Home › BODY ELECTRICAL › AUDIO / VISUAL › AUDIO AND VISUAL SYSTEM

DTC    74-40    Short in Speaker Circuit

for Preparation Click here


DESCRIPTION


DTC Code
DTC Detection Condition
Trouble Area
74-40
A short is detected in the speaker output circuit.
  1. Harness or connector
  2. Speaker
  3. Stereo component amplifier assembly

WIRING DIAGRAM


E146449E02


E160611E03


INSPECTION PROCEDURE

HINT:
After the inspection is completed, clear the DTCs.

1.CHECK FOR DTC
  1. Disconnect the K16 and K17 stereo component amplifier assembly connectors.

  1. Clear the DTC.

  1. Check if DTC 74-40 is output.

    OK:
    DTC 74-40 is not output.



NG
REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY (Click here)
OK


2.CHECK FOR DTC
  1. Reconnect the K16 stereo component amplifier assembly connector.

  1. Check if DTC 74-40 is output.

    OK:
    DTC 74-40 is not output.



NG
Go to step 7
OK


3.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - SPEAKER)


  1. Disconnect the K17 stereo component amplifier assembly connector.


    E191107E01

  1. Disconnect the M8*1 and/or N10*2 front No. 1 speaker assembly connector.

    1. *1: for RH
    2. *2: for LH

  1. Disconnect the P14 w/ box No. 1 speaker assembly connector.

  1. Disconnect the K14 front No. 4 speaker assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    K17-10 (CTR-) - K14-2
    Always
    Below 1 Ω
    K17-4 (CTR+) - K14-1
    Always
    Below 1 Ω
    K17-12 (WF1-) - P14-2
    Always
    Below 1 Ω
    K17-5 (WF1+) - P14-1
    Always
    Below 1 Ω
    K17-3 (WFR-) - M8-2
    Always
    Below 1 Ω
    K17-9 (WFR+) - M8-1
    Always
    Below 1 Ω
    K17-1 (WFL-) - N10-2
    Always
    Below 1 Ω
    K17-2 (WFL+) - N10-1
    Always
    Below 1 Ω
    K17-10 (CTR-) - Body ground
    Always
    10 kΩ or higher
    K17-4 (CTR+) - Body ground
    Always
    10 kΩ or higher
    K17-12 (WF1-) - Body ground
    Always
    10 kΩ or higher
    K17-5 (WF1+) - Body ground
    Always
    10 kΩ or higher
    K17-3 (WFR-) - Body ground
    Always
    10 kΩ or higher
    K17-9 (WFR+) - Body ground
    Always
    10 kΩ or higher
    K17-1 (WFL-) - Body ground
    Always
    10 kΩ or higher
    K17-2 (WFL+) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT FRONT NO. 4 SPEAKER ASSEMBLY


    E146506
  1. Disconnect the K14 front No. 4 speaker assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    1.5 to 2.1 Ω

    Result 
    Result
    Proceed to
    OK
    A
    NG (for Double Cab)
    B
    NG (for CrewMax)
    C



B
REPLACE FRONT NO. 4 SPEAKER ASSEMBLY

C
REPLACE FRONT NO. 4 SPEAKER ASSEMBLY
A


5.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY RH


    E144966
  1. Disconnect the M8 front No. 1 speaker assembly RH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    1.8 to 2.6 Ω

    Result 
    Result
    Proceed to
    OK
    A
    NG (for Double Cab)
    B
    NG (for CrewMax)
    C



B
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY RH (Click here)

C
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY RH (Click here)
A


6.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY LH


    E144966
  1. Disconnect the N10 front No. 1 speaker assembly LH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    1.8 to 2.6 Ω

    Result 
    Result
    Proceed to
    OK (for Double Cab)
    A
    OK (for CrewMax)
    B
    NG (for Double Cab)
    C
    NG (for CrewMax)
    D



B
REPLACE W/ BOX NO. 1 SPEAKER ASSEMBLY (Click here)

C
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY LH (Click here)

D
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY LH (Click here)
A

REPLACE W/ BOX NO. 1 SPEAKER ASSEMBLY (Click here)  

7.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - SPEAKER)
  1. *1: for RH
  2. *2: for LH
  3. *3: for Double Cab
  4. *4: for CrewMax


  1. Disconnect the K16 stereo component amplifier assembly connector.


    E191108E01

  1. Disconnect the K10*1 and/or K12*2 front No. 2 speaker assembly connector.

  1. Disconnect the O1*1 and/or O7*2 rear No. 1 speaker assembly*3 connector.

  1. Disconnect the O2*1 and/or O8*2 rear No. 2 speaker assembly*4 connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH:
    Tester Connection
    Condition
    Specified Condition
    K16-2 (FR+) - K10-3 (TWR+)
    Always
    Below 1 Ω
    K16-6 (FR-) - K10-4 (TWR-)
    Always
    Below 1 Ω
    K16-10 (RR+) - O1-1*1
    Always
    Below 1 Ω
    K16-4 (RR-) - O1-2*1
    Always
    Below 1 Ω
    K16-10 (RR+) - O2-3 (+TW)*2
    Always
    Below 1 Ω
    K16-4 (RR-) - O2-1 (-TW)*2
    Always
    Below 1 Ω
    K16-2 (FR+) - Body ground
    Always
    10 kΩ or higher
    K16-6 (FR-) - Body ground
    Always
    10 kΩ or higher
    K16-10 (RR+) - Body ground
    Always
    10 kΩ or higher
    K16-4 (RR-) - Body ground
    Always
    10 kΩ or higher
    for LH:
    Tester Connection
    Condition
    Specified Condition
    K16-8 (FL+) - K12-3 (TWL+)
    Always
    Below 1 Ω
    K16-7 (FL-) - K12-4 (TWL-)
    Always
    Below 1 Ω
    K16-3 (RL+) - O7-1*1
    Always
    Below 1 Ω
    K16-9 (RL-) - O7-2*1
    Always
    Below 1 Ω
    K16-3 (RL+) - O8-3 (+TW)*2
    Always
    Below 1 Ω
    K16-9 (RL-) - O8-1 (+TW)*2
    Always
    Below 1 Ω
    K16-8 (FL+) - Body ground
    Always
    10 kΩ or higher
    K16-7 (FL-) - Body ground
    Always
    10 kΩ or higher
    K16-3 (RL+) - Body ground
    Always
    10 kΩ or higher
    K16-9 (RL-) - Body ground
    Always
    10 kΩ or higher

    1. *1: for Double Cab
    2. *2: for CrewMax



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.CHECK HARNESS AND CONNECTOR (FRONT NO. 2 SPEAKER - FRONT NO. 3 SPEAKER)
  1. *1: for RH
  2. *2: for LH


    E190038E02
  1. Disconnect the K10*1 and/or K12*2 front No. 2 speaker assembly connector.

  1. Disconnect the M1*1 and/or N1*2 front No. 3 speaker assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH:
    Tester Connection
    Condition
    Specified Condition
    K10-2 (-) - M1-1
    Always
    Below 1 Ω
    K10-1 (+) - M1-3
    Always
    Below 1 Ω
    K10-2 (-) - Body ground
    Always
    10 kΩ or higher
    K10-1 (+) - Body ground
    Always
    10 kΩ or higher
    for LH:
    Tester Connection
    Condition
    Specified Condition
    K12-2 (-) - N1-1
    Always
    Below 1 Ω
    K12-1 (+) - N1-3
    Always
    Below 1 Ω
    K12-2 (-) - Body ground
    Always
    10 kΩ or higher
    K12-1 (+) - Body ground
    Always
    10 kΩ or higher

    Result 
    Result
    Proceed to
    OK (for CrewMax)
    A
    OK (for Double Cab)
    B
    NG
    C



B
Go to step 10

C
REPAIR OR REPLACE HARNESS OR CONNECTOR
A


9.CHECK HARNESS AND CONNECTOR (REAR NO. 1 SPEAKER - REAR NO. 2 SPEAKER)
  1. *1: for RH
  2. *2: for LH


    E190037E02
  1. Disconnect the O1*1 and/or O7*2 rear No. 1 speaker assembly connector.

  1. Disconnect the O2*1 and/or O8*2 rear No. 2 speaker assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH:
    Tester Connection
    Condition
    Specified Condition
    O1-2 - O2-2 (-)
    Always
    Below 1 Ω
    O1-1 - O2-4 (+)
    Always
    Below 1 Ω
    O1-2 - Body ground
    Always
    10 kΩ or higher
    O1-1 - Body ground
    Always
    10 kΩ or higher
    for LH:
    Tester Connection
    Condition
    Specified Condition
    O7-2 - O8-2 (-)
    Always
    Below 1 Ω
    O7-1 - O8-4 (+)
    Always
    Below 1 Ω
    O7-2 - Body ground
    Always
    10 kΩ or higher
    O7-1 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10.INSPECT FRONT NO. 3 SPEAKER ASSEMBLY RH


    E160614
  1. Disconnect the M1 front No. 3 speaker assembly RH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 3
    Always
    3.0 to 4.2 Ω

    Result 
    Result
    Proceed to
    OK
    A
    NG (for Double Cab)
    B
    NG (for CrewMax)
    C



B
REPLACE FRONT NO. 3 SPEAKER ASSEMBLY RH

C
REPLACE FRONT NO. 3 SPEAKER ASSEMBLY RH
A


11.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY RH


    E144969E29
  1. Disconnect the K10 front No. 2 speaker assembly RH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 (TWR+) - 4 (TWR-)
    Always
    1.5 to 2.5 Ω
    2 (-) - 4 (TWR-)
    Always
    Below 1 Ω
    1 (+) - 3 (TWR+)

    Result 
    Result
    Proceed to
    OK
    A
    NG (for Double Cab)
    B
    NG (for CrewMax)
    C



B
REPLACE FRONT NO. 2 SPEAKER ASSEMBLY RH

C
REPLACE FRONT NO. 2 SPEAKER ASSEMBLY RH
A


12.INSPECT FRONT NO. 3 SPEAKER ASSEMBLY LH


    E160614
  1. Disconnect the N1 front No. 3 speaker assembly LH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 3
    Always
    3.0 to 4.2 Ω

    Result 
    Result
    Proceed to
    OK
    A
    NG (for Double Cab)
    B
    NG (for CrewMax)
    C



B
REPLACE FRONT NO. 3 SPEAKER ASSEMBLY LH

C
REPLACE FRONT NO. 3 SPEAKER ASSEMBLY LH
A


13.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY LH


    E144969E30
  1. Disconnect the K12 front No. 2 speaker assembly LH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 (TWL+) - 4 (TWL-)
    Always
    1.5 to 2.5 Ω
    2 (-) - 4 (TWL-)
    Always
    Below 1 Ω
    1 (+) - 3 (TWL+)

    Result 
    Result
    Proceed to
    OK
    A
    NG (for Double Cab)
    B
    NG (for CrewMax)
    C



B
REPLACE FRONT NO. 2 SPEAKER ASSEMBLY LH

C
REPLACE FRONT NO. 2 SPEAKER ASSEMBLY LH
A


14.INSPECT REAR NO. 1 SPEAKER ASSEMBLY RH


    E144966
  1. Disconnect the O1 rear No. 1 speaker assembly RH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    1.8 to 2.6 Ω

    Result 
    Result
    Proceed to
    OK (for CrewMax)
    A
    OK (for Double Cab)
    B
    NG (for Double Cab)
    C
    NG (for CrewMax)
    D



B
Go to step 16

C
REPLACE REAR NO. 1 SPEAKER ASSEMBLY RH (Click here)

D
REPLACE REAR NO. 1 SPEAKER ASSEMBLY RH (Click here)
A


Go to step 16

15.INSPECT REAR NO. 2 SPEAKER ASSEMBLY RH


    E160614E23
  1. Disconnect the O2 rear No. 2 speaker assembly RH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (-TW) - 3 (+TW)
    Always
    3.0 to 4.2 Ω
    1 (-TW) - 2 (-)
    Always
    Below 1 Ω
    3 (+TW) - 4 (+)



NG
REPLACE REAR NO. 2 SPEAKER ASSEMBLY RH
OK


16.INSPECT REAR NO. 1 SPEAKER ASSEMBLY LH
E144966
  1. Disconnect the O7 rear No. 1 speaker assembly LH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    1.8 to 2.6 Ω

    Result 
    Result
    Proceed to
    OK (for CrewMax)
    A
    OK (for Double Cab)
    B
    NG (for Double Cab)
    C
    NG (for CrewMax)
    D



B
REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY (Click here)

C
REPLACE REAR NO. 1 SPEAKER ASSEMBLY LH (Click here)

D
REPLACE REAR NO. 1 SPEAKER ASSEMBLY LH (Click here)
A


17.INSPECT REAR NO. 2 SPEAKER ASSEMBLY LH


    E160614E24
  1. Disconnect the O8 rear No. 2 speaker assembly LH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (-TW) - 3 (+TW)
    Always
    3.0 to 4.2 Ω
    1 (-TW) - 2 (-)
    Always
    Below 1 Ω
    3 (+TW) - 4 (+)



NG
REPLACE REAR NO. 2 SPEAKER ASSEMBLY LH
OK

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY (Click here)