AUTOMATIC TRANSMISSION ASSEMBLY (for 1GR-FE) > INSTALLATION |
| 1. INSTALL TORQUE CONVERTER ASSEMBLY |
![]() |
Using a vernier caliper and straightedge, measure dimension A between the transmission and the end surface of the drive plate.
Install the torque converter to the transmission housing.
![]() |
Using a vernier caliper and straightedge, measure dimension B shown in the illustration and check that B is greater than A measured in the first step.
| 2. INSTALL TRANSMISSION CONTROL CABLE BRACKET |
![]() |
Install the bracket with the 2 bolts.
| 3. INSTALL WIRE HARNESS CLAMP BRACKET |
Install the front left bank bracket with the bolt.
Install the rear left bank bracket with the bolt.
| 4. INSTALL TRANSMISSION OIL COOLER ASSEMBLY |
![]() |
Coat 2 new O-rings with ATF, and install them to the transmission oil cooler.
Align the transmission oil cooler with the transmission oil cooler spacer and assemble them with the 3 bolts.
Connect the 2 hoses to the transmission oil cooler spacer with the 2 clips.
![]() |
Install the transmission oil cooler with transmission oil cooler spacer with the 3 bolts.
Connect the 2 hoses with the 2 clips.
| 5. INSTALL AUTOMATIC TRANSMISSION ASSEMBLY |
![]() |
Install the transmission with the 9 bolts.
| 6. CONNECT NO. 1 WATER BY-PASS PIPE |
![]() |
Connect the 2 water by-pass hoses with the 2 clips and install the water by-pass pipe with the 2 bolts.
| 7. CONNECT WIRE HARNESS AND CONNECTOR |
![]() |
Connect the park/neutral start switch connector, transmission wire connector and 2 speed sensor connectors.
Connect the harness clamp with the bolt.
Connect the 4 connector clamps and 4 harness clamps.
Tilt up the automatic transmission.
![]() |
Connect the ground cable with the bolt.
| 8. INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR |
![]() |
Install the rear engine mounting insulator to the transmission with the 4 bolts.
| 9. INSTALL NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY |
![]() |
Install the frame crossmember to the rear engine mounting insulator with the 4 bolts.
![]() |
Install the frame crossmember with the 4 bolts, 4 washers and 4 nuts.
| 10. INSTALL DRIVE PLATE AND TORQUE CONVERTER CLUTCH SETTING BOLT |
![]() |
Turn the crankshaft to gain access to the 6 bolts and install each bolt while holding the crankshaft pulley setting bolt with a wrench.
![]() |
Install the flywheel housing side cover.
| 11. INSTALL STARTER ASSEMBLY (for 2.0 kW Type) |
![]() |
Install the starter with the 2 bolts.
Connect the starter connector.
Connect the starter wire with the nut.
Install the terminal cap.
| 12. INSTALL STARTER ASSEMBLY (for 1.6 kW Type) |
![]() |
Install the starter with the 2 bolts.
Connect the starter connector.
Connect the starter wire with the nut.
Install the terminal cap.
| 13. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY |
![]() |
Connect the control cable with a new clip and nut.
| 14. INSTALL FRONT EXHAUST PIPE ASSEMBLY |
for Regular Cab Standard Deck:
Install the front exhaust pipe (Click here).
except Regular Cab Standard Deck:
Install the front exhaust pipe (Click here).
| 15. INSTALL PROPELLER SHAFT ASSEMBLY |
Install the propeller shaft (Click here).
| 16. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 17. ADD AUTOMATIC TRANSMISSION FLUID |
Add automatic transmission fluid (Click here).
| 18. ADD ENGINE COOLANT |
Add engine coolant.
![]() |
Slowly pour coolant into the radiator reservoir until it reaches the FULL line.
Install the reservoir cap.
Press the inlet and outlet radiator hoses several times by hand, and then check the coolant level. If the coolant level is low, add coolant.
Install the radiator cap.
Start the engine and warm it up until the thermostat opens.
Maintain the engine speed at 2000 to 2500 rpm.
Press the inlet and outlet radiator hoses several times by hand to bleed air.
Stop the engine, and wait until the engine coolant cools down to ambient temperature.
![]() |
Check that the coolant level is between the FULL and LOW lines.
If the coolant level is below the LOW line, repeat all of the procedures above.
If the coolant level is above the FULL line, drain coolant so that the coolant level is between the FULL and LOW lines.
| 19. CHECK FOR ENGINE COOLANT LEAK |
![]() |
Fill the radiator with coolant and attach a radiator cap tester.
Warm up the engine.
Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and head.
| 20. ADJUST SHIFT LEVER POSITION (for Column Shift Type) |
Move the shift lever to the N position.
![]() |
Fold back the transmission control cable adjust case cover. Then while sliding the slider toward the cable end side, press the lock piece from the back side to release the lock.
![]() |
Check that the adjust case's spring is applying enough tension to the shift control cable. Then press the lock piece to set the lock.
Return the cover of the adjust case to its original position.
Inspect the operation after the adjustment.
| 21. ADJUST SHIFT LEVER POSITION (for Floor Shift Type) |
Move the shift lever to the N position.
![]() |
Fold back the transmission control cable adjust case cover. Then while sliding the slider toward the cable end side, press the lock piece from the back side to release the lock.
![]() |
Check that the adjust case's spring is applying enough tension to the shift control cable. Then press the lock piece to set the lock.
Return the cover of the adjust case to its original position.
Inspect the operation after the adjustment.
| 22. INSPECT SHIFT LEVER POSITION (for Column Shift Type) |
When moving the shift lever from the N position to other positions, check that the lever can be shifted smoothly and accurately to each position and that the position indicator comes on in accordance with the shift lever position.
If the indicator and shift lever position do not match, carry out the following adjustment procedures.
| 23. INSPECT SHIFT LEVER POSITION (for Floor Shift Type) |
When moving the shift lever from the N position to other positions, check that the lever can be shifted smoothly and accurately to each position and that the position indicator comes on in accordance with the shift lever position.
If the indicator and shift lever position do not match, carry out the following adjustment procedures.
| 24. CHECK FOR EXHAUST GAS LEAK |
| 25. INSTALL NO. 1 ENGINE UNDER COVER |
| 26. PERFORM RESET MEMORY |
Perform the RESET MEMORY procedures (A/T initialization) (Click here).