Home › ENGINE ยท 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P011B    Engine Coolant Temperature / Intake Air Temperature Correlation

for Preparation Click here


DESCRIPTION

The engine has two temperature sensors, an Engine Coolant Temperature (ECT) sensor and an Intake Air Temperature (IAT) sensor, to detect the temperature while the engine is in operation. A thermistor, whose resistance value varies according to the temperature, is built into each sensor. When the temperature is low, the resistance of the thermistor increases. When the temperature is high, the resistance drops. These variations in resistance are transmitted to the ECM as voltage changes. Based on these temperature signals output from the sensors, the ECM determines the fuel injection time and the ignition timing to control the engine.

DTC Code
DTC Detection Condition
Trouble Area
P011B
  1. All of following conditions met:
    (2 trip detection logic)
    1. Battery voltage 10.5 V or more
    2. 7 hours or more elapsed from engine stops on previous trip
    3. 736 seconds after cold engine starts
    4. Minimum Intake Air Temperature (IAT) after engine starts more than -10°C (14°F)
    5. Average Engine Coolant Temperature (ECT) before engine starts more than -10°C (14°F)
    6. Difference between readings of ECT and IAT greater than 20°C (36°F)
  1. Intake air temperature (IAT) sensor
  2. Engine coolant temperature (ECT) sensor
  3. ECM

A163149E04

HINT:
  1. Waiting is required to prevent the temperature of the engine from affecting the readings. If the engine has been operated recently, it will not be possible to accurately compare the readings.
  1. For diagnosis, in order to duplicate the detection conditions of the DTC, it is necessary to park the vehicle for 7 hours. Parking the vehicle for 7 hours ensures that the actual temperature of the ECT and IAT are very similar. When the vehicle has been parked for less than 7 hours, differences in the readings may exist, and this does not necessarily indicate a fault.


MONITOR DESCRIPTION

The ECM monitors the difference between the Engine Coolant Temperature (ECT) and the Intake Air Temperature (IAT) when the engine is started cold to detect the engine temperature conditions accurately. The monitor runs when the engine is started cold after 7 hours or more have elapsed since the engine was stopped (ignition switch turned to OFF) on the previous trip. If the difference between the ECT and the IAT on a cold start exceeds 20°C (36°F), the ECM interprets this as a malfunction in the ECT sensor circuit and IAT sensor circuit, and sets the DTC.

MONITOR STRATEGY


Related DTCs
P011B: Engine Coolant Temperature (ECT)/Intake Air Temperature (IAT) sensor correlation
Required Sensors/Components (Main)
ECT/IAT sensor
Required Sensors/Components (Related)
-
Frequency of Operation
Once per driving cycle
Duration
7 hours or more
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever these DTCs are not present
P2610 (ECM internal engine off timer)
All of following conditions met
Conditions 1 and 2
1. All of following conditions met
Conditions (a), (b), (c) and (d)
(a) After ignition switch ON and engine not running time
Less than 20 seconds
(b) Soak Time
7 hours or more
(c) Battery voltage
10.5 V or more
(d) Time after engine start
736 seconds or more
2. Either of the following conditions are met
Condition (a) and (b)
(a) Minimum IAT after engine start
-10°C (14°F) or more
(b) ECT before engine start
-10°C (14°F) or more

TYPICAL MALFUNCTION THRESHOLDS


Deviated ECT and IAT
Less than -20°C (-36°F) or more than 20°C (36°F)

INSPECTION PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO P011B)
  1. Connect a Techstream to the DLC3.

  1. Turn the ignition switch ON.

  1. Turn the tester ON.

  1. Enter the following menu: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.

    Result:
    Result
    Proceed to
    P011B
    A
    P011B and other DTCs
    B

    HINT:
    If any DTCs other than P011B are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.READ VALUE USING TECHSTREAM (INTAKE AIR TEMPERATURE)
  1. Leave the vehicle for 7 hours or more.

    HINT:
    It is necessary leave the vehicle for 7 hours or more to allow conditions similar to the DTC detection conditions.

  1. Connect a Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester ON.

  1. Enter the following menu: Powertrain / Engine and ECT / All Data / Intake Air.

  1. Read the value displayed on the Techstream.

    OK:
    Difference between the intake air temperature and the actual outside air temperature is within 10°C (18°F).

    HINT:
    Temperature readings on the vehicle's outside temperature gauge (if equipped) are not suitable for comparing to the IAT reading. The outside temperature gauge has a significant delay built in to prevent temperature swings from being displayed on its display. Use an accurate thermometer to determine the outside air temperature.



NG
REPLACE MASS AIR FLOW METER (Click here)
OK


3.READ VALUE USING TECHSTREAM (COOLANT TEMPERATURE)
  1. Connect a Techstream to the DLC3.

  1. Turn the ignition switch ON.

  1. Turn the tester ON.

  1. Enter the following menu: Powertrain / Engine and ECT / All Data / Coolant Temp.

  1. Read the value displayed on the Techstream.

    OK:
    The difference between the coolant temperature and the actual outside air temperature is within 10°C (18°F).

    HINT:
    If the result is not as specified, check if there are heat sources such as a block heater in the engine compartment.



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)
OK

REPLACE ECM (Click here)