Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B1650/32    Occupant Classification System Malfunction

for Preparation Click here


DESCRIPTION

The occupant classification system circuit consists of the center airbag sensor and the occupant classification system.
If the center airbag sensor receives signals from the occupant classification ECU, it determines whether the front passenger airbag, the front seat side airbag RH and front seat outer belt should be operated.
DTC B1650/32 is recorded when a malfunction is detected in the occupant classification system circuit.

DTC Code
Detection Condition
Trouble Area
B1650/32
When all conditions below are met:
  1. Occupant classification system malfunction
  2. The center airbag sensor receives a line short circuit, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the occupant classification system circuit for 2 seconds.
  3. Center airbag sensor malfunction
  1. No. 2 floor wire
  2. Front seat wire RH
  3. Occupant classification system
  4. Center airbag sensor assembly

WIRING DIAGRAM


C158891E01


INSPECTION PROCEDURE

NOTICE:
  1. When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (Click here).
  2. After the ignition switch is turned OFF, the navigation system requires approximately 90 seconds to record various types of memory and settings. As a result, after turning the ignition switch OFF, wait 90 seconds or more before disconnecting the cable from the negative (-) battery terminal.

1.CHECK FOR DTC (OCCUPANT CLASSIFICATION ECU)
  1. Turn the ignition switch ON, and wait for at least 10 seconds.

  1. Check for the DTCs of the occupant classification ECU (Click here).



NG
REPAIR CIRCUITS INDICATED BY OUTPUT DTCS
OK


2.CHECK VEHICLE SYSTEM
  1. Check vehicle system.
    Result 
    Result
    Proceed to
    w/o Power seat
    A
    w/ Power seat
    B



A
Go to step 8
B


3.CHECK FOR DTC (CENTER AIRBAG SENSOR)


    C146235E01
  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch OFF.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1650/32 is not output.

    HINT:
    Codes other than DTC B1650/32 maybe output at this time, but they are not related to this check.



NG
Go to step 4
OK

USE SIMULATION METHOD TO CHECK (Click here)  

4.CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch OFF.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor and the occupant classification ECU.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


5.CHECK CONNECTORS
  1. Disconnect the connectors from the center airbag sensor and the occupant classification ECU.

  1. Check that the connectors (on the center airbag sensor side and occupant classification ECU side) are not damaged.

    OK:
    The connectors are not damaged or damaged.



NG
REPLACE HARNESS AND CONNECTOR
OK


6.CHECK OCCUPANT CLASSIFICATION SYSTEM CIRCUIT

C159566E01

  1. Using a service wire, connect terminal 12 (FSP+) and 13 (FSP-) of connector B.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    Y2-4 (FSR-) - Y2-8 (FSR+)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    Y2-4 (FSR-) - Y2-8 (FSR+)
    Always
    1 MΩ or higher
    Y2-4 (FSR-) - Body ground
    Y2-8 (FSR+) - Body ground

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    Y2-4 (FSR-) - Body ground
    Ignition switch ON
    Below 1 V
    Y2-8 (FSR+) - Body ground

    Result 
    Result
    Proceed to
    OK (for Floor Shift Type)
    A
    OK (for Column Shift Type)
    B
    NG
    C



A
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

B
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
C


7.CHECK NO. 2 FLOOR WIRE

C159567E01

  1. Turn the ignition switch OFF.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the front seat wire RH connector from the No. 2 floor wire.

  1. Using a service wire, connect terminal 12 (FSP+) and 13 (FSP-) of connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    QY1-8 (FSR+) - QY1-9 (FSR-)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    QY1-8 (FSR+) - QY1-9 (FSR-)
    Always
    1 MΩ or higher
    QY1-8 (FSR+) - Body ground
    QY1-9 (FSR-) - Body ground

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    QY1-8 (FSR+) - Body ground
    Ignition switch ON
    Below 1 V
    QY1-9 (FSR-) - Body ground



NG
REPLACE NO. 2 FLOOR WIRE
OK

REPLACE FRONT SEAT WIRE RH 

8.CHECK FOR DTC (CENTER AIRBAG SENSOR)


    C146230E10
  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch OFF.

  1. Turn the ignition switch ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1650 is not output.

    HINT:
    Codes other than DTC B1650 maybe output at this time, but they are not related to this check.



NG
Go to step 9
OK

USE SIMULATION METHOD TO CHECK (Click here)  

9.CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch OFF.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor and the occupant classification ECU.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


10.CHECK CONNECTORS
  1. Disconnect the connectors from the center airbag sensor and the occupant classification ECU.

  1. Check that the connectors (on the center airbag sensor side and occupant classification ECU side) are not damaged.

    OK:
    The connectors are not damaged or damaged.



NG
REPLACE HARNESS AND CONNECTOR
OK


11.CHECK NO. 2 FLOOR WIRE (CENTER AIRBAG SENSOR - OCCUPANT CLASSIFICATION ECU)

C159568E01

  1. Using a service wire, connect terminal 12 (FSP+) and 13 (FSP-) of connector B.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    Q11-4 (FSR-) - Q11-8 (FSR+)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    Q11-4 (FSR-) - Q11-8 (FSR+)
    Always
    1 MΩ or higher
    Q11-4 (FSR-) - Body ground
    Q11-8 (FSR+) - Body ground

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    Q11-4 (FSR-) - Body ground
    Ignition switch ON
    Below 1 V
    Q11-8 (FSR+) - Body ground

    Result 
    Result
    Proceed to
    NG
    A
    OK (for Column Shift Type)
    B
    OK (for Floor Shift Type)
    C



A
REPLACE NO. 2 FLOOR WIRE

B
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
C

REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)