Home › DRIVE LINE › DIFFERENTIAL › DIFFERENTIAL CARRIER OIL SEAL (for 3UR-FE, 3UR-FBE)

DIFFERENTIAL CARRIER OIL SEAL (for 3UR-FE, 3UR-FBE) > REPLACEMENT

for Preparation Click here



1. DRAIN DIFFERENTIAL OIL
  1. Stop the vehicle on a level place.

  1. for Front Differential:

    1. Using a 10 mm hexagon wrench, remove the filler plug and gasket.

    2. Using a 10 mm hexagon wrench, remove the drain plug and gasket, and drain the oil.

    3. Using a 10 mm hexagon wrench, install a new gasket and the drain plug.

      Torque:
      39 N*m{ 398 kgf*cm , 29 ft.*lbf }

  1. for Rear Differential:

    1. Remove the filler plug and gasket.

    2. Remove the drain plug and gasket, and drain the oil.

    3. Install a new gasket and the drain plug.

      Torque:
      49 N*m{ 500 kgf*cm , 36 ft.*lbf }



2. REMOVE PROPELLER SHAFT ASSEMBLY
  1. Remove the propeller shaft for 2WD (Click here).

  1. Remove the propeller shaft for 4WD (Click here).



3. REMOVE REAR DRIVE PINION NUT


    C089309E02
  1. Using SST and a hammer, loosen the staked part of the nut.

    SST
    09930-00010  



    B087842E02
  1. Using SST to hold the companion flange, remove the nut.

    SST
    09330-00021   (09330-00030)



4. REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY


    C186904E01
  1. Using SST, remove the companion flange.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09956-03050)
    09955-03050  



5. REMOVE REAR DIFFERENTIAL CARRIER OIL SEAL


    C161661E01
  1. Using SST, remove the oil seal.

    SST
    09308-10010  



6. INSTALL REAR DIFFERENTIAL CARRIER OIL SEAL


    C161433E01
  1. Using SST and a plastic-faced hammer, tap in a new oil seal until its surface is flush with the differential carrier end.

    SST
    09316-12010  
    09649-17010  

    Standard oil seal depth:
    -0.45 to 0.45 mm (-0.0177 to 0.0177 in.)

    HINT:
    Connect 2 SST with vinyl tape.

  1. Coat the lip of the oil seal with MP grease.



7. INSTALL REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY


    C186901E01
  1. Using SST, install the companion flange.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09956-03030)
    09955-03050  

  1. Coat the threads of a new nut with hypoid gear oil.



    C088916E04
  1. Using SST to hold the companion flange, install the nut.

    SST
    09330-00021   (09330-00030)

    Torque:
    304 N*m{ 3100 kgf*cm , 224 ft.*lbf }



8. STAKE REAR DRIVE PINION NUT


    C089310
  1. Using a chisel and hammer, stake the nut.



9. INSTALL PROPELLER SHAFT ASSEMBLY
  1. Install the propeller shaft for 2WD (Click here).

  1. Install the propeller shaft for 4WD (Click here).



10. ADD DIFFERENTIAL OIL


    D025304E27
  1. Add differential oil so that the oil level is between 0 to 5 mm (0 to 0.197 in.) from the bottom lip of the differential filler plug hole.

    NOTICE:
    1. Too much or too little oil will lead to differential problems.
    2. After changing the oil, drive the vehicle and then check the oil level again.

    Oil type:
    Item
    Oil type and viscosity
    Front differential
    Toyota Genuine Differential gear oil LT 75W-85 GL-5 or equivalent.
    Rear differential

    Front differential capacity:
    Specified Condition
    2.00 to 2.10 liters (2.12 to 2.21 US qts., 1.76 to 1.84 Imp. qts.)


    Rear differential capacity:

    Engine type
    Wheelbase type
    Cab type
    Drive type
    Specified Condition
    3UR-FE. 3UR-FBE
    3220 mm (10 ft. 6.8 in.)
    Regular
    2WD
    3.45 to 3.55 liters (3.65 to 3.75 US qts., 3.04 to 3.12 Imp. qts.)
    4WD
    3700 mm (12 ft. 1.7 in.)
    Regular
    2WD
    3.55 to 3.65 liters (3.76 to 3.85 US qts., 3.13 to 3.21 Imp. qts.)
    4WD
    Double
    2WD
    4WD
    CrewMax
    2WD
    3.70 to 3.80 liters (3.91 to 4.01 US qts., 3.26 to 3.34 Imp. qts.)
    4WD
    3.55 to 3.65 liters (3.76 to 3.85 US qts., 3.13 to 3.21 Imp. qts.)
    4180 mm (13 ft. 8.6 in.)
    Double
    2WD
    3.70 to 3.80 liters (3.91 to 4.01 US qts., 3.26 to 3.34 Imp. qts.)
    4WD
    1GR-FE and 1UR-FE
    3220 mm (10 ft. 6.8 in.)
    Regular
    2WD
    4.00 to 4.10 liters (4.23 to 4.33 US qts., 3.52 to 3.60 Imp. qts.)
    4WD
    3700 mm (12 ft. 1.7 in.)
    ALL
    2WD
    4.55 to 4.65 liters (4.81 to 4.91 US qts., 4.01 to 4.09 Imp. qts.)
    4WD
    4180 mm (13 ft. 8.6 in.)
    2WD
    4WD

  1. for Rear Differential:

    1. Install a new gasket and the filler plug.

      Torque:
      49 N*m{ 500 kgf*cm , 36 ft.*lbf }

  1. for Front Differential:

    1. Using a 10 mm hexagon wrench, install a new gasket and the filler plug.

      Torque:
      39 N*m{ 398 kgf*cm , 29 ft.*lbf }