Home › ENGINE ยท 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P050A    Cold Start Idle Air Control System Performance

for Preparation Click here


DESCRIPTION

This monitor will run when the engine is started at an engine coolant temperature of -10 to 50°C (14 to 122°F). The DTC will set after the engine idles for 13 seconds (2 trip detection logic).
The DTC is designed to monitor the idle air control at cold start. When the engine is started at an engine coolant temperature of lower than 50°C (122°F), the ECM measures the accumulated mass air flow at engine idling. If it does not reach the specified level within 10 seconds, the ECM interprets this as a malfunction. The MIL is illuminated and a DTC is set when the malfunction is detected in consecutive driving cycles (2 trip detection logic).
The ETCS (Electronic Throttle Control System) controls the idle speed. The ETCS operates the throttle actuator to open and close the throttle valve, and adjusts the intake air amount to achieve the target idle speed.

NOTICE:
When the negative battery terminal is disconnected during inspections or repairs, the ISC (Idle Speed Control) learning values are cleared. This DTC cannot be set with the ISC learning values cleared.

HINT:
The ISC learning is performed when the engine is warmed up and has been idling for 5 minutes.


A153341E02


DTC Code
DTC Detection Condition
Trouble Area
P050A
Insufficient mass air flow at cold start (2-trip detection logic)
  1. Throttle body assembly
  2. Mass air flow meter
  3. PCV system
  4. Air cleaner filter element
  5. Air induction system
  6. VVT system
  7. ECM

MONITOR STRATEGY


Related DTCs
P050A: Cold start idle air speed control system
Required Sensors / Components (Main)
Throttle body assembly
Required Sensors / Components (Related)
Mass air flow meter
Engine Coolant Temperature (ECT) sensor
Frequency of Operation
Once per driving cycle
Duration
10 seconds
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not present
P0010, P0020 (VVT Oil Control Valve)
P0011, P0021 (VVT System - Advance)
P0012, P0022 (VVT System - Retard)
P0016, P0018 (VVT System - Misalignment)
P2195, P2196, P2197, P2198, P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255, P2256, P2A00, P2A03 (Air Fuel Ratio Sensor)
P0102, P0103 (Mass Air Flow Meter)
P0115, P0117, P0118 (Engine Coolant Temperature Sensor)
P0125 (Insufficient Coolant Temperature for Closed Loop Fuel Control)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle Position Sensor)
P0171, P0172, P0174, P0175 (Fuel System)
P0301 - P0306 (Misfire)
P0340, P0342, P0343, P0345, P0347, P0348 (VVT Sensor)
P0351 - P0356 (Igniter)
P0500 (Vehicle Speed Sensor)
P0705 (Shift Lever Position Switch)
Battery voltage
8 V or more
Time after engine start
3 seconds or more
Starter
OFF
ECT at engine start
-10°C (14°F) or more
ECT
-10 to 50°C (14 to 122°F)
Engine idling time
3 seconds or more
Fuel-cut
OFF
Vehicle speed
Less than 1.875 mph (3 km/h)
Time after shift position changed
1 second or more
Atmospheric pressure
76 kPa (570 mmHg) or more

TYPICAL MALFUNCTION THRESHOLDS


Accumulated mass air flow
Varies with ECT (Example: Less than 10 g)

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P050A)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch ON.

  1. Turn the Techstream ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result:

    Display (DTC Output)
    Proceed to
    P050A
    A
    P050A and other DTCs
    B

    HINT:
    If any DTCs other than P050A are output, troubleshoot those DTCs first.



NG
GO TO DTC CHART (Click here)
OK


2.READ VALUE USING TECHSTREAM (FUEL TRIM)

HINT:
Calculate the total fuel trim values to check the characteristic deviation of the mass air flow meter.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch ON.

  1. Turn the Techstream ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / A/F Control System / Short FT #1 and Long FT #1, or Short FT #2 and Long FT #2.

  1. Read the values displayed on the Techstream.

  1. Add together the Short FT #1 and Long FT #1, or Short FT #2) and Long FT #2 values to obtain the total Fuel Trim

    OK:
    Total of Short FT #1 and Long FT #1, or Short FT #2 and Long FT #2 values is between -20% and 20%.



NG
Go to step 5
OK


3.CHECK THROTTLE BODY
  1. Check that there are no deposits around the throttle valve.

    OK:
    No deposits around the throttle valve



NG
Go to step 10
OK


4.REPLACE ECM
  1. Replace ECM (Click here).



NEXT
Go to step 15

5.PERFORM ACTIVE TEST USING TECHSTREAM (OPERATE OCV)
  1. Connect the Techstream to the DLC3.

  1. Start the engine and turn the Techstream ON.

  1. Warm up the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT System (Bank 1) or Control the VVT System (Bank 2).

  1. Check the engine speed while operating the Oil Control Valve (OCV) using the Techstream.

    OK:

    Tester Operation
    Specified Condition
    OCV OFF
    Normal engine speed
    OCV ON
    Engine idles roughly or stalls (soon after OCV switched from OFF to ON)



NG
Go to step 11
OK


6.CHECK PCV SYSTEM
  1. Start the engine.

  1. Pinch the positive crankcase PCV hose.

  1. Check the engine rpm.

    OK:
    The engine rpm rises when the PCV hose is pinched.



NG
Go to step 12
OK


7.CHECK AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
  1. Visually check that the air cleaner filter element is not excessively contaminated with dirt or oil.

    OK:
    The air cleaner filter element is not excessively contaminated with dirt or oil.



NG
Go to step 13
OK


8.CHECK AIR INDUCTION SYSTEM
  1. Check the air induction system for vacuum leaks.

    OK:
    No leakage from the air induction system.



NG
Go to step 14
OK


9.REPLACE MASS AIR FLOW METER
  1. Replace mass air flow meter (Click here).



NEXT
Go to step 15

10.REPAIR OR REPLACE THROTTLE BODY
  1. Repair or replace throttle body (Click here).



NEXT
Go to step 15

11.CHECK AND REPAIR VVT SYSTEM


NEXT
Go to step 15

12.REPAIR OR REPLACE PCV SYSTEM


NEXT
Go to step 15

13.REPLACE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY


NEXT
Go to step 15

14.REPAIR OR REPLACE AIR INDUCTION SYSTEM


NEXT
Go to step 15

15.CHECK WHETHER DTC OUTPUT RECURS (DTC P050A)

NOTICE:
For this operation, the engine must be cold (the same level as the engine coolant temperature recorded in the freeze frame data).

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch ON.

  1. Turn the Techstream ON.

  1. Clear the DTCs (Click here).

  1. Switch the ECM from normal mode to check mode using the Techstream (Click here).

  1. Start the engine and idle it for 1 minute.

    OK:
    Stable fast idle

  1. Read the DTCs.

    OK:
    No DTC is output.


NEXT

END