Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B1810/53    Short in Driver Side Squib 2nd Step Circuit

DTC    B1811/53    Open in Driver Side Squib 2nd Step Circuit

DTC    B1812/53    Short to GND in Driver Side Squib 2nd Step Circuit

DTC    B1813/53    Short to B+ in Driver Side Squib 2nd Step Circuit

for Preparation Click here


DESCRIPTION

The driver side squib 2nd step circuit consists of the center airbag sensor, the spiral cable and the steering pad.
The circuit instructs the SRS to deploy when the deployment conditions are met.
These DTCs are recorded when a malfunction is detected in the driver side squib 2nd step circuit.

DTC Code
Detection Condition
Trouble Area
B1810/53
When all conditions below are met:
  1. The center airbag sensor receives a line short circuit signal 5 times in the driver side squib 2nd step circuit during primary check.
  2. Driver side squib 2nd step malfunction
  3. Spiral cable malfunction
  4. Center airbag sensor malfunction
  1. Instrument panel wire
  2. Spiral cable
  3. Steering pad (Driver side squib 2nd step)
  4. Center airbag sensor assembly
B1811/53
When all conditions below are met:
  1. The center airbag sensor receives an open circuit signal in the driver side squib 2nd step circuit for 2 seconds.
  2. Driver side squib 2nd step malfunction
  3. Spiral cable malfunction
  4. Center airbag sensor malfunction
  1. Instrument panel wire
  2. Spiral cable
  3. Steering pad (Driver side squib 2nd step)
  4. Center airbag sensor assembly
B1812/53
When all conditions below are met:
  1. The center airbag sensor receives a short circuit to ground signal in the driver side 2nd step circuit for 0.5 seconds.
  2. Driver side squib 2nd step malfunction
  3. Spiral cable malfunction
  4. Center airbag sensor malfunction
  1. Instrument panel wire
  2. Spiral cable
  3. Steering pad (Driver side squib 2nd step)
  4. Center airbag sensor assembly
B1813/53
When all conditions below are met:
  1. The center airbag sensor receives a short circuit to B+ signal in the driver side squib 2nd step circuit for 0.5 seconds.
  2. Driver side squib 2nd step malfunction
  3. Spiral cable malfunction
  4. Center airbag sensor malfunction
  1. Instrument panel wire
  2. Spiral cable
  3. Steering pad (Driver side squib 2nd step)
  4. Center airbag sensor assembly

WIRING DIAGRAM


C146254E74


INSPECTION PROCEDURE

NOTICE:
  1. When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (Click here).
  2. After the ignition switch is turned OFF, the navigation system requires approximately 90 seconds to record various types of memory and settings. As a result, after turning the ignition switch OFF, wait 90 seconds or more before disconnecting the cable from the negative (-) battery terminal.

HINT:
  1. Perform the simulation method by selecting "check mode" (signal check) with the Techstream (Click here).
  2. After selecting "check mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on various types of roads (Click here).

1.CHECK STEERING PAD (DRIVER SIDE SQUIB 2ND STEP)
C158844E02
  1. Turn the ignition switch OFF.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the z5 connector from the steering pad.

  1. Connect the white wire side of SST (resistance: 2.1 Ω) to connector E (black connector).

    CAUTION:
    Never connect the tester to the steering pad (driver side squib 2nd step) for measurement, as this may lead to a serious injury due to airbag deployment.

    NOTICE:
    1. Do not forcibly insert SST into the terminals of the connector when connecting SST.
    2. Insert SST straight into the terminals of the connector.

SST
09843-18061  
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch OFF.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1810, B1811, B1812 or B1813 is not output.

    HINT:
    Codes other than DTC B1810, B1811, B1812, B1813 maybe output at this time, but they are not related to this check.



NG
Go to step 2
OK

REPLACE STEERING PAD (Click here)  

2.CHECK CONNECTOR
  1. Turn the ignition switch OFF.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect SST from connector E.

  1. Check that the spiral cable connectors (on the steering pad side) are not damaged.

    OK:
    The lock button is not disengaged, or the claw of the lock is not deformed or damaged.



NG
REPLACE SPIRAL CABLE (Click here)
OK


3.CHECK DRIVER SIDE SQUIB 2ND STEP CIRCUIT
C158845E07
  1. Disconnect the connectors from the center airbag sensor.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    z5-1 (D2-) - Body ground
    Ignition switch ON
    Below 1 V
    z5-2 (D2+) - Body ground

  1. Turn the ignition switch OFF.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    z5-1 (D2-) - z5-2 (D2+)
    Always
    Below 1 Ω

  1. Release the activation prevention mechanism built into connector B (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    z5-1 (D2-) - z5-2 (D2+)
    Always
    1 MΩ or higher
    z5-1 (D2-) - Body ground
    z5-2 (D2+) - Body ground



NG
Go to step 5
OK


4.CHECK CENTER AIRBAG SENSOR
C158846E03
  1. Connect the connectors to the steering pad and the center airbag sensor.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch OFF.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B1810, B1811, B1812 or B1813 is output (for Column Shift Type)
    A
    DTC B1810, B1811, B1812 or B1813 is output (for Floor Shift Type)
    B
    DTC B1810, B1811, B1812 or B1813 is not output
    C

    HINT:
    Codes other than DTC B1810, B1811, B1812, B1813 maybe output at this time, but they are not related to this check.



A
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

B
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
C

USE SIMULATION METHOD TO CHECK (Click here)  

5.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - SPIRAL CABLE)
C158847E06
  1. Restore the released activation prevention mechanism of connector B to the original condition.

  1. Disconnect the instrument panel wire connector from the spiral cable.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    J11-3 - Body ground
    Ignition switch ON
    Below 1 V
    J11-4 - Body ground

  1. Turn the ignition switch OFF.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    J11-3 - J11-4
    Always
    Below 1 Ω

  1. Release the activation prevention mechanism built into connector B (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    J11-3 - J11-4
    Always
    1 MΩ or higher
    J11-3 - Body ground
    J11-4 - Body ground



NG
REPLACE INSTRUMENT PANEL WIRE ASSEMBLY
OK

REPLACE SPIRAL CABLE (Click here)