Home › BODY ELECTRICAL › NAVIGATION › NAVIGATION SYSTEM (for Double Cab)

DTC    74-40    Short in Speaker Circuit

for Preparation Click here


DESCRIPTION


DTC No.
DTC Detection Condition
Trouble Area
74-40
A short is detected in the speaker output circuit
  1. Harness and connector
  2. Speaker
  3. Stereo component amplifier

WIRING DIAGRAM


E146449E01


E146450E01


INSPECTION PROCEDURE

1.CHECK DTC
  1. Disconnect the K16 and K17 amplifier connectors.

  1. Clear the DTC.

  1. Check if DTC 74-40 is output.

    OK:
    DTC 74-40 is not output.



NG
REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY (Click here)
OK


2.CHECK DTC
  1. Reconnect the K16 amplifier connector.

  1. Check if DTC 74-40 is output.

    OK:
    DTC 74-40 is not output.



NG
Go to step 7
OK


3.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - SPEAKERS)
  1. Disconnect the K17 amplifier connector.



    E145809E01
  1. Disconnect the N10, M8, K14 and P14 speaker connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    K17-1 (WFL-) - N10-2
    Always
    Below 1 Ω
    K17-2 (WFL+) - N10-1
    K17-3 (WFR-) - M8-2
    K17-9 (WFR+) - M8-1
    K17-4 (CTR+) - K14-1
    K17-10 (CTR-) - K14-2
    K17-5 (WF1+) - P14-1
    K17-12 (WF1-) - P14-2
    K17-2 (WFL+) - Body ground
    Always
    10 kΩ or higher
    K17-1 (WFL-) - Body ground
    K17-9 (WFR+) - Body ground
    K17-3 (WFR-) - Body ground
    K17-5 (WF1+) - Body ground
    K17-12 (WF1-) - Body ground
    K17-4 (CTR+) - Body ground
    K17-10 (CTR-) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT FRONT NO. 1 SPEAKER LH
  1. Disconnect the N10 speaker connector.



    E110243E09
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    1.5 to 2.1 Ω



NG
REPLACE FRONT NO. 1 SPEAKER LH (Click here)
OK


5.INSPECT FRONT NO. 1 SPEAKER RH
  1. Disconnect the M8 speaker connector.



    E110243E10
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    1.5 to 2.1 Ω



NG
REPLACE FRONT NO. 1 SPEAKER RH (Click here)
OK


6.INSPECT FRONT NO. 4 SPEAKER


    E145812E01
  1. Disconnect the K14 speaker connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    1.5 to 2.1 Ω



NG
REPLACE FRONT NO. 4 SPEAKER (Click here)
OK

REPLACE BOX SPEAKER (Click here)  

7.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - SPEAKERS)


    E145811E01
  1. Disconnect the K16 amplifier connector.

  1. Disconnect the K10, K12, N1, M1, O1 and O7 speaker connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    K16-6 (FR-) - K10-4 (TWR-)
    Always
    Below 1 Ω
    K16-2 (FR+) - K10-3 (TWR+)
    K16-7 (FL-) - K12-4 (TWL-)
    K16-8 (FL+) - K12-3 (TWL+)
    K10-2 (-) - M1-1
    K10-1 (+) - M1-3
    K12-2 (-) - N1-1
    K12-1 (+) - N1-3
    K16-4 (RR-) - O1-2
    K16-10 (RR+) - O1-1
    K16-9 (RL-) - O7-2
    K16-3 (RL+) - O7-1
    K16-8 (FL+) - Body ground
    Always
    10 kΩ or higher
    K16-7 (FL-) - Body ground
    K16-2 (FR+) - Body ground
    K16-6 (FR-) - Body ground
    K16-3 (RL+) - Body ground
    K16-9 (RL-) - Body ground
    K16-10 (RR+) - Body ground
    K16-4 (RR-) - Body ground
    K10-2 (-) - Body ground
    K10-1 (+) - Body ground
    K12-2 (-) - Body ground
    K12-1 (+) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.INSPECT FRONT NO. 3 SPEAKER LH


    E145813E01
  1. Disconnect the N1 speaker connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 3
    Always
    2.5 to 3.5 Ω



NG
REPLACE FRONT NO. 3 SPEAKER LH (Click here)
OK


9.INSPECT FRONT NO. 3 SPEAKER RH


    E145813E03
  1. Disconnect the M1 speaker connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 3
    Always
    2.5 to 3.5 Ω



NG
REPLACE FRONT NO. 3 SPEAKER RH (Click here)
OK


10.INSPECT FRONT NO. 2 SPEAKER LH


    E144969E04
  1. Disconnect the K12 speaker connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    3 (TWL+) - 4 (TWL-)
    Always
    1.3 to 2.3 Ω
    1 (+) - 3 (TWL+)
    Always
    Below 1 Ω
    2 (-) - 4 (TWL-)



NG
REPLACE FRONT NO. 2 SPEAKER LH (Click here)
OK


11.INSPECT FRONT NO. 2 SPEAKER RH


    E144969E05
  1. Disconnect the K10 speaker connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    3 (TWR+) - 4 (TWR-)
    Always
    1.3 to 2.3 Ω
    1 (+) - 3 (TWR+)
    Always
    Below 1 Ω
    2 (-) - 4 (TWR-)



NG
REPLACE FRONT NO. 2 SPEAKER RH (Click here)
OK


12.INSPECT REAR NO. 1 SPEAKER LH


    E110243E11
  1. Disconnect the O7 speaker connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    1.5 to 2.1 Ω



NG
REPLACE REAR NO. 1 SPEAKER LH (Click here)
OK

REPLACE REAR NO. 1 SPEAKER RH (Click here)