Home › ENGINE ยท 2UZ-FE › LUBRICATION › OIL PUMP

OIL PUMP > INSTALLATION

for Preparation Click here



1. INSTALL OIL PUMP ASSEMBLY


    A150127
  1. Apply a light coat of engine oil to a new O-ring and install it to the cylinder block.



    A150126E01
  1. Apply seal packing to the oil pump as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard seal diameter:
    2.0 to 3.0 mm (0.0787 to 0.118 in.)

    NOTICE:
    1. Install the oil pump within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.
    2. Be careful not to drop any oil on the contact surfaces of the oil pump and cylinder block.
    3. Do not expose the seal to engine oil for at least an hour after installing it.



    A150128
  1. Align the oil pump's drive rotor spline and the crankshaft as shown in the illustration. Install the spline and oil pump to the crankshaft.



    A150140E01
  1. Install the oil pump with the 7 standard bolts and 6 mm hexagon wrench bolt. Uniformly tighten the bolts in several steps.

    Torque:
    for bolt A, B, C, E:
    16 N*m{ 163 kgf*cm , 12 ft.*lbf }
    for bolt D:
    31 N*m{ 316 kgf*cm , 23 ft.*lbf }

    Bolt length:
    Item
    Bolt Head Size
    Length
    Bolt A
    12 mm
    35 mm (1.38 in.)
    Bolt B
    12 mm
    50 mm (1.97 in.)
    Bolt C
    14 mm
    103 mm (4.06 in.)
    Bolt D
    14 mm
    44 mm (1.73 in.)
    Bolt E
    6 mm hexagon
    28 mm (1.10 in.)



2. INSTALL OIL STRAINER SUB-ASSEMBLY


    A150116
  1. Install a new gasket and the oil strainer with the 2 bolts and 2 nuts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



3. INSTALL NO. 1 OIL PAN SUB-ASSEMBLY
  1. Remove any old packing (FIPG).

    1. Using a gasket scraper, remove all the old packing (FIPG) from the gasket surfaces and sealing groove. Thoroughly clean all components.

    2. Using a non-residue solvent, clean both sealing surfaces.



    A150129E01
  1. Apply seal packing to the No. 1 oil pan as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard seal diameter:
    3.0 to 5.0 mm (0.118 to 0.197 in.)

    NOTICE:
    1. Install the oil pan within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.
    2. Be careful not to drop any oil on the contact surfaces of the oil pan and cylinder block.
    3. Do not expose the seal to engine oil for at least an hour after installing it.



    A150114E01
  1. Temporarily install the No. 1 oil pan with the 19 bolts, stud bolt and 2 nuts.

    Bolt length:
    Item
    Bolt Head Size
    Length
    Bolt A
    10 mm
    22 mm (0.866 in.)
    Bolt B
    12 mm
    25 mm (0.984 in.)
    Bolt C
    12 mm
    60 mm (2.36 in.)
    Bolt D
    10 mm
    35 mm (1.38 in.)
    Bolt E
    10 mm
    22 mm (0.866 in.)

    NOTICE:
    Make sure the rear ends of the No. 1 oil pan and cylinder block are aligned. If not, the oil pan may become damaged.

  1. Uniformly tighten the bolts and nuts in several passes.

    Torque:
    for bolt A, D, E:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }
    for bolt B, C, nut:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }



4. INSTALL NO. 2 OIL PAN SUB-ASSEMBLY


    A150130E01
  1. Apply seal packing to the No. 2 oil pan as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard seal diameter:
    3.0 to 5.0 mm (0.118 to 0.197 in.)

    NOTICE:
    1. Install the oil pan within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.
    2. Be careful not to drop any oil on the contact surfaces of the No. 1 oil pan and No. 2 oil pan.
    3. Do not expose the seal to engine oil for at least an hour after installing it.



    A150113
  1. Install the No. 2 oil pan with the 8 bolts and 2 nuts. Uniformly tighten the bolts and nuts in several passes.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



5. INSTALL CRANKSHAFT POSITION SENSOR


    A153483
  1. Install the sensor with the bolt.

    Torque:
    6.5 N*m{ 65 kgf*cm , 58 in.*lbf }

  1. Connect the sensor connector.



6. INSTALL OIL FILTER BRACKET SUB-ASSEMBLY


    A163799
  1. Install a new gasket to the oil filter bracket.

  1. Install the oil filter bracket with the 2 bolts and nut.

    Torque:
    18 N*m{ 185 kgf*cm , 13 ft.*lbf }

  1. Connect the oil cooler hoses to the oil cooler.

  1. Connect the oil pressure sender gauge connector.



7. INSTALL OIL FILTER ASSEMBLY


    A150110
  1. Clean and check the oil filter installation surface.

  1. Apply clean engine oil to the gasket of a new oil filter.

  1. Lightly screw the oil filter into place by hand. Tighten it until the gasket contacts the seat.



    A150111E01
  1. Using SST, tighten the oil filter. Depending on the work space available, choose from the following.

    SST
    09228-07501  

    1. If enough space is available, use a torque wrench to tighten the oil filter.

      Torque:
      17 N*m{ 173 kgf*cm , 13 ft.*lbf }

    2. If enough space is not available to use a torque wrench, tighten the oil filter a 3/4 turn by hand or with a common wrench.



8. INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE


    A150112E02
  1. Apply a light coat of engine oil to a new O-ring.

  1. Install a new O-ring to the guide.

  1. Install the dipstick guide with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Install the dipstick.



9. INSTALL CRANKSHAFT TIMING PULLEY


    A004446E02
  1. Align the timing pulley set key with the key groove of the pulley.

  1. Using SST and a hammer, tap in the timing pulley with the flange side facing inward.

    SST
    09223-46011  



10. INSTALL TIMING BELT
  1. Install the timing belt (Click here).



11. INSTALL ENGINE ASSEMBLY
  1. Install the engine to the vehicle (Click here).



12. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
Some systems need to be initialized after the cable is reconnected (Click here).