ROOF HEADLINING (for CrewMax) > REMOVAL |
| 1. LOWER BACK WINDOW GLASS |
| 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 3. REMOVE FRONT SEAT ASSEMBLY (for Manual Seat) |
Remove the front seat (Click here).
| 4. REMOVE FRONT SEAT ASSEMBLY (for Power Seat) |
Remove the front seat (Click here).
| 5. REMOVE FRONT SEAT ASSEMBLY (for Center Seat) |
Remove the front seat (Click here).
| 6. REMOVE REAR SEAT ASSEMBLY (for CrewMax LH Side) |
Remove the rear seat (Click here).
| 7. REMOVE REAR SEAT ASSEMBLY (for CrewMax RH Side) |
Remove the rear seat (Click here).
| 8. REMOVE FRONT DOOR SCUFF PLATE LH |
![]() |
Detach the 6 claws and 3 clips, and remove the scuff plate.
| 9. REMOVE FRONT DOOR SCUFF PLATE RH |
| 10. REMOVE REAR DOOR SCUFF PLATE LH |
![]() |
Detach the 8 claws and 2 clips, and remove the scuff plate.
| 11. REMOVE REAR DOOR SCUFF PLATE RH |
| 12. REMOVE COWL SIDE TRIM BOARD LH |
![]() |
Remove the clip.
Detach the 2 clips and remove the cowl side trim board.
| 13. REMOVE COWL SIDE TRIM BOARD RH |
| 14. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH |
| 15. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH |
| 16. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH |
| 17. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH |
| 18. REMOVE FRONT PILLAR GARNISH LH |
Using a screwdriver, detach the 2 claws and remove the 2 assist grip plugs.
Remove the 2 bolts and assist grip.
Detach the claw and remove the front pillar garnish.

![]() |
Protect the curtain shield airbag.
Thoroughly cover the airbag with a cloth or nylon sheet and fix the ends of the cover with adhesive tape, as shown in the illustration.
| 19. REMOVE FRONT PILLAR GARNISH RH |
| 20. REMOVE LOWER CENTER PILLAR GARNISH LH |
![]() |
Detach the 2 claws and remove the cover.
![]() |
Remove the bolt and outer lap belt anchor.
![]() |
Detach the 7 clips and 2 claws, and remove the center pillar garnish.
| 21. REMOVE LOWER CENTER PILLAR GARNISH RH |
| 22. REMOVE CENTER PILLAR GARNISH LH |
Using a screwdriver, detach the 2 claws and remove the 2 assist grip plugs.
Remove the 2 bolts and assist grip.
Remove the 2 screws.
Detach the claw.
Pass the front seat outer belt floor anchor through the center pillar garnish, and remove the center pillar garnish.

| 23. REMOVE CENTER PILLAR GARNISH RH |
| 24. REMOVE FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH |
![]() |
Detach the 6 claws of the plate, and slide the plate in the direction of the arrow to remove it.
| 25. REMOVE FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH |
| 26. REMOVE BACK PANEL TRIM RH |
![]() |
Remove the package holder net hook.
Detach the 8 clips and remove the back panel trim.
| 27. REMOVE BACK PANEL TRIM LH |
Remove the package holder net hook.
Detach the 8 clips and remove the back panel trim.

| 28. REMOVE LOWER QUARTER TRIM PANEL ASSEMBLY LH |
![]() |
Detach the 2 claws and remove the cover.
![]() |
Remove the bolt and outer lap belt anchor.
![]() |
Detach the 4 clips and remove the quarter trim panel.
| 29. REMOVE LOWER QUARTER TRIM PANEL ASSEMBLY RH |
![]() |
Detach the 2 claws and remove the cover.
![]() |
Remove the bolt and outer lap belt anchor.
![]() |
Detach the 3 clips and remove the quarter trim panel.
| 30. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY LH |
![]() |
Using a screwdriver, detach the claw and remove the cover.
![]() |
Remove the 2 bolts.
Detach the 4 clips.
Pass the rear seat outer belt floor anchor through the quarter trim panel, and remove the quarter trim panel.
| 31. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY RH |
| 32. REMOVE REAR SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH |
![]() |
Detach the 4 claws of the plate, and slide the plate in the direction of the arrow to remove it.
| 33. REMOVE REAR SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH |
| 34. REMOVE ROOF CONSOLE BOX ASSEMBLY |
for Short Type:
Remove the roof console box .
for Long Type:
Remove the roof console box .
| 35. REMOVE ROOM LIGHT ASSEMBLY |
w/o Rear Seat Entertainment System:
Remove the room light.
Using a screwdriver, detach the 4 claws and remove the lens.
Detach the 4 clips.
Disconnect the connector and then remove the room light.

![]() |
w/ Rear Seat Entertainment System:
Remove the room light.
Detach the 4 clips.
Disconnect the connectors and then remove the room light.
| 36. REMOVE VISOR BRACKET COVER LH |
![]() |
Using a moulding remover, detach the 4 claws and remove the visor bracket cover.
| 37. REMOVE VISOR BRACKET COVER RH |
| 38. REMOVE VISOR ASSEMBLY LH |
![]() |
w/o Illumination:
Remove the visor.
Remove the 3 screws and visor.
![]() |
w/ Illumination:
Remove the visor.
Remove the 4 screws.
Disconnect the connector and then remove the visor.
| 39. REMOVE VISOR ASSEMBLY RH |
| 40. REMOVE VISOR HOLDER (w/o Illumination) |
![]() |
Remove the screw and visor holder.
| 41. REMOVE ASSIST GRIP SUB-ASSEMBLY |
![]() |
Using a screwdriver, detach the 4 claws and remove the 2 assist grip covers.
Detach the 2 clips and remove the assist grip.
| 42. REMOVE ASSIST GRIP PLUG |
![]() |
Insert a screwdriver into the service notch and break off the cap.
Detach the clip and remove the assist grip plug.
| 43. REMOVE ROOF HEADLINING ASSEMBLY |
w/ EC Mirror:
![]() |
Detach the 2 claws and remove the inner rear view mirror cover.
![]() |
Disconnect the EC mirror connector.
![]() |
Disconnect the roof wire connector and detach each clamp from the front pillar.
w/o Sliding Roof:
Remove the headlining.
Detach the 4 clips and remove the roof headlining.

w/ Sliding Roof:
Remove the headlining.
Detach the 4 clips and 12 fasteners, and remove the roof headlining.

![]() |
Take out the roof headlining from the cabin as shown in the illustration.