Home › ENGINE · 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0500    Vehicle Speed Sensor "A"

for Preparation Click here


DESCRIPTION

The speed sensor detects the wheel speed and sends the appropriate signals to the skid control ECU. The skid control ECU converts these wheel speed signals into a pulse signal and outputs it to the ECM via the combination meter. The ECM determines the vehicle speed based on the frequency of this pulse signal.

A115899E20


DTC No.
DTC Detection Condition
Trouble Area
P0500
While the vehicle is being driven, a vehicle speed sensor signal is not being transmitted to the ECM (2 trip detection logic).
  1. Open or short in speed signal circuit
  2. Speedometer circuit (wheel speed sensor, skid control ECU)
  3. Combination meter assembly
  4. ECM
  5. Wire harness or connector

MONITOR DESCRIPTION

The ECM assumes that the vehicle is being driven when the vehicle speed measured by the output speed sensor (SP2) is more than 9 km/h (5.6 mph). If there is no speed signal from the combination meter despite this condition being met, the ECM interprets this as a malfunction in the speed signal circuit. The ECM then illuminates the MIL and stores the DTC.

MONITOR STRATEGY


Related DTCs
P0500: Vehicle speed sensor "A" pulse input error
Required Sensors/Components (Main)
Wheel speed sensor, Combination meter assembly and Skid control ECU
Required Sensors/Components (Related)
Output speed sensor (SP2)
Frequency of Operation
Continuous
Duration
5 seconds
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not stored
None
Time after ignition switch is turned from off to ON
3 seconds or more
Vehicle speed at output speed sensor
9 km/h (5.59 mph) or more
Battery voltage
8 V or higher
Ignition switch
ON
Starter
OFF

TYPICAL MALFUNCTION THRESHOLDS


Vehicle speed sensor signal
No pulse input

CONFIRMATION DRIVING PATTERN


A198825E17

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on [A].
  6. Start the engine.
  7. Drive the vehicle at 24 km/h (15 mph) or more for a total of 30 seconds or more [B].
  8. Stop the vehicle.
  9. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].
  10. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  11. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  12. Input the DTC: P0500.
  13. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    If the judgment result shows ABNORMAL, the system has a malfunction.

  14. If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM


A237393E06


INSPECTION PROCEDURE

HINT:
Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK OPERATION OF SPEEDOMETER
  1. Drive the vehicle and check whether the operation of the speedometer in the combination meter is normal.

    HINT:
    1. The vehicle speed sensor is operating normally if the speedometer reading is normal.
    2. If the speedometer does not operate, check it by following the procedure described in Speedometer Malfunction.



NG
GO TO MALFUNCTION IN SPEEDOMETER (Click here)
OK


2.READ VALUE USING TECHSTREAM (VEHICLE SPEED)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Vehicle Speed.

  1. Drive the vehicle.

  1. Read the value displayed on the Techstream.

    OK:
    Vehicle speeds displayed on the Techstream and speedometer display are equal.



NG
Go to step 3
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
  1. Disconnect the combination meter connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    J28-35 (+S) - A24-13 (SPD)
    Always
    Below 1 Ω
    J28-35 (+S) or A24-13 (SPD) - Body ground
    Always
    10 kΩ or higher

    HINT:
    If the wire harness has a short, check the speed signal circuit in other systems related to the vehicle speed signal (e.g. tire pressure warning system, audio system, etc.).



NG
CHECK ALL SYSTEMS RELATED TO SPEED SENSOR SIGNAL AND REPAIR OR REPLACE MALFUNCTIONING HARNESS OR CONNECTOR
OK


4.CHECK COMBINATION METER ASSEMBLY (+S VOLTAGE)
A127854E83
  1. Disconnect the combination meter assembly connector.

    HINT:
    Disconnect the ECU connectors of other systems related to the speed signal, but do not disconnect the ECM connectors.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    J28-35 (+S) - Body ground
    Ignition switch ON
    4.5 to 5.5 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Combination Meter Assembly)



NG
REPLACE ECM (Click here)
OK


5.CHECK COMBINATION METER (SPD SIGNAL OUTPUT WAVEFORM)
A291061E01
  1. Remove the combination meter assembly.

  1. Connect the combination meter assembly connector.

  1. Move the shift lever to N.

  1. Jack up the vehicle.

  1. Turn the ignition switch to ON.

  1. Check the voltage between the terminal of the combination meter assembly and body ground while the wheels are turned slowly.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    J28-35 (+S) - Body ground
    Ignition switch ON
    (Wheels turned slowly)
    Voltage generated intermittently

    Text in Illustration 
    *a
    Component with harness connected
    (Combination Meter Assembly)
    *b
    Wheels Turned

    HINT:
    1. The output voltage fluctuates up and down, similarly to the diagram, when the wheels are turned slowly.
    2. A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly.



NG
Go to step 6
OK

REPLACE ECM (Click here)  

6.CHECK COMBINATION METER ASSEMBLY (SPD SIGNAL INPUT WAVEFORM)
A291061E03
  1. Remove the combination meter assembly.

  1. Connect the combination meter assembly connector.

  1. Move the shift lever to N.

  1. Jack up the vehicle.

  1. Turn the ignition switch to ON.

  1. Check the voltage between the terminal of the combination meter assembly and body ground while the wheels are turned slowly.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    J28-36 (SI) - Body ground
    Ignition switch ON
    (Wheels turned slowly)
    Voltage generated intermittently

    Text in Illustration 
    *a
    Component with harness connected
    (Combination Meter Assembly)
    *b
    Wheels Turned

    HINT:
    The output voltage fluctuates up and down, similarly to the diagram, when the wheels are turned slowly.



NG
Go to step 7
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)  

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - VSC ACTUATOR WITH ACTUATOR BRACKET ASSEMBLY)
  1. Disconnect the combination meter assembly connector.

  1. Disconnect the VSC actuator with actuator bracket assembly connector.

  1. Measure the resistance according the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    J28-36 (SI) - A17-3 (SP1)
    Always
    Below 1 Ω
    J28-36 (SI) or A17-3 (SP1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE VSC ACTUATOR WITH ACTUATOR BRACKET ASSEMBLY (Click here)