Home › BODY ELECTRICAL › AUDIO / VISUAL › AUDIO AND VISUAL SYSTEM

AUDIO AND VISUAL SYSTEM > Speaker Circuit (Built-in Amplifier)

for Preparation Click here


DESCRIPTION

The radio receiver assembly sends sound signals to the speaker.

WIRING DIAGRAM


E146451E04


INSPECTION PROCEDURE

1.CHECK SPEAKER
  1. Check the malfunctioning speakers.
    Result 
    Result
    Proceed to
    Malfunction in front speaker area
    A
    Malfunction in rear speaker area*
    B

    1. *: except Regular Cab



B
Go to step 7
A


2.CHECK FRONT SIDE SPEAKER
  1. Check the malfunctioning speakers.
    Result 
    Result
    Proceed to
    Front No. 2 speaker assembly
    A
    Front No. 1 speaker assembly
    B



B
Go to step 5
A


3.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY


    E146506E12
  1. Disconnect the K11*1 and/or K13*2 front No. 2 speaker assembly connector.

    1. *1: for RH
    2. *2: for LH

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH:
    Tester Connection
    Condition
    Specified Condition
    1 (+) - 3 (TWR+)
    Always
    Below 1 Ω
    2 (-) - 4 (TWR-)
    Always
    Below 1 Ω
    3 (TWR+) - 4 (TWR-)
    Always
    3.4 to 4.6 Ω
    for LH:
    Tester Connection
    Condition
    Specified Condition
    1 (+) - 3 (TWL+)
    Always
    Below 1 Ω
    2 (-) - 4 (TWL-)
    Always
    Below 1 Ω
    3 (TWL+) - 4 (TWL-)
    Always
    3.4 to 4.6 Ω

    Result 
    Result
    Proceed to
    OK
    A
    NG (for Regular Cab)
    B
    NG (for Double Cab)
    C
    NG (for CrewMax)
    D



B
REPLACE FRONT NO. 2 SPEAKER ASSEMBLY (Click here)

C
REPLACE FRONT NO. 2 SPEAKER ASSEMBLY (Click here)

D
REPLACE FRONT NO. 2 SPEAKER ASSEMBLY (Click here)
A


4.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - FRONT NO. 2 SPEAKER)


    E190905E03
  1. Disconnect the K1 radio receiver assembly connector.

  1. Disconnect the K11*1 and/or K13*2 front No. 2 speaker assembly connector.

    1. *1: for RH
    2. *2: for LH

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH:
    Tester Connection
    Condition
    Specified Condition
    K1-1 (FR+) - K11-3 (TWR+)
    Always
    Below 1 Ω
    K1-5 (FR-) - K11-4 (TWR-)
    Always
    Below 1 Ω
    K1-1 (FR+) - Body ground
    Always
    10 kΩ or higher
    K1-5 (FR-) - Body ground
    Always
    10 kΩ or higher
    for LH:
    Tester Connection
    Condition
    Specified Condition
    K1-2 (FL+) - K13-3 (TWL+)
    Always
    Below 1 Ω
    K1-6 (FL-) - K13-4 (TWL-)
    Always
    Below 1 Ω
    K1-2 (FL+) - Body ground
    Always
    10 kΩ or higher
    K1-6 (FL-) - Body ground
    Always
    10 kΩ or higher

    Result 
    Result
    Proceed to
    OK (for Column Shift Type)
    A
    OK (for Floor Shift Type)
    B
    NG
    C



B
REPLACE RADIO RECEIVER ASSEMBLY (Click here)

C
REPAIR OR REPLACE HARNESS OR CONNECTOR
A

REPLACE RADIO RECEIVER ASSEMBLY (Click here)  

5.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY


    E144966
  1. Disconnect the M8*1 and/or N10*2 front No. 1 speaker assembly connector.

    1. *1: for RH
    2. *2: for LH

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    3.2 to 4.8 Ω

    Result 
    Result
    Proceed to
    OK
    A
    NG (for Regular Cab)
    B
    NG (for Double Cab)
    C
    NG (for CrewMax)
    D



B
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)

C
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)

D
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)
A


6.CHECK HARNESS AND CONNECTOR (FRONT NO. 2 SPEAKER - FRONT NO. 1 SPEAKER)
  1. *1: for RH
  2. *2: for LH


    E108122E25
  1. Disconnect the K11*1 and/or K13*2 front No. 2 speaker assembly connector.

  1. Disconnect the M8*1 and/or N10*2 front No. 1 speaker assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH:
    Tester Connection
    Condition
    Specified Condition
    K11-1 (+) - M8-1
    Always
    Below 1 Ω
    K11-2 (-) - M8-2
    Always
    Below 1 Ω
    K11-1 (+) - Body ground
    Always
    10 kΩ or higher
    K11-2 (-) - Body ground
    Always
    10 kΩ or higher
    for LH:
    Tester Connection
    Condition
    Specified Condition
    K13-1 (+) - N10-1
    Always
    Below 1 Ω
    K13-2 (-) - N10-2
    Always
    Below 1 Ω
    K13-1 (+) - Body ground
    Always
    10 kΩ or higher
    K13-2 (-) - Body ground
    Always
    10 kΩ or higher

    Result 
    Result
    Proceed to
    OK (for Regular Cab)
    A
    OK (for Double Cab)
    B
    OK (for CrewMax)
    C
    NG
    D



B
REPLACE FRONT NO. 2 SPEAKER ASSEMBLY (Click here)

C
REPLACE FRONT NO. 2 SPEAKER ASSEMBLY (Click here)

D
REPAIR OR REPLACE HARNESS OR CONNECTOR
A

REPLACE FRONT NO. 2 SPEAKER ASSEMBLY (Click here)  

7.INSPECT REAR NO. 1 SPEAKER ASSEMBLY


    E144966
  1. Disconnect the O1*1 and O7*2 rear No. 1 speaker assembly connectors.

    1. *1: for RH
    2. *2: for LH

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    3.2 to 4.8 Ω

    Result 
    Result
    Proceed to
    OK
    A
    OK (for Double Cab)
    B
    OK (for CrewMax)
    C



B
REPLACE REAR NO. 1 SPEAKER ASSEMBLY (Click here)

C
REPLACE REAR NO. 1 SPEAKER ASSEMBLY (Click here)
A


8.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - REAR NO. 1 SPEAKER)
  1. *1: for RH
  2. *2: for LH


    E146563E03
  1. Disconnect the K2 radio receiver assembly connector.

  1. Disconnect the O1*1 and/or O7*2 rear No. 1 speaker assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH:
    Tester Connection
    Condition
    Specified Condition
    K2-1 (RR+) - O1-1
    Always
    Below 1 Ω
    K2-3 (RR-) - O1-2
    Always
    Below 1 Ω
    K2-1 (RR+) - Body ground
    Always
    10 kΩ or higher
    K2-3 (RR-) - Body ground
    Always
    10 kΩ or higher
    for LH:
    Tester Connection
    Condition
    Specified Condition
    K2-2 (RL+) - O7-1
    Always
    Below 1 Ω
    K2-6 (RL-) - O7-2
    Always
    Below 1 Ω
    K2-2 (RL+) - Body ground
    Always
    10 kΩ or higher
    K2-6 (RL-) - Body ground
    Always
    10 kΩ or higher

    Result 
    Result
    Proceed to
    OK (for Column Shift Type)
    A
    OK (for Floor Shift Type)
    B
    NG
    C



B
REPLACE RADIO RECEIVER ASSEMBLY (Click here)

C
REPAIR OR REPLACE HARNESS OR CONNECTOR
A

REPLACE RADIO RECEIVER ASSEMBLY (Click here)