Home › BODY › INTERIOR › ROOF HEADLINING (for Double Cab)

ROOF HEADLINING (for Double Cab) > REMOVAL

for Preparation Click here



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.

NOTICE:
  1. Some systems need to be initialized after the cable is reconnected (Click here).
  2. After the ignition switch is turned OFF, the navigation system requires approximately 90 seconds to record various types of memory and settings. As a result, after turning the ignition switch OFF, wait 90 seconds or more before disconnecting the cable from the negative (-) battery terminal.



2. REMOVE FRONT SEAT ASSEMBLY (for Manual Seat)
  1. Remove the front seat (Click here).



3. REMOVE FRONT SEAT ASSEMBLY (for Power Seat)
  1. Remove the front seat (Click here).



4. REMOVE FRONT SEAT ASSEMBLY (for Center Seat)
  1. Remove the front seat (Click here).



5. REMOVE REAR SEAT ASSEMBLY (for Double Cab)
  1. Remove the rear seat (Click here).



6. REMOVE FRONT DOOR SCUFF PLATE LH


B165841
  1. Detach the 6 claws and 3 clips, and remove the scuff plate.



7. REMOVE FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedures described for the LH side.



8. REMOVE REAR DOOR SCUFF PLATE LH


B165842
  1. Detach the 6 claws and 2 clips, and remove the scuff plate.



9. REMOVE REAR DOOR SCUFF PLATE RH

HINT:
Use the same procedures described for the LH side.



10. REMOVE COWL SIDE TRIM BOARD LH


B165704
  1. Remove the clip.

  1. Detach the 2 clips and remove the cowl side trim board.



11. REMOVE COWL SIDE TRIM BOARD RH

HINT:
Use the same procedures described for the LH side.



12. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH


13. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH


14. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH


15. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH


16. REMOVE FRONT PILLAR GARNISH LH
  1. Using a screwdriver, detach the 2 claws and remove the 2 assist grip plugs.

    HINT:
    Tape the screwdriver tip before use.

  1. Remove the 2 bolts and assist grip.



  1. Detach the claw and remove the front pillar garnish.


    B165705E05



    B165709E03
  1. Protect the curtain shield airbag.

    1. Thoroughly cover the airbag with a cloth or nylon sheet and fix the ends of the cover with adhesive tape, as shown in the illustration.

      NOTICE:
      Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.



17. REMOVE FRONT PILLAR GARNISH RH

HINT:
Use the same procedures described for the LH side.



18. REMOVE LOWER CENTER PILLAR GARNISH LH


B165827
  1. Detach the 2 claws and remove the cover.



    B165828
  1. Remove the bolt and outer lap belt anchor.



    B165829
  1. Detach the 7 clips and 2 claws, and remove the center pillar garnish.



19. REMOVE LOWER CENTER PILLAR GARNISH RH

HINT:
Use the same procedures described for the LH side.



20. REMOVE CENTER PILLAR GARNISH LH
  1. Using a screwdriver, detach the 2 claws and remove the 2 assist grip plugs.

    HINT:
    Tape the screwdriver tip before use.

  1. Remove the 2 bolts and assist grip.

  1. Remove the 2 screws.

  1. Detach the claw.



  1. Pass the front seat outer belt floor anchor through the center pillar garnish, and remove the center pillar garnish.


    B165825E01



21. REMOVE CENTER PILLAR GARNISH RH

HINT:
Use the same procedures described for the LH side.



22. REMOVE FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH


B165848
  1. Detach the 6 claws of the plate, and slide the plate in the direction of the arrow to remove it.



23. REMOVE FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.



24. REMOVE LOWER QUARTER TRIM PANEL ASSEMBLY LH


B165830
  1. Detach the 2 claws and remove the cover.



    B165831
  1. Remove the bolt and outer lap belt anchor.



    B165832
  1. Detach the 6 clips and remove the quarter trim panel lower.



25. REMOVE LOWER QUARTER TRIM PANEL ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.



26. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY LH


B165711E02
  1. Using a screwdriver, detach the claw and remove the cover.

    HINT:
    Tape the screwdriver tip before use.



    B165833
  1. Remove the 2 bolts.

  1. Detach the 4 clips.

  1. Pass the rear seat outer belt floor anchor through the quarter trim panel, and remove the quarter trim panel.



27. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.



28. REMOVE ROOF CONSOLE BOX ASSEMBLY
  1. for Short Type:
    Remove the roof console box .

  1. for Long Type:
    Remove the roof console box .



29. REMOVE ROOM LIGHT ASSEMBLY (w/ Short Type Roof Console Box)
  1. Using a screwdriver, detach the 4 claws and remove the lens.

    HINT:
    Tape the screwdriver tip before use.

  1. Detach the 4 clips.



  1. Disconnect the connector and then remove the room light.


    B165836E01



30. REMOVE VISOR BRACKET COVER LH


B165714
  1. Using a moulding remover, detach the 4 claws and remove the visor bracket cover.



31. REMOVE VISOR BRACKET COVER RH

HINT:
Use the same procedures described for the LH side.



32. REMOVE VISOR ASSEMBLY LH


B165715
  1. w/o Illumination:
    Remove the visor.

    1. Remove the 3 screws and visor.



    B165840
  1. w/ Illumination:
    Remove the visor.

    1. Remove the 4 screws.

    2. Disconnect the connector and then remove the visor.



33. REMOVE VISOR ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.



34. REMOVE VISOR HOLDER (w/o Illumination)


B165713
  1. Remove the screw and visor holder.

    HINT:
    Use the same procedure to remove the visor holder on the other side.



35. REMOVE ASSIST GRIP SUB-ASSEMBLY


B155751E06
  1. Using a screwdriver, detach the 4 claws and remove the 2 assist grip covers.

    HINT:
    Tape the screwdriver tip before use.

  1. Detach the 2 clips and remove the assist grip.



36. REMOVE ASSIST GRIP PLUG


B165716E05
  1. Insert a screwdriver into the service notch and break off the cap.

  1. Detach the clip and remove the assist grip plug.



37. REMOVE COAT HOOK


B168149E01

HINT:
Use the same procedure to remove the coat hook on the other side.

  1. Using a screwdriver, detach the 2 claws and remove the coat hook cap.

    HINT:
    Tape the screwdriver tip before use.

  1. Detach the clip and remove the coat hook.



38. REMOVE ROOF HEADLINING ASSEMBLY


  1. w/ EC Mirror:



      B166355
    1. Detach the 2 claws and remove the inner rear view mirror cover.



    2. B167283
    3. Disconnect the EC mirror connector.



    B165722
  1. Disconnect the roof wire connector and detach each clamp from the front pillar.



  1. Detach the 4 clips and remove the roof headlining.


    B165846E01

    NOTICE:
    Place the removed headlining in the cabin so that it will not be damaged.



39. REMOVE REAR ROOF DRIP SIDE FINISH MOULDING LH


B163281E01
  1. Put protective tape around the moulding.

  1. Using a heat light, heat the moulding.

    NOTICE:
    Do not heat the moulding and vehicle body excessively.

  1. Using a moulding remover, detach the clip and remove the moulding.

    NOTICE:
    1. Do not remove the clip from the vehicle body.
    2. If the clip is damaged or removed accidentally, replace it.



40. REMOVE REAR ROOF DRIP SIDE FINISH MOULDING RH

HINT:
Use the same procedures described for the LH side.



41. REMOVE BACK WINDOW ASSEMBLY


B166482E01
  1. Apply protective tape to the outer surface of the vehicle body to prevent scratches.



    B166483E01
  1. From the interior, insert a piano wire between the vehicle body and back window as shown in the illustration.

  1. Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.



    B166484E01
  1. Place matchmarks over the window and vehicle body on the locations indicated in the illustration.

    HINT:
    Matchmarks do not need to be placed if the window is not going to be reused.

  1. Cut through the adhesive by pulling the piano wire around the back window.

    NOTICE:
    Leave as much adhesive on the vehicle body as possible when removing the back window.



    B166485
  1. Using suction cups, remove the back window glass.

    NOTICE:
    If the stopper is damaged, the back window glass assembly must be replaced. Be careful when performing the procedure.



42. CLEAN BACK WINDOW ASSEMBLY
  1. Using a scraper, remove the damaged spacers and adhesive sticking to the glass.



    B106929
  1. Clean the outer edge of the back window with a non-residue solvent.

    NOTICE:
    1. Do not touch the back window surface after cleaning it.
    2. Be careful not to damage the window.
    3. Even if using a new back window, clean the back window with a non-residue solvent.



43. CLEAN VEHICLE BODY


B106081E11
  1. Using a scraper, remove the moulding and adhesive from the vehicle body.

  1. Clean and shape the contact surface of the vehicle body.

    1. On the contact surface of the vehicle body, use a knife to cut away excess adhesive as shown in the illustration.

      HINT:
      Leave as much adhesive on the vehicle body as possible.

      NOTICE:
      Be careful not to damage the vehicle body.

    2. Clean the contact surface of the vehicle body with cleaner.

      HINT:
      Even if all the adhesive has been removed, clean the vehicle body.



44. TAKE OUT ROOF HEADLINING ASSEMBLY


B165845
  1. Take out the roof headlining from the cabin as shown in the illustration.

    NOTICE:
    Be careful not to damage the roof headlining when taking it out.