Home › BODY ELECTRICAL › NAVIGATION › NAVIGATION SYSTEM (for DVD)

DTC    B1593    No Response from Stereo Component Amplifier

DTC    B15D3    Stereo Component Amplifier Disconnected

for Preparation Click here


DESCRIPTION

The navigation receiver assembly and stereo component amplifier are connected by the AVC-LAN communication line.
When an AVC-LAN communication error occurs between the navigation receiver assembly and stereo component amplifier, this DTC will be stored.

DTC Code
DTC Detection Condition
Trouble Area
B1593
Within the time-out period, there was no response from the stereo component amplifier to the following requests from the master unit:
  1. System inspection request
  2. System inspection result request
  3. Diagnostic memory request
  1. Stereo component amplifier power source circuit
  2. AVC-LAN circuit between navigation receiver assembly and stereo component amplifier
  3. Navigation receiver assembly
  4. Stereo component amplifier
B15D3*
When either condition below is met:
  1. Stereo component amplifier is/was not connected while the ignition switch is ON or ACC.
  2. Communication between the master unit and the stereo component amplifier is not possible when the engine is started.

HINT:
  1. *: Even if no fault is present, this DTC may be stored depending on the battery condition or engine start voltage.
  2. The navigation receiver assembly is the master unit.


WIRING DIAGRAM


E190581E02


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
  1. Check for optional components

    1. Check that optional components (including associated wiring) which generate radio waves are not installed.
      Result 
      Result
      Proceed to
      Optional components (including associated wiring) are installed.
      A
      Optional components (including associated wiring) are not installed.
      B

      HINT:
      1. Electrical noise from radio waves generated by optional components or the wiring for those components may affect AVC-LAN communication.
      2. This DTC may be stored when an AVC-LAN communication error occurs due to electrical noise.



B
Go to step 3
A


2.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
  1. Remove optional components (including associated wiring).

    NOTICE:
    Do not remove optional components or associated wiring without the permission of the customer.


NEXT


3.CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs and check if the same trouble occurs again.

    OK:
    No DTCs are output.



NG
Go to step 4
OK

USE SIMULATION METHOD TO CHECK (Click here)  

4.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - BATTERY AND BODY GROUND)


  1. Disconnect the K15, K16 and K17 stereo component amplifier assembly connectors.


    E191461E01

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    K17-6 (GND) - Body ground
    Always
    Below 1 Ω
    K17-7 (GND2) - Body ground

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    K16-1 (+B) - K17-6 (GND)
    Always
    11 to 14 V
    K16-5 (+B2) - K17-6 (GND)
    K15-12 (ACC) - K17-6 (GND)
    Ignition switch ACC



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER - STEREO COMPONENT AMPLIFIER)


    E191658E01
  1. Disconnect the K18 navigation receiver assembly connector.

  1. Disconnect the K15 stereo component amplifier connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    K18-5 (ATX+) - K15-8 (TX+)
    Always
    Below 1 Ω
    K18-15 (ATX-) - K15-7 (TX-)
    Always
    Below 1 Ω
    K18-5 (ATX+) - Body ground
    Always
    10 kΩ or higher
    K18-15 (ATX-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.REPLACE STEREO COMPONENT AMPLIFIER
  1. Replace the stereo component amplifier (Click here).

  1. Clear the DTCs (Click here).

  1. Recheck for DTCs and check if the same trouble occurs again.

    OK:
    No DTCs are output.



NG
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)
OK

END (STEREO COMPONENT AMPLIFIER IS FAULTY)