).

    OK:
    No DTCs output.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (SPEED SENSOR CIRCUIT)
OK


3.RECONFIRM DTC
  1. Clear the DTC(s) (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.

  1. Check if the same DTC(s) is output (Click here).
    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
Go to step 10
A

USE SIMULATION METHOD TO CHECK (Click here)  

4.CHECK REAR SPEED SENSOR INSTALLATION


    I044006E06
  1. Check that the speed sensor installation bolt is tightened properly.

    Torque:
    11 N*m (107 kgf*cm, 8 ft.*lbf)

    OK:
    The installation bolt is tightened properly.



NG
TIGHTEN BOLT PROPERLY
OK


5.CHECK REAR SPEED SENSOR
  1. Visually check the speed sensor for deformation and damage.

    OK:
    No deformation or damage.
    There is no gap between the sensor and rear axle carrier.



NG
REPLACE REAR SPEED SENSOR
OK


6.CHECK SPEED SENSOR TIP
  1. Remove the speed sensor (Click here).

  1. Check the sensor tip.

    OK:
    No scratches or foreign matter on the sensor tip.



NG
CLEAN OR REPLACE SPEED SENSOR
OK


7.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - REAR SPEED SENSOR)


    C152718E02
  1. Confirm that the skid control ECU connector and speed sensor connector are properly connected.

  1. Disconnect the A17 ECU connector.

  1. Disconnect the b3 and b4 sensor connectors.

  1. Inspect both the connector case and the terminal for deformation and corrosion.

    OK:
    No deformation or corrosion.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH:
    Tester Connection
    Condition
    Specified Condition
    A17-36 (RR+) - b3-2 (RR+)
    Always
    Below 1 Ω
    A17-37 (RR-) - b3-1 (RR-)
    A17-36 (RR+) - Body ground
    Always
    10 kΩ or higher
    A17-37 (RR-) - Body ground

    for LH:
    Tester Connection
    Condition
    Specified Condition
    A17-43 (RL+) - b4-2 (RL+)
    Always
    Below 1 Ω
    A17-42 (RL-) - b4-1 (RL-)
    A17-43 (RL+) - Body ground
    Always
    10 kΩ or higher
    A17-42 (RL-) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (SPEED SENSOR CIRCUIT)
OK


8.CHECK REAR SPEED SENSOR (INPUT VOLTAGE)


    C152719E02
  1. Reconnect the A17 ECU connector.

  1. Disconnect the b3 and b4 sensor connectors.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    b3-2 (RR+) - Body ground
    Ignition switch ON
    5.5 to 20 V
    b4-2 (RL+) - Body ground



NG
REPLACE VSC ACTUATOR ASSEMBLY (Click here)
OK


9.RECONFIRM DTC
  1. Clear the DTC(s) (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.

  1. Check if the same DTC(s) is output (Click here).
    Result 
    Result
    Proceed to
    DTC is output
    A
    DTC is not output
    B



B
USE SIMULATION METHOD TO CHECK (Click here)
A


10.REPLACE REAR SPEED SENSOR
  1. Replace the rear speed sensor (Click here).


NEXT


11.RECONFIRM DTC
  1. Clear the DTC(s) (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.

  1. Check if the same DTC(s) is output (Click here).
    Result 
    Result
    Proceed to
    DTC is output
    A
    DTC is not output
    B



B
END
A

REPLACE VSC ACTUATOR ASSEMBLY (Click here)