Home › ENGINE ยท 2UZ-FE › ENGINE MECHANICAL › ENGINE ASSEMBLY

ENGINE ASSEMBLY > INSTALLATION

for Preparation Click here



1. REMOVE ENGINE STAND
  1. Attach an engine sling device and hang the engine with a chain block.

  1. Remove the bolts and engine assembly from the engine stand.



2. INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY RH


    A156199E03
  1. Place a new gasket on the cylinder head with the "R" mark facing the manifold side.

    NOTICE:
    Be careful of the installation direction.



    A156203E02
  1. Temporarily install the exhaust manifold, and then uniformly tighten 8 new nuts in several steps, in the sequence shown in the illustration.

    Torque:
    44 N*m{ 428 kgf*cm , 31 ft.*lbf }



3. INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR
  1. Temporarily install the heat insulator with the 4 bolts.



    A156201E01
  1. Uniformly tighten the 4 bolts in several steps, in the sequence shown in the illustration.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



4. INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE


    A150112E02
  1. Apply a light coat of engine oil to a new O-ring.

  1. Install a new O-ring to the guide.

  1. Install the dipstick guide with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Install the dipstick.



5. INSTALL NO. 2 AIR TUBE


A153512
  1. Temporarily install a new gasket and the No. 2 air tube to the exhaust manifold side with the 2 nuts.

  1. Install a new gasket and the No. 2 air tube to the air switching valve side with the 2 nuts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Tighten the 2 nuts on the exhaust manifold side.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



    A153510
  1. Connect the air pump connector.

  1. Connect the wire harness clamp.



6. INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY LH


    A156200E02
  1. Place a new gasket on the cylinder head with the "L" mark facing the manifold side.

    NOTICE:
    Be careful of the installation direction.



    A156204E03
  1. Temporarily install the exhaust manifold, and then uniformly tighten 8 new nuts in several steps, in the sequence shown in the illustration.

    Torque:
    44 N*m{ 449 kgf*cm , 32 ft.*lbf }



7. INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR
  1. Temporarily install the heat insulator with the 4 bolts.



    A156202E03
  1. Uniformly tighten the 4 bolts in several steps, in the sequence shown in the illustration.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



8. INSTALL NO. 3 AIR TUBE


A153518
  1. Temporarily install a new gasket and the No. 3 air tube to the exhaust manifold side with the 2 nuts.

  1. Install a new gasket and the No. 3 air tube to the air switching valve side with the 2 nuts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Tighten the 2 nuts on the exhaust manifold side.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



9. INSTALL ENGINE ASSEMBLY
  1. Slowly lower the engine assembly into the engine compartment.

    NOTICE:
    Make sure that the engine is clear of all wiring and hoses.

  1. Attach the engine mounting insulators to the vehicle.



    A160773E01
  1. Install the 4 engine mounting insulator's bolts.

    Torque:
    79 N*m{ 806 kgf*cm , 58 ft.*lbf }



10. INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY


    A160799E01
  1. Using SST, hold the crankshaft.

    SST
    09213-70011  
    09330-00021  

  1. Install the front drive plate spacer, drive plate and rear drive plate spacer on the crankshaft.



    A160778E01
  1. Install and uniformly tighten 8 new bolts in the sequence shown in the illustration.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }

    NOTICE:
    1. Do not reuse the flywheel installation bolts.
    2. Do not impact or damage the flywheel installation bolts. Be sure to handle them carefully.



    A149106E01
  1. Mark the upside of each flywheel installation bolt with paint.

  1. Retighten the flywheel installation bolts by 90° as shown.

  1. Check that the painted marks are now at a 90° angle to the upside.



11. INSTALL AUTOMATIC TRANSMISSION ASSEMBLY
  1. for 2WD, refer to the following procedures (Click here).

  1. for 4WD, refer to the following procedures (Click here).



12. INSTALL PROPELLER SHAFT ASSEMBLY
  1. for 2 joint type, refer to the following procedures .

  1. for 3 joint type, refer to the following procedures .



13. INSTALL EXHAUST PIPE ASSEMBLY
  1. for Regular cab standard deck, refer to the following procedures (Click here).

  1. except Regular cab standard deck, refer to the following procedures (Click here).



14. INSTALL NO. 1 WATER BY-PASS PIPE


    A160801
  1. Install the water by-pass pipe with the 2 bolts.



15. INSTALL GENERATOR ASSEMBLY


    A152262E01
  1. Install the generator with the bolt and 2 nuts.

    Torque:
    for bolt and nut (A):
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }
    for nut (B):
    16 N*m{ 163 kgf*cm , 12 ft.*lbf }



    A152261
  1. Connect the generator connector.

  1. Connect the generator wire with the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Install the terminal cap.

  1. Install the harness bracket to the generator with the bolt.

    Torque:
    8.2 N*m{ 84 kgf*cm , 73 in.*lbf }



16. CONNECT VANE PUMP ASSEMBLY
  1. Connect the vane pump with the nut and 2 bolts.

    Torque:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }

  1. Connect the connector.



17. CONNECT COOLER COMPRESSOR ASSEMBLY


    A160758
  1. Connect the compressor. Then install it and the No. 1 compressor stay with the nut and 3 bolts.

    Torque:
    for bolt:
    47 N*m{ 479 kgf*cm , 35 ft.*lbf }
    for nut:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

  1. Connect the connector.



18. CONNECT WIRE HARNESS AND HOSE


    A160786E01
  1. Connect the 3 connectors to the engine room junction block.

  1. Install the engine wire with the nut.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Connect the 4 air injection control driver connectors.

  1. Install the ground wire with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the positive (+) battery terminal and install the engine wire with the nut.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }



    A160785E01
  1. Connect the air injection system hose.

  1. Install the ground wire with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the air pump connector and install the connector bracket with the bolt.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }



    A160782E01
  1. Connect the 4 connectors to the connector holder block.



    A160783E01
  1. Connect the heater hoses.

  1. Connect the ECM connector and clamp.

    HINT:
    Refer to the following procedures to connect the ECM connector .



    A191534E01
  1. Connect the vacuum hose assembly.



19. CONNECT FUEL MAIN AND RETURN HOSE


    A160798
  1. Connect the fuel main and return hoses (Click here).

  1. Install the fuel pipe clamp.



20. INSTALL RADIATOR ASSEMBLY


    A156167
  1. Set the radiator bracket hooks to the radiator support holes.

  1. Install the radiator with the 4 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



21. INSTALL OIL COOLER ASSEMBLY (w/ Trailer Towing System)
  1. Install the oil cooler (Click here).



22. INSTALL FLUID COUPLING ASSEMBLY
  1. Set the fan pulley to the fan bracket.



    A151756
  1. Set the fan together with the fan shroud into the vehicle.

    NOTICE:
    1. Be careful not to damage the radiator core.
    2. Make sure to attach the 2 claws of the fan shroud to the vehicle.

  1. Temporarily install the fan to the fan pulley with the 4 fluid coupling nuts.

  1. Install the fan shroud with the 2 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }



    A123358
  1. Tighten the 4 fluid coupling nuts.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }



23. INSTALL FAN AND GENERATOR V BELT


    A053117E03
  1. Set the V belt onto every part except the No. 2 idler pulley, as shown in the illustration.

  1. Loosen the V belt by turning the belt tensioner counterclockwise.

  1. Set the V belt to the No. 2 idler pulley.



    A141644E02
  1. After installing the belt, check that it fits properly in the ribbed grooves.

  1. Check by hand to confirm that the belt has not slipped out of the grooves on the bottom of the pulley.



    A141645E01
  1. Check that the arrow on the belt tensioner is within area "A".
    If it is outside area "A", replace the fan and generator V belt.

    HINT:
    When a new belt is installed, the arrow should be within area "B". If not, the fan and generator V belt is not installed correctly.



24. INSTALL RADIATOR HOSE OUTLET


25. INSTALL RADIATOR HOSE INLET


26. INSTALL RADIATOR SIDE DEFLECTOR LH


    A151774
  1. Install the deflector with the 6 clips.

  1. Install the wire harness clamp.



27. INSTALL RADIATOR SIDE DEFLECTOR RH


    A151775
  1. Install the deflector with the 6 clips.



28. INSTALL AIR CLEANER ASSEMBLY


    A156197
  1. Install the air cleaner case with the 2 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Install the air cleaner element onto the air cleaner case.



    A156196E01
  1. Install the air cleaner cap.

    1. Fasten the 4 hook clamps.

    2. Connect the MAF meter connector.

    3. Attach the wire harness clamp.



29. INSTALL NO. 2 VENTILATION HOSE


    A156192
  1. Install the No. 2 ventilation hose and vacuum hose.



30. INSTALL AIR CLEANER HOSE ASSEMBLY


    A153488E01
  1. Install the air cleaner hose.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }

    HINT:
    Make sure that the clamp band end is aligned with the limit mark when the hose clamp is tightened, as indicated by A and B in the illustration.

  1. Connect the vacuum hose.

  1. Connect the No. 2 ventilation hose.



31. ADD ENGINE OIL
  1. Install a new gasket and the drain plug.

    Torque:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }

  1. Add new oil.

    Standard engine oil:
    Oil grade
    Oil Viscosity (SAE)
    ILSAC multigrade engine oil
    5W-30
    (5W-30 is the best choice for this vehicle for good fuel economy and good starting in cold weather.)

    Standard oil capacity:
    Item
    Specified Condition
    Drain and refill with oil filter change
    6.2 liters (6.6 US qts, 5.5 Imp. qts)
    Drain and refill without oil filter change
    5.7 liters (6.0 US qts, 5.0 Imp. qts)
    Dry fill
    7.1 liters (7.5 US qts, 6.2 Imp. qts)

  1. Install the oil filler cap.



32. ADD ENGINE COOLANT
  1. Add engine coolant.

    Standard capacity:
    9.7 liters (10.3 US qts, 8.5 Imp. qts)

    HINT:
    1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology is a combination of low phosphates and organic acids).
    2. The thermostat opening timing can be confirmed by pressing the inlet radiator hose by hand, and checking when the engine coolant starts to flow inside the hose.



    A151850E03
  1. Slowly pour coolant into the radiator reservoir until it reaches the FULL line.

  1. Install the reservoir cap.

  1. Press the inlet and outlet radiator hoses several times by hand, and then check the coolant level. If the coolant level is low, add coolant.

  1. Install the radiator cap.

  1. Start the engine and warm it up until the thermostat opens.

    HINT:
    The thermostat opening timing can be confirmed by pressing the inlet radiator hose by hand, and checking when the engine coolant starts to flow inside the hose.

  1. Maintain the engine speed at 2000 to 2500 rpm and warm up the engine until the cooling fan operates.

    NOTICE:
    1. Make sure that the radiator reservoir still has some coolant in it.
    2. Pay attention to the needle of the water temperature meter. Make sure that the needle does not show an abnormally high temperature.
    3. If there is not enough coolant, the engine may burn out or overheat.
    4. Immediately after starting the engine, if the radiator reservoir does not have any coolant, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the coolant is filled to the FULL line.
    5. Run the engine at 2000 rpm until the coolant level has stabilized.

  1. Press the inlet and outlet radiator hoses several times by hand to bleed air.

    CAUTION:
    1. Wear protective gloves.
    2. Be careful as the radiator hoses are hot.
    3. Keep your hands away from the fan.

  1. Stop the engine, and wait until the engine coolant cools down to ambient temperature.

    CAUTION:
    Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.



    A151850E04
  1. Check that the coolant level is between the FULL and LOW lines. If the coolant level is below the LOW line, repeat all of the procedures above. If the coolant level is above the FULL line, drain coolant so that the coolant level is between the FULL and LOW lines.



33. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
Some systems need to be initialized after the cable is reconnected (Click here).



34. INSPECT FOR OIL LEAK
  1. Inspect the engine oil leak .



35. INSPECT FOR COOLANT LEAK

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.



    A162054
  1. Fill the radiator with coolant and attach a radiator cap tester.

  1. Warm up the engine.

  1. Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop. If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and head.



36. INSPECT FOR EXHAUST GAS LEAK
If gas is leaking, tighten the areas necessary to stop the leak. Replace damaged parts as necessary.


37. INSPECT FOR FUEL LEAK
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and Techstream main switch ON.

    NOTICE:
    Do not start the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

  1. Check that there are no fuel leaks after doing maintenance anywhere on the fuel system.



    A133618E01
  1. Check that the pulsation damper screw rises up when the fuel pump operates.
    If the operation is not as specified, check the following parts:

    1. Fusible link
    2. Fuses
    3. Circuit opening relay
    4. Fuel pump
    5. ECM
    6. Wiring connections
    If no malfunctions are found in the aforementioned components, replace the pulsation damper.

  1. Turn the ignition switch OFF.

  1. Disconnect the Techstream from the DLC3.



38. INSPECT SHIFT LEVER POSITION
  1. When moving the shift lever from the N position to other positions, check that the lever can be shifted smoothly and accurately to each position and that the position indicator comes on in accordance with the shift lever position.
    If the indicator and shift lever position do not match, carry out the following adjustment procedures.



39. INSTALL THROTTLE BODY COVER SUB-ASSEMBLY


    A153486
  1. Install the throttle body cover sub-assembly with the 2 nuts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



40. INSTALL COWL TOP OUTER PANEL SUB-ASSEMBLY


  1. Install the outer panel with the 7 bolts.


    A151796

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Connect the 2 washer hoses.



41. INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY
  1. Install the windshield wiper motor (Click here).



42. INSTALL HOOD SUB-ASSEMBLY
  1. Install the hood with the 4 bolts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }



    A160840
  1. Attach the lower part of the 2 food supports to the hood support bolt ball joints.

    NOTICE:
    Install the hood support while supporting the hood by hand.

  1. Attach the hood support clips.

    NOTICE:
    Check that the hood support is engaged in the ball joint and it cannot be pulled out.



43. ADJUST HOOD SUB-ASSEMBLY


    B166027
  1. Adjust the hood's position.

    1. Loosen the hood's 4 hinge bolts.

    2. Move the hood and adjust the clearance between the hood and front fender.

    3. Tighten the hood's 4 hinge bolts after the adjustment.

      Torque:
      13 N*m{ 133 kgf*cm , 10 ft.*lbf }



    4. B166028
    5. Adjust the cushion rubber so that the height of the hood and fender are aligned.

      HINT:
      Raise or lower the hood's front end by turning the cushion rubber.



  1. Adjust the hood lock.



      B166029
    1. Using a screwdriver, remove the hood lock nut cap as shown in the illustration.

      HINT:
      Tape the screwdriver tip before use.



    2. B166030
    3. Loosen the 2 bolts and hood lock nut.

    4. Adjust the hood lock position so that the striker can enter it smoothly.

    5. Tighten the bolts and nut after the adjustment.

      Torque:
      8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    6. Install a new cap.



44. INSTALL NO. 1 ENGINE UNDER COVER


    A150108
  1. Hook the engine under cover onto the vehicle body as shown in the illustration.

  1. Install the 3 screws and 5 bolts.

    Torque:
    for bolt:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }
    for screw:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



45. CHECK IGNITION TIMING
  1. Warm up and stop the engine.

    1. Allow the engine to warm up to a normal operating temperature.

  1. When using the Techstream:

    1. Connect the Techstream to the DLC3.

    2. Start the engine and idle it.

    3. Push the Techstream main switch ON.

    4. Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / IGN Advance.

      HINT:
      Refer to the Techstream operator's manual for further details.

      Standard ignition timing:
      5 to 15° BTDC @ idling (transmission in neutral and A/C switch OFF)

    5. Disconnect the Techstream from the DLC3.



    A123205
  1. When not using the Techstream:

    1. Connect the tester probe of a timing light to the wire of the ignition coil connector for the No. 1 cylinder.

      NOTICE:
      Use a timing light that detects primary signals.



    2. H102392E79
    3. Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

      SST
      09843-18040  

      NOTICE:
      Confirm the terminal numbers before connecting them. Connecting the wrong terminals can damage the engine.



    4. A004459E01
    5. Using the timing light, check the ignition timing.

      Ignition timing:
      5 to 15° BTDC @ idling (transmission in neutral and A/C switch OFF)

    6. Remove SST from the DLC3.

    7. Disconnect the timing light from the engine.



46. CHECK ENGINE IDLE SPEED
  1. Warm up and stop the engine.

    1. Allow the engine to warm up to a normal operating temperature.

  1. When using the Techstream:

    1. Connect the Techstream to the DLC3.

      NOTICE:
      Switch off all accessories and the A/C before connecting the Techstream.

    2. Race the engine at 2500 rpm for approximately 90 seconds.

    3. Push the Techstream main switch ON.

    4. Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Engine Speed.

      Standard idle speed:
      650 to 750 rpm (transmission in neutral and A/C switch OFF)

      HINT:
      Refer to the Techstream operator's manual for further details.

      If the idle speed is not as specified, check the air intake system.

    5. Disconnect the Techstream from the DLC3.



    H102392E88
  1. When not using the Techstream:

    1. Using SST, connect the tachometer probe to terminal 9 (TAC) of the DLC3.

      SST
      09843-18030  

      NOTICE:
      Confirm the terminal numbers before connecting them. Connecting the wrong terminals can damage the engine.

    2. Race the engine at 2500 rpm for approximately 90 seconds.

    3. Check the idle speed.

      Idle speed:
      650 to 750 rpm (transmission in neutral and A/C switch OFF)

      If the idle speed is not as specified, check the air intake system.

    4. Disconnect the tachometer from the DLC3.



47. CHECK CO/HC

HINT:
This check is used only to determine whether or not the idle CO/ HC complies with regulations.

  1. Start the engine.

  1. Keep the engine speed at 2500 rpm for approximately 180 seconds.



    A150141E01
  1. Insert the CO/HC meter testing probe at least 40 cm (1.31 ft.) into the tailpipe during idling.

  1. Immediately check CO/HC concentration at idle and/or 2500 rpm.

    HINT:
    When performing the 2 mode (2500 rpm and idle) test, follow the measurement order prescribed by the applicable local regulations.

  1. If the CO/HC concentration does not comply with regulations, troubleshoot in the order given below.

    1. Check the A/F sensor and heated oxygen sensor operation.

    2. See the table below for possible causes, and then inspect and correct the applicable causes if necessary.

      CO
      HC
      Symptom
      Cause
      Normal
      High
      Rough idle
      1. Faulty ignitions:
        1. Incorrect timing
        2. Plugs (contaminated, shorted or gaps are defective)
      2. Incorrect valve clearance
      3. Leaky intake and exhaust valves
      4. Leaky cylinder
      Low
      High
      Rough idle
      (Fluctuating HC reading)
      1. Vacuum leaks:
        1. PCV hose
        2. Intake manifold
        3. Throttle body
        4. Brake booster line
      2. Lean mixture causing misfire
      High
      High
      Rough idle
      (Black smoke from exhaust)
      1. Restricted air filter
      2. Faulty SFI system:
        1. Faulty pressure regulator
        2. Defective ECT sensor
        3. Faulty ECM
        4. Faulty injectors
        5. Faulty throttle position sensor
        6. Faulty MAF meter



48. CHECK ENGINE OIL LEVEL
  1. Warm up the engine, then stop the engine and wait for 5 minutes.

  1. Check that the engine oil level is between the low level and full level marks on the dipstick.
    If low, check for leakage and add oil up to the full level mark.

    NOTICE:
    Do not fill engine oil above the full level mark.



49. CHECK ENGINE COOLANT LEVEL


A151850E03
  1. Check that the engine coolant level is between the LOW and FULL lines when the engine is cold.
    If the engine coolant is low, check for leaks and add "TOYOTA Super Long Life Coolant" or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite and non-borate coolant with long-life hybrid organic acid technology to the FULL line.

    NOTICE:
    Do not substitute plain water for engine coolant.