DIFFERENTIAL CARRIER ASSEMBLY (for 1GR-FE, 2UZ-FE) > INSTALLATION |
| 1. INSTALL REAR DIFFERENTIAL CARRIER ASSEMBLY |
![]() |
Clean the contact surfaces of the rear differential carrier and the rear axle housing.
Install a new rear differential carrier gasket and the differential carrier with the 10 washers and 10 nuts.
| 2. INSTALL REAR AXLE SHAFT LH |
Install the rear axle shaft LH (Click here).
| 3. INSTALL REAR AXLE SHAFT RH |
| 4. INSTALL PROPELLER SHAFT ASSEMBLY |
Install the propeller shaft for 2WD (Click here).
Install the propeller shaft for 4WD (Click here).
| 5. ADD DIFFERENTIAL OIL |
![]() |
Add differential oil so that the oil level is between 0 to 5 mm (0 to 0.197 in.) from the bottom lip of the differential filler plug hole.
| Item | Oil type and viscosity |
| Front differential | Toyota Genuine Differential gear oil LT 75W-85 GL-5 or equivalent. |
| Rear differential |
| Specified Condition | |
| 2.05 to 2.15 liters (2.2 to 2.3 US qts., 1.8 to 1.9 Imp. qts.) |
| Engine type | Wheelbase type | Cab type | Drive type | Specified Condition |
| 3UR-FE. 3UR-FBE | 3220 mm (10 ft. 6.8 in.) | Regular | 2WD | 3.40 to 3.50 liters (3.6 to 3.7 US qts., 3.0 to 3.1 Imp. qts.) |
| 4WD | ||||
| 3700 mm (12 ft. 1.7 in.) | Regular | 2WD | 3.55 to 3.65 liters (3.8 to 3.9 US qts., 3.1 to 3.2 Imp. qts.) | |
| 4WD | ||||
| Double | 2WD | |||
| 4WD | ||||
| CrewMax | 2WD | 3.70 to 3.80 liters (3.9 to 4.0 US qts., 3.2 to 3.3 Imp. qts.) | ||
| 4WD | 3.55 to 3.65 liters (3.8 to 3.9 US qts., 3.1 to 3.2 Imp. qts.) | |||
| 4180 mm (13 ft. 8.6 in.) | Double | 2WD | 3.70 to 3.80 liters (3.9 to 4.0 US qts., 3.2 to 3.3 Imp. qts.) | |
| 4WD | ||||
| 1GR-FE and 2UZ-FE | 3220 mm (10 ft. 6.8 in.) | Regular | 2WD | 4.00 to 4.10 liters (4.2 to 4.3 US qts., 3.5 to 3.6 Imp. qts.) |
| 4WD | ||||
| 3700 mm (12 ft. 1.7 in.) | ALL | 2WD | 4.55 to 4.65 liters (4.8 to 4.9 US qts., 4.0 to 4.1 Imp. qts.) | |
| 4WD | ||||
| 4180 mm (13 ft. 8.6 in.) | 2WD | |||
| 4WD |
for Rear Differential:
Install a new gasket and the filler plug.
for Front Differential:
Using a 10 mm hexagon wrench, install a new gasket and the filler plug.
| 6. INSTALL REAR WHEEL |
Install the rear wheels.