DTC C2121/21 No Signal from Transmitter ID1 |
DTC C2122/22 No Signal from Transmitter ID2 |
DTC C2123/23 No Signal from Transmitter ID3 |
DTC C2124/24 No Signal from Transmitter ID4 |
DTC C2181/81 Transmitter ID1 not Received (Test Mode DTC) |
DTC C2182/82 Transmitter ID2 not Received (Test Mode DTC) |
DTC C2183/83 Transmitter ID3 not Received (Test Mode DTC) |
DTC C2184/84 Transmitter ID4 not Received (Test Mode DTC) |
| DTC Code | DTC Detection Condition | Trouble Area |
| C2121/21 C2122/22 C2123/23 C2124/24 | When all conditions below are met:
|
|
| C2181/81 C2182/82 C2183/83 C2184/84 | Test mode procedure is performed. |
|

| 1.READ OUTPUT DTC (DTC C2174/74) |
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and the Techstream on.
Enter the following menus: Chassis / Tire Pressure Monitor / Trouble Codes.
Read DTCs.
| Result | Proceed to |
| DTC C2174/74 is not output | A |
| DTC C2174/74 is output | B |
|
| ||||
| A | |
| 2.CHECK FREQUENCY RECEIVING CONDITION |
Check if the vehicle is in conditions such as the ones described below:
Facilities or devices that use similar radio frequencies are located in the vicinity of the vehicle.
Devices using similar radio frequencies are used in the vehicle.
|
| ||||
| OK | |
| 3.IDENTIFY TRANSMITTER CORRESPONDING TO DTC |
Set the tire pressures to the appropriate specified value(s) (Click here).
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and the Techstream on.
Enter the following menus: Chassis / Tire Pressure Monitor / Data List.
Check the values by referring to the table below.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| ID 1 Tire Inflation Pressure | ID1 tire inflation pressure / min.: Absolute pressure / 100.00 kPa (1 kgf/cm2, 14 psi), Relative pressure / 0 kPa (0 kgf/cm2, 0 psi) max.: Absolute pressure / 449.35 kPa (4.5 kgf/cm2, 63 psi), Relative pressure / 349.35 kPa (3.6 kgf/cm2, 51 psi) | Actual tire inflation pressure | If 100 kPa (1 kgf/cm2, 14 psi) for the absolute pressure or 0 kPa (0 kgf/cm2, 0 psi) is displayed for the relative pressure, the data has not been received.* |
| ID 2 Tire Inflation Pressure | ID2 tire inflation pressure / min.: Absolute pressure / 100.00 kPa (1 kgf/cm2, 14 psi), Relative pressure / 0 kPa (0 kgf/cm2, 0 psi) max.: Absolute pressure / 449.35 kPa (4.5 kgf/cm2, 63 psi), Relative pressure / 349.35 kPa (3.6 kgf/cm2, 51 psi) | Actual tire inflation pressure | If 100 kPa (1 kgf/cm2, 14 psi) for the absolute pressure or 0 kPa (0 kgf/cm2, 0 psi) is displayed for the relative pressure, the data has not been received.* |
| ID 3 Tire Inflation Pressure | ID3 tire inflation pressure / min.: Absolute pressure / 100.00 kPa (1 kgf/cm2, 14 psi), Relative pressure / 0 kPa (0 kgf/cm2, 0 psi) max.: Absolute pressure / 449.35 kPa (4.5 kgf/cm2, 63 psi), Relative pressure / 349.35 kPa (3.6 kgf/cm2, 51 psi) | Actual tire inflation pressure | If 100 kPa (1 kgf/cm2, 14 psi) for the absolute pressure or 0 kPa (0 kgf/cm2, 0 psi) is displayed for the relative pressure, the data has not been received.* |
| ID 4 Tire Inflation Pressure | ID4 tire inflation pressure / min.: Absolute pressure / 100.00 kPa (1 kgf/cm2, 14 psi), Relative pressure / 0 kPa (0 kgf/cm2, 0 psi) max.: Absolute pressure / 449.35 kPa (4.5 kgf/cm2, 63 psi), Relative pressure / 349.35 kPa (3.6 kgf/cm2, 51 psi) | Actual tire inflation pressure | If 100 kPa (1 kgf/cm2, 14 psi) for the absolute pressure or 0 kPa (0 kgf/cm2, 0 psi) is displayed for the relative pressure, the data has not been received.* |
Rapidly reduce the tire pressure for each tire at least 40 kPa (0.4 kgf/cm2, 5.8 psi) within 30 seconds.
Check the Data List.
After confirming that the "ID Tire Inflation Pressure" data for one tire (ID1 to ID4) has changed, repeat this procedure for the other tires. Identify the transmitter that corresponds to the DTC.
| Condition | Proceed to |
| All abnormal | A |
| One or more transmitters are abnormal | B |
| All normal | C |
|
| ||||
|
| ||||
| A | |
| 4.CHECK HARNESS AND CONNECTOR (ECU - RECEIVER) |
Disconnect the J31 ECU connector.
Disconnect the P17 receiver connector.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| J31-12 (RDA) - P17-1 (RDA) | Always | Below 1 Ω |
| J31-11 (GND2) - P17-4 (GND) | Always | Below 1 Ω |
| J31-6 (RF5V) - P17-5 (+5V) | Always | Below 1 Ω |
| J31-12 (RDA) - Body ground | Always | 10 kΩ or higher |
| J31-11 (GND2) - Body ground | Always | 10 kΩ or higher |
| J31-6 (RF5V) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 5.CHECK TRANSMITTER ID |
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and the Techstream on.
Enter the following menus: Chassis / Tire Pressure Monitor / Data List.
Check the values by referring to the table below.
| Tester Display | Measurement Item/Display | Normal Condition | Diagnostic Note |
| Registered ID1 Code | Registered ID1 code/ min.: 0 max.: FFFFFFFF* | The transmitter ID registered in the transmitter ID1 is displayed | *: Displayed only when the transmitter ID is not registered. |
| Registered ID2 Code | Registered ID2 code/ min.: 0 max.: FFFFFFFF* | The transmitter ID registered in the transmitter ID2 is displayed | *: Displayed only when the transmitter ID is not registered. |
| Registered ID3 Code | Registered ID3 code/ min.: 0 max.: FFFFFFFF* | The transmitter ID registered in the transmitter ID3 is displayed | *: Displayed only when the transmitter ID is not registered. |
| Registered ID4 Code | Registered ID4 code/ min.: 0 max.: FFFFFFFF* | The transmitter ID registered in the transmitter ID4 is displayed | *: Displayed only when the transmitter ID is not registered. |
Check the transmitter ID on the identified transmitter by removing it from the tire and wheel.

Confirm that the transmitter ID on the transmitter and recorded transmitter ID match.
| Result | Proceed to |
| Match | A |
| Do not match | B |
|
| ||||
| A | |
| 6.REPLACE TIRE PRESSURE WARNING VALVE AND TRANSMITTER |
Replace the tire pressure warning valve and transmitter (Click here).
| NEXT | |
| 7.REGISTRATION OF TRANSMITTER ID |
Perform registration (Click here).
| NEXT | |
| 8.PERFORM INITIALIZATION |
Perform initialization (Click here).
| NEXT | |
| 9.CONFIRM TIRE INFLATION PRESSURE (DATA LIST) |
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and the Techstream on.
Enter the following menus: Chassis / Tire Pressure Monitor / Data List.
Check the values by referring to the table below.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| ID 1 Tire Inflation Pressure | ID1 tire inflation pressure / min.: Absolute pressure / 100.00 kPa (1 kgf/cm2, 14 psi), Relative pressure / 0 kPa (0 kgf/cm2, 0 psi) max.: Absolute pressure / 449.35 kPa (4.5 kgf/cm2, 63 psi), Relative pressure / 349.35 kPa (3.6 kgf/cm2, 51 psi) | Actual tire inflation pressure | If 100 kPa (1 kgf/cm2, 14 psi) for the absolute pressure or 0 kPa (0 kgf/cm2, 0 psi) is displayed for the relative pressure, the data has not been received.* |
| ID 2 Tire Inflation Pressure | ID2 tire inflation pressure / min.: Absolute pressure / 100.00 kPa (1 kgf/cm2, 14 psi), Relative pressure / 0 kPa (0 kgf/cm2, 0 psi) max.: Absolute pressure / 449.35 kPa (4.5 kgf/cm2, 63 psi), Relative pressure / 349.35 kPa (3.6 kgf/cm2, 51 psi) | Actual tire inflation pressure | If 100 kPa (1 kgf/cm2, 14 psi) for the absolute pressure or 0 kPa (0 kgf/cm2, 0 psi) is displayed for the relative pressure, the data has not been received.* |
| ID 3 Tire Inflation Pressure | ID3 tire inflation pressure / min.: Absolute pressure / 100.00 kPa (1 kgf/cm2, 14 psi), Relative pressure / 0 kPa (0 kgf/cm2, 0 psi) max.: Absolute pressure / 449.35 kPa (4.5 kgf/cm2, 63 psi), Relative pressure / 349.35 kPa (3.6 kgf/cm2, 51 psi) | Actual tire inflation pressure | If 100 kPa (1 kgf/cm2, 14 psi) for the absolute pressure or 0 kPa (0 kgf/cm2, 0 psi) is displayed for the relative pressure, the data has not been received.* |
| ID 4 Tire Inflation Pressure | ID4 tire inflation pressure / min.: Absolute pressure / 100.00 kPa (1 kgf/cm2, 14 psi), Relative pressure / 0 kPa (0 kgf/cm2, 0 psi) max.: Absolute pressure / 449.35 kPa (4.5 kgf/cm2, 63 psi), Relative pressure / 349.35 kPa (3.6 kgf/cm2, 51 psi) | Actual tire inflation pressure | If 100 kPa (1 kgf/cm2, 14 psi) for the absolute pressure or 0 kPa (0 kgf/cm2, 0 psi) is displayed for the relative pressure, the data has not been received.* |
| Result | Proceed to |
| Tire pressure values are not displayed. | A |
| All tire pressure readings are equal to specified values. | B |
|
| ||||
| A | |
| 10.REPLACE TIRE PRESSURE WARNING ANTENNA AND RECEIVER |
Replace the tire pressure warning antenna and receiver (Click here).
| NEXT | |
| 11.CONFIRM TIRE INFLATION PRESSURE (DATA LIST) |
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and the Techstream on.
Enter the following menus: Chassis / Tire Pressure Monitor / Data List.
Check the values by referring to the table below.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| ID 1 Tire Inflation Pressure | ID1 tire inflation pressure / min.: Absolute pressure / 100.00 kPa (1 kgf/cm2, 14 psi), Relative pressure / 0 kPa (0 kgf/cm2, 0 psi) max.: Absolute pressure / 449.35 kPa (4.5 kgf/cm2, 63 psi), Relative pressure / 349.35 kPa (3.6 kgf/cm2, 51 psi) | Actual tire inflation pressure | If 100 kPa (1 kgf/cm2, 14 psi) for the absolute pressure or 0 kPa (0 kgf/cm2, 0 psi) is displayed for the relative pressure, the data has not been received.* |
| ID 2 Tire Inflation Pressure | ID2 tire inflation pressure / min.: Absolute pressure / 100.00 kPa (1 kgf/cm2, 14 psi), Relative pressure / 0 kPa (0 kgf/cm2, 0 psi) max.: Absolute pressure / 449.35 kPa (4.5 kgf/cm2, 63 psi), Relative pressure / 349.35 kPa (3.6 kgf/cm2, 51 psi) | Actual tire inflation pressure | If 100 kPa (1 kgf/cm2, 14 psi) for the absolute pressure or 0 kPa (0 kgf/cm2, 0 psi) is displayed for the relative pressure, the data has not been received.* |
| ID 3 Tire Inflation Pressure | ID3 tire inflation pressure / min.: Absolute pressure / 100.00 kPa (1 kgf/cm2, 14 psi), Relative pressure / 0 kPa (0 kgf/cm2, 0 psi) max.: Absolute pressure / 449.35 kPa (4.5 kgf/cm2, 63 psi), Relative pressure / 349.35 kPa (3.6 kgf/cm2, 51 psi) | Actual tire inflation pressure | If 100 kPa (1 kgf/cm2, 14 psi) for the absolute pressure or 0 kPa (0 kgf/cm2, 0 psi) is displayed for the relative pressure, the data has not been received.* |
| ID 4 Tire Inflation Pressure | ID4 tire inflation pressure / min.: Absolute pressure / 100.00 kPa (1 kgf/cm2, 14 psi), Relative pressure / 0 kPa (0 kgf/cm2, 0 psi) max.: Absolute pressure / 449.35 kPa (4.5 kgf/cm2, 63 psi), Relative pressure / 349.35 kPa (3.6 kgf/cm2, 51 psi) | Actual tire inflation pressure | If 100 kPa (1 kgf/cm2, 14 psi) for the absolute pressure or 0 kPa (0 kgf/cm2, 0 psi) is displayed for the relative pressure, the data has not been received.* |
| Result | Proceed to |
| Tire pressure values are not displayed. | A |
| All tire pressure readings are equal to specified values. | B |
|
| ||||
| A | ||
| ||