Home › ENGINE · 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

SFI SYSTEM > ACIS Control Circuit

for Preparation Click here


DESCRIPTION

This circuit opens and closes the Intake Air Control Valve (IACV) in response to changes in the engine load in order to increase the intake efficiency (ACIS: Acoustic Control Induction System).
When the engine speed is between 2200 rpm and 4100 rpm and the throttle valve opening angle is 60° or more, the ECM supplies current to the VSV (ON status), to close the IACV. Under other conditions, the VSV is usually OFF and the IACV is open.

A115903E02


WIRING DIAGRAM


A161384E01


INSPECTION PROCEDURE

1.PERFORM ACTIVE TEST USING TECHSTREAM (OPERATE VSV FOR ACIS)
A067588E05
  1. Disconnect the vacuum hose.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch ON and turn the Techstream ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Active the VSV for Intake Control. Operate the VSV for ACIS.

  1. Check the VSV operation when it is operated using the Techstream.

    Standard:
    Tester Operation
    Specified Condition
    VSV ON
    Air from port E flows out through port F
    VSV OFF
    Air from port E flows out through air filter

    Result:
    Result
    Proceed to
    NG
    A
    OK
    B

  1. Reconnect the vacuum hose.



B
Go to step 4
A


2.CHECK VSV FOR ACIS (OPERATION)
  1. Inspect VSV for ACIS (Click here).



NG
REPLACE VSV FOR ACIS
OK


3.CHECK HARNESS AND CONNECTOR (VSV FOR ACIS - ECM, VSV FOR ACIS - EFI NO. 2 FUSE)
A162272E01
  1. Check the wire harness and connectors between the VSV for ACIS and ECM.

    1. Disconnect the D61 VSV for ACIS connector.

    2. Disconnect the D74 ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance (Check for open):
      Tester Connection
      Condition
      Specified Condition
      D61-2 - D74-62 (ACIS)
      Always
      Below 1 Ω

      Standard resistance (Check for short):
      Tester Connection
      Condition
      Specified Condition
      D61-2 or D74-62 (ACIS) - Body ground
      Always
      10 kΩ or higher

    4. Reconnect the VSV for ACIS connector.

    5. Reconnect the ECM connector.

  1. Check the wire harness between the VSV for ACIS and EFI NO. 2 fuse.

    1. Disconnect the D61 VSV for ACIS connector.

    2. Remove the EFI NO. 2 fuse from the engine room relay block.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance (Check for open):
      Tester Connection
      Condition
      Specified Condition
      D61-1 - EFI NO. 2 fuse (2)
      Always
      Below 1 Ω

    4. Reconnect the VSV for ACIS connector.

    5. Reinstall the EFI relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK VACUUM HOSES (INTAKE MANIFOLD - IACV, IACV - VSV FOR ACIS)
  1. Check that the vacuum hose is connected correctly.

  1. Check the vacuum hose for looseness and disconnection.

  1. Check the vacuum hose for cracks, holes and damage.



NG
REPAIR OR REPLACE VACUUM HOSES
OK


5.INSPECT INTAKE AIR SURGE TANK (INTAKE AIR CONTROL VALVE)


    A075984E02
  1. Check that the lever moves when a vacuum of 26.6 kPa (200 mmHg, 7.85 in.Hg) is applied with the vacuum gauge on.

    OK:
    Lever moves

  1. Check that the vacuum of 26.6 kPa (200 mmHg, 7.85 in.Hg) is sustained for 1 minute in the above state.

    OK:
    Vacuum is sustained



NG
REPLACE INTAKE AIR SURGE TANK (INTAKE AIR CONTROL VALVE) (Click here)
OK

REPLACE ECM (Click here)