Home › BODY ELECTRICAL › AUDIO / VISUAL › AUDIO AND VISUAL SYSTEM (for CrewMax)

AUDIO AND VISUAL SYSTEM (for CrewMax) > Bluetooth Handsfree Module Communication Error

for Preparation Click here


INSPECTION PROCEDURE

1.IDENTIFY COMPONENT SHOWN BY SUB-CODE


  1. Enter the diagnostic mode.


    E146479E01

  1. Press the preset switch "3" to change to "Detailed Information Mode".

  1. Identify the component shown by the sub-code.

HINT:
  1. "190 (radio receiver)" is the component shown by the sub-code in the example shown in the illustration.
  1. For details of the DTC display, refer to "DTC CHECK/CLEAR" (Click here).


NEXT


2.CHECK COMPONENT SHOWN BY SUB-CODE
  1. Select the component shown by sub-code.

    HINT:
    The "Bluetooth" handsfree module is built into the radio receiver. If there is a problem between the "Bluetooth" handsfree module and radio receiver, replace the radio receiver.


    Component table: 
    Component
    Proceed to
    Radio Receiver (190) (for Column Shift Type)
    A
    Radio Receiver (190) (for Floor Shift Type)
    B
    Except Radio Receiver
    C



A
REPLACE RADIO RECEIVER (Click here)

B
REPLACE RADIO RECEIVER (Click here)
C


3.CHECK POWER SOURCE CIRCUIT OF COMPONENT SHOWN BY SUB-CODE
  1. Inspect the power source circuit of the component shown by the sub-code.
    If the power source circuit is operating normally, proceed to the next step.

    Component table: 
    Component
    Proceed to
    Stereo component amplifier (440)
    Stereo component amplifier power source circuit (Click here)
    Television display (1B0)*
    Television display assembly power source circuit (Click here)

    HINT:
    *: w/ Rear Seat Entertainment System


NEXT


4.INSPECT RADIO RECEIVER


    E145834E03
  1. Disconnect the K4 and K22* receiver connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    K4-5 (ATX+) - K4-15 (ATX-)
    Always
    60 to 80 Ω
    K22-9 (TXM+) - K22-10 (TXM-)*
    Always
    60 to 80 Ω

    HINT:
    *: w/ Rear Seat Entertainment System

    Result: 
    Result
    Proceed to
    OK
    A
    NG (for Column Shift Type)
    B
    NG (for Floor Shift Type)
    C



B
REPLACE RADIO RECEIVER (Click here)

C
REPLACE RADIO RECEIVER (Click here)
A


5.CHECK HARNESS AND CONNECTOR ("BLUETOOTH" HANDSFREE MODULE - COMPONENT SHOWN BY SUB-CODE)

E142358E03

HINT:
  1. Start the check from the circuit that is near the component shown by the sub-code first.
  1. For details of the connectors, refer to the "TERMINALS OF ECU" (Click here).

  1. Referring to the AVC-LAN wiring diagram below, check the AVC-LAN circuit between the "Bluetooth" handsfree module and the component shown by the sub-code.

    1. Disconnect all connectors between the "Bluetooth" handsfree module and the component shown by the sub-code.

    2. Check for an open or short in the AVC-LAN circuit between the "Bluetooth" handsfree module and the component shown by the sub-code.

      OK:
      There is no open or short circuit.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.REPLACE COMPONENT SHOWN BY SUB-CODE
  1. Replace the component shown by the sub-code with a normal one and check if the same problem occurs again.

    OK:
    Same problem does not occur.

    Result: 
    Result
    Proceed to
    OK
    A
    NG (for Column Shift Type)
    B
    NG (for Floor Shift Type)
    C



B
REPLACE RADIO RECEIVER (BUILT-IN "BLUETOOTH" HANDSFREE MODULE) (Click here)

C
REPLACE RADIO RECEIVER (BUILT-IN "BLUETOOTH HANDSFREE MODULE") (Click here)
A

END