DTC P0300 Random / Multiple Cylinder Misfire Detected |
DTC P0301 Cylinder 1 Misfire Detected |
DTC P0302 Cylinder 2 Misfire Detected |
DTC P0303 Cylinder 3 Misfire Detected |
DTC P0304 Cylinder 4 Misfire Detected |
DTC P0305 Cylinder 5 Misfire Detected |
DTC P0306 Cylinder 6 Misfire Detected |

| *1 | VVT Sensor |
| *2 | Crankshaft Position Sensor |
| *3 | ECM |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0300 | Simultaneous misfiring of several cylinders occurs and one of the following conditions below is detected (2 trip detection logic):
|
|
| P0301 P0302 P0303 P0304 P0305 P0306 | Misfiring of specific cylinder occurs and one of the following conditions below is detected (2 trip detection logic):
|
| Related DTCs | P0300: Multiple cylinder misfire P0301: Cylinder 1 misfire P0302: Cylinder 2 misfire P0303: Cylinder 3 misfire P0304: Cylinder 4 misfire P0305: Cylinder 5 misfire P0306: Cylinder 6 misfire |
| Required Sensors/Components (Main) | Crankshaft position sensor and VVT sensor |
| Required Sensors/Components (Related) | Engine coolant temperature, intake air temperature sensors and mass air flow meter |
| Frequency of Operation | Continuous |
| Duration | 1000 crankshaft revolutions (soon after engine is started: 1 time, other 4 times) (Emissions-related misfire) 200 crankshaft revolutions (1 or 3 times) (Catalyst-damaging misfire) |
| MIL Operation | 2 driving cycles: MIL illuminates when misfire detected MIL flashes immediately: When catalyst-damaging misfire occurs |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not stored | P0016, P0018 (VVT system - Misalignment) P0017, P0019 (Exhaust VVT system - Misalignment) P0102, P0103 (Mass air flow meter) P0112, P0113 (Intake air temperature sensor) P0115, P0117, P0118 (Engine coolant temperature sensor) P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor) P0125 (Insufficient coolant temperature for closed loop fuel control) P0327, P0328, P0332, P0333 (Knock sensor) P0335 (Crankshaft position sensor) P0340 (VVT sensor) P0351 - P0356 (Igniter) P0500 (Vehicle speed sensor) P0705 (Shift lever position switch) |
| Battery voltage | 8 V or higher |
| VVT system | Not operated by scan tool |
| Engine speed | 400 to 5900 rpm |
| Either of following conditions (a) or (b) met | - |
| (a) Engine coolant temperature at engine start | Higher than -7°C (19°F) |
| (b) Engine coolant temperature | Higher than 20°C (68°F) |
| Fuel cut | OFF |
| First 1000 revolutions after engine start, or Check Mode | 1000 crankshaft revolutions |
| Except above | 1000 crankshaft revolutions x 4 |
| All of following conditions 1, 2, 3 and 4 met | 200 crankshaft revolutions x 3 |
| Except above (MIL blinks immediately) | Crankshaft 200 revolutions |
| 1. Driving cycle | 1st |
| 2. Check mode | OFF |
| 3. Engine speed | Less than 1900 rpm |
| 4. Intake air amount per revolution | Less than 1.4 g/rev |
| Misfire rate | 1.5% or more |
| Number of misfires per 200 revolutions | 77 or more (varies with intake air amount and engine speed) |
| Paired cylinders misfire (MIL blinks immediately) | Detected |
| Engine Speed | Duration |
| Idling | 8.0 minutes or more |
| 1000 | 4.5 minutes or more |
| 2000 | 2.5 minutes or more |
| 3000 | 1.5 minutes or more |
| 1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO MISFIRE CODES) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| P0300, P0301, P0302, P0303, P0304, P0305 and/or P0306 is output | A |
| P0300, P0301, P0302, P0303, P0304, P0305 and/or P0306 and other DTCs are output | B |
|
| ||||
| A | |
| 2.CHECK PCV HOSE CONNECTIONS |
Check the PCV hose connections .
|
| ||||
| OK | |
| 3.READ VALUE USING TECHSTREAM (MISFIRE RPM AND MISFIRE LOAD) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Misfire RPM and Misfire Load.
Read and note the Misfire RPM and Misfire Load values.
| NEXT | |
| 4.READ VALUE USING TECHSTREAM |
Enter the following menus: Powertrain / Engine and ECT / Data List / Catalyst OT MF F/C.
Read the value displayed on the Techstream.
| Data List | Techstream Display | Proceed to |
| Catalyst OT MF F/C | AVAIL (Avail) | A |
| NOT AVL (Not Avl) | B |
|
| ||||
| A | |
| 5.PERFORM ACTIVE TEST USING TECHSTREAM |
Enter the following menus: Powertrain / Engine and ECT / Active Test / Prohibit the Catalyst OT Misfire prevent F/C.
Perform the Active Test.
| NEXT | |
| 6.READ VALUE USING TECHSTREAM (MISFIRE COUNT) |
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Cylinder #1 Misfire Count, #2, #3, #4, #5 and #6.
Allow the engine to idle.
Read the values for Cylinder #1 Misfire Count to Cylinder #6 Misfire Count displayed on the Techstream. If no misfires are counted in any cylinders, perform the following procedure:
Move the shift lever to D.
Check Cylinder #1 Misfire Count to Cylinder #6 Misfire Count.
If misfires are still not being counted, perform procedures "A" and "B", and then check the misfire counts again.
Procedure A: Drive the vehicle while matching the vehicle conditions to the Misfire RPM and Misfire Load values noted in the "Read Value Using Techstream (Misfire RPM and Misfire Load)" procedure above.
Procedure B: Read Cylinder #1 Misfire Count to Cylinder #6 Misfire Count or the DTCs output on the Techstream.
| Result | Proceed to |
| Most misfires occur in only 1 or 2 cylinders | A |
| 3 cylinders or more have equal misfire counts | B |
|
| ||||
| A | |
| 7.INSPECT SPARK PLUG |
Inspect the spark plug of the misfiring cylinder .
|
| ||||
| OK | |
| 8.CHECK FOR SPARKS AND IGNITION |
Perform a spark test .
| NEXT | |
| 9.CHECK CYLINDER COMPRESSION PRESSURE |
Measure the cylinder compression pressure of the misfiring cylinder .
|
| ||||
| OK | |
| 10.CHECK FUEL INJECTOR ASSEMBLY (POWER SOURCE) |
![]() |
Disconnect the fuel injector assembly connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Cylinder | Tester Connection | Switch Condition | Specified Condition |
| No. 1 | D11-1 - Body ground | Ignition switch ON | 11 to 14 V |
| No. 2 | D26-1 - Body ground | Ignition switch ON | 11 to 14 V |
| No. 3 | D13-1 - Body ground | Ignition switch ON | 11 to 14 V |
| No. 4 | D24-1 - Body ground | Ignition switch ON | 11 to 14 V |
| No. 5 | D15-1 - Body ground | Ignition switch ON | 11 to 14 V |
| No. 6 | D22-1 - Body ground | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector (to Fuel Injector Assembly) |
Turn the ignition switch off.
|
| ||||
| OK | |
| 11.CHECK HARNESS AND CONNECTOR |
Disconnect the fuel injector assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Cylinder | Tester Connection | Condition | Specified Condition |
| No. 1 | D11-2 - Body ground | Always | 10 kΩ or higher |
| D11-2 - D74-86 (#10) | Always | Below 1 Ω | |
| No. 2 | D26-2 - Body ground | Always | 10 kΩ or higher |
| D26-2 - D74-109 (#20) | Always | Below 1 Ω | |
| No. 3 | D13-2 - Body ground | Always | 10 kΩ or higher |
| D13-2 - D74-85 (#30) | Always | Below 1 Ω | |
| No. 4 | D24-2 - Body ground | Always | 10 kΩ or higher |
| D24-2 - D74-108 (#40) | Always | Below 1 Ω | |
| No. 5 | D15-2 - Body ground | Always | 10 kΩ or higher |
| D15-2 - D74-84 (#50) | Always | Below 1 Ω | |
| No. 6 | D22-2 - Body ground | Always | 10 kΩ or higher |
| D22-2 - D74-107 (#60) | Always | Below 1 Ω |
|
| ||||
| OK | |
| 12.CHECK FUEL INJECTOR ASSEMBLY OF MISFIRING CYLINDER |
Check the fuel injector injection [whether fuel volume is high or low, and whether injection pattern is poor] .
|
| ||||
| OK | |
| 13.CHECK INTAKE SYSTEM |
Check the intake system for vacuum leakage .
|
| ||||
| OK | |
| 14.CHECK FUEL PRESSURE |
Check the fuel pressure .
|
| ||||
| OK | |
| 15.READ VALUE USING TECHSTREAM (COOLANT TEMP) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.
Read Coolant Temp twice, when the engine is both cold and warmed up.
|
| ||||
| OK | |
| 16.READ VALUE USING TECHSTREAM (MAF) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF and Coolant Temp.
Allow the engine to idle until Coolant Temp reaches 75°C (167°F) or higher.
Read MAF with the engine speed at 3000 rpm.
|
| ||||
| OK | |
| 17.CHECK VALVE TIMING |
![]() |
Remove the cylinder head cover RH and LH.
Turn the crankshaft pulley and align its groove with the "0" timing mark on the timing chain cover.
Check that the timing marks on the camshaft timing gears are aligned with the timing marks of the bearing cap as shown in the illustration.
| *1 | Timing Mark |
Reinstall the cylinder head cover RH and LH.
|
| ||||
|
| ||||
| 18.CHECK INTAKE SYSTEM |
Check the intake system for vacuum leakage .
|
| ||||
| OK | |
| 19.CHECK FUEL PRESSURE |
Check the fuel pressure .
|
| ||||
| OK | |
| 20.READ VALUE USING TECHSTREAM (COOLANT TEMP) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.
Read Coolant Temp twice, when the engine is both cold and warmed up.
|
| ||||
| OK | |
| 21.READ VALUE USING TECHSTREAM (MAF) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF and Coolant Temp.
Allow the engine to idle until Coolant Temp reaches 75°C (167°F) or higher.
Read MAF with the engine speed at 3000 rpm.
|
| ||||
| OK | |
| 22.CHECK VALVE TIMING |
![]() |
Remove the cylinder head cover RH and LH.
Turn the crankshaft pulley and align its groove with the "0" timing mark on the timing chain cover.
Check that the timing marks on the camshaft timing gears are aligned with the timing marks of the bearing cap as shown in the illustration.
| *1 | Timing Mark |
Reinstall the cylinder head cover RH and LH.
|
| ||||
| OK | |
| 23.INSPECT SPARK PLUG |
Inspect the spark plug of the misfiring cylinder .
|
| ||||
| OK | |
| 24.CHECK FOR SPARKS AND IGNITION |
Perform a spark test .
| NEXT | |
| 25.CHECK CYLINDER COMPRESSION PRESSURE |
Measure the cylinder compression pressure of the misfiring cylinder .
|
| ||||
| OK | |
| 26.CHECK FUEL INJECTOR ASSEMBLY (POWER SOURCE) |
![]() |
Disconnect the fuel injector assembly connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Cylinder | Tester Connection | Switch Condition | Specified Condition |
| No. 1 | D11-1 - Body ground | Ignition switch ON | 11 to 14 V |
| No. 2 | D26-1 - Body ground | Ignition switch ON | 11 to 14 V |
| No. 3 | D13-1 - Body ground | Ignition switch ON | 11 to 14 V |
| No. 4 | D24-1 - Body ground | Ignition switch ON | 11 to 14 V |
| No. 5 | D15-1 - Body ground | Ignition switch ON | 11 to 14 V |
| No. 6 | D22-1 - Body ground | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector (to Fuel Injector Assembly) |
Turn the ignition switch off.
|
| ||||
| OK | |
| 27.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - ECM) |
Disconnect the fuel injector assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Cylinder | Tester Connection | Condition | Specified Condition |
| No. 1 | D11-2 - Body ground | Always | 10 kΩ or higher |
| D11-2 - D74-86 (#10) | Always | Below 1 Ω | |
| No. 2 | D26-2 - Body ground | Always | 10 kΩ or higher |
| D26-2 - D74-109 (#20) | Always | Below 1 Ω | |
| No. 3 | D13-2 - Body ground | Always | 10 kΩ or higher |
| D13-2 - D74-85 (#30) | Always | Below 1 Ω | |
| No. 4 | D24-2 - Body ground | Always | 10 kΩ or higher |
| D24-2 - D74-108 (#40) | Always | Below 1 Ω | |
| No. 5 | D15-2 - Body ground | Always | 10 kΩ or higher |
| D15-2 - D74-84 (#50) | Always | Below 1 Ω | |
| No. 6 | D22-2 - Body ground | Always | 10 kΩ or higher |
| D22-2 - D74-107 (#60) | Always | Below 1 Ω |
|
| ||||
| OK | |
| 28.CHECK FUEL INJECTOR ASSEMBLY OF MISFIRING CYLINDER |
Check the fuel injector injection [whether fuel volume is high or low, and whether injection pattern is poor] .
|
| ||||
| OK | |
| 29.CHECK HARNESS AND CONNECTOR |
Check the connection and terminal contact pressure of the connectors and wire harnesses between the mass air flow meter and ECM (Click here).
| NEXT | |
| 30.CHECK WHETHER DTC OUTPUT RECURS |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON and turn the Techstream on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0300, P0301, P0302, P0303, P0304, P0305 or P0306.
Check the DTC judgment result.
| Result | Proceed to |
| ABNORMAL (P0300, P0301, P0302, P0303, P0304, P0305 or P0306 is output) | A |
| NORMAL (No DTC is output) | B |
|
| ||||
| A | |
| 31.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM) |
Disconnect the mass air flow meter connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D7-5 (VG) - D74-74 (VG) | Always | Below 1 Ω |
| D7-4 (E2G) - D74-75 (E2G) | Always | Below 1 Ω |
| D7-5 (VG) or D74-74 (VG) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 32.REPLACE MASS AIR FLOW METER |
Replace the mass air flow meter (Click here).
| NEXT | |
| 33.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON and turn the Techstream on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0300, P0301, P0302, P0303, P0304, P0305 or P0306.
Check the DTC judgment result.
| Result | Proceed to |
| NORMAL (No DTC is output) | A |
| ABNORMAL (P0300, P0301, P0302, P0303, P0304, P0305 or P0306 is output) | B |
|
| ||||
| A | ||
| ||
| 34.CHECK FUEL LINE |
Check the fuel lines for leaks or blockage.
|
| ||||
| OK | ||
| ||