AUDIO AND VISUAL SYSTEM (for CrewMax) > Illumination Circuit |

| 1.CHECK ILLUMINATION |
Check if the illumination for the radio receiver, steering pad switch, glove box or other parts (hazard switch, transmission control switch, etc.) come on when the light control switch is turned to the HEAD or TAIL position.
| Result | Proceed to |
| Illumination comes on for all components except steering pad switch.* | A |
| Illumination comes on for all components except radio receiver. | B |
| No illumination comes on (radio receiver, hazard switch, glove box, etc.). | C |
| Illumination comes on for all components except steering pad switch* and radio receiver. | D |
|
| ||||
|
| ||||
|
| ||||
| A | |
| 2.CHECK HARNESS AND CONNECTOR (BATTERY - SPIRAL CABLE) |
![]() |
Disconnect the J45 cable connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| J45-12 (IL+2) - Body ground | Light control switch TAIL or HEAD | 11 to 14 V |
|
| ||||
| OK | |
| 3.INSPECT STEERING PAD SWITCH ASSEMBLY |

Disconnect the z3 switch connector.
Connect the positive (+) lead to terminal IL+2 and the negative (-) lead to terminal EAU of the steering pad switch assembly connector.
Check if the illumination for the steering pad switch assembly comes on.
|
| ||||
| OK | |
| 4.INSPECT SPIRAL CABLE |
![]() |
Disconnect the z3 switch connector.
Disconnect the J45 cable connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| z3-8 (EAU) - J45-4 (EAU) | Spiral cable is turned 2.5 rotations counterclockwise | Below 1 Ω |
| Spiral cable is centered | ||
| Spiral cable is turned 2.5 rotations clockwise | ||
| z3-5 (IL+2) - J45-12 (IL+2) | Spiral cable is turned 2.5 rotations counterclockwise | |
| Spiral cable is centered | ||
| Spiral cable is turned 2.5 rotations clockwise |
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - RADIO RECEIVER) |
![]() |
Disconnect the K3 receiver connector.
Disconnect the J45 cable connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| K3-6 (SWG) - J45-4 (EAU) | Always | Below 1 Ω |
| K3-6 (SWG) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 6.CHECK HARNESS AND CONNECTOR (BATTERY - RADIO RECEIVER) |
![]() |
Disconnect the K1*1 or K4*2 receiver connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| K4-2 (ILL+) - Body ground | Light control switch TAIL or HEAD | 11 to 14 V |
| Tester Connection | Switch Condition | Specified Condition |
| K1-10 (ILL+) - Body ground | Light control switch TAIL or HEAD | 11 to 14 V |
|
| ||||
| OK | ||
| ||
| 7.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - COMBINATION METER) |
![]() |
Disconnect the K2*1 or K4*2 receiver connector.
Disconnect the J28 meter connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| K4-12 (ILL-) - J28-37 (ILL-) | Always | Below 1 Ω |
| K4-12 (ILL-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| K2-5 (ILL-) - J28-37 (ILL-) | Always | Below 1 Ω |
| K2-5 (ILL-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||