Home › STEERING › POWER STEERING › STEERING GEAR

STEERING GEAR > INSTALLATION

for Preparation Click here



1. INSTALL POWER STEERING GEAR ASSEMBLY


C212320E01
  1. Install the power steering gear with the 2 bolts and 2 nuts.

    Torque:
    120 N*m{ 1224 kgf*cm , 89 ft.*lbf }



2. INSTALL PRESSURE FEED TUBE ASSEMBLY


    C181258
  1. Temporarily connect the pressure feed tube to the power steering gear.



    C181255
  1. Install the pressure feed tube clamp with the 2 bolts.

    Torque:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }



    C181256E01
  1. Using a union nut wrench, tighten the pressure feed tube (pressure feed tube side).

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

    NOTICE:
    Use the formula calculate special torque values for situations for situations where a union nut wrench is combined with a torque wrench (Click here).



    C181257E01
  1. Using a union nut wrench, tighten the pressure feed tube (return tube side).

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

    NOTICE:
    Use the formula calculate special torque values for situations for situations where a union nut wrench is combined with a torque wrench (Click here).



3. CONNECT TIE ROD END SUB-ASSEMBLY LH
  1. Connect the tie rod end LH to the steering knuckle with the nut.

    Torque:
    69 N*m{ 704 kgf*cm , 51 ft.*lbf }

  1. Install a new cotter pin.

    HINT:
    Further tighten the nut up to 60° if the holes for the cotter pin are not aligned.



4. CONNECT TIE ROD END SUB-ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.



5. CONNECT NO. 2 STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY


C155151E01
  1. Align the matchmarks on the No. 2 steering intermediate shaft and power steering gear.

  1. Install the bolt.

    Torque:
    35 N*m{ 360 kgf*cm , 26 ft.*lbf }



6. INSTALL ENGINE ASSEMBLY
  1. for 1GR-FE:
    Install the engine assembly (Click here).

  1. for 3UR-FBE:
    Install the engine assembly (Click here).

  1. for 1UR-FE:
    Install the engine assembly (Click here).

  1. for 3UR-FE:
    Install the engine assembly (Click here).



7. INSTALL FRONT WHEEL

Torque:
for Aluminum Wheel:
131 N*m{ 1336 kgf*cm , 97 ft.*lbf }
for Steel Wheel:
209 N*m{ 2131 kgf*cm , 154 ft.*lbf }



8. BLEED POWER STEERING FLUID (for 1GR-FE)
  1. Check the fluid level.

  1. Jack up the front of the vehicle and support it with stands.

  1. Turn the steering wheel.

    1. With the engine stopped, turn the wheel slowly from lock to lock several times.

  1. Lower the vehicle.

  1. Start the engine.

  1. Run the engine at idle for a few minutes.

  1. Turn the steering wheel.

    1. With the engine idling, turn the wheel left or right to the full lock position and keep it there for 2 to 3 seconds, then turn the wheel to the opposite full lock position and keep it there for 2 to 3 seconds.(*1)

    2. Repeat (*1) several times.

  1. Stop the engine.



    C124274E02
  1. Check for foaming or emulsification.
    If the system has to be bled twice because of foaming or emulsification, check for fluid leaks in the system.

  1. Check the fluid level.



9. BLEED POWER STEERING FLUID (for 1UR-FE)
  1. Check the fluid level.

  1. Jack up the front of the vehicle and support it with stands.

  1. Turn the steering wheel.

    1. With the engine stopped, turn the wheel slowly from lock to lock several times.

  1. Lower the vehicle.

  1. Start the engine.

  1. Run the engine at idle for a few minutes.

  1. Turn the steering wheel.

    1. With the engine idling, turn the wheel left or right to the full lock position and keep it there for 2 to 3 seconds, and then turn the wheel to the opposite full lock position and keep it there for 2 to 3 seconds.*1

    2. Repeat *1 several times.

  1. Stop the engine.



    C124274E02
  1. Check for foaming or emulsification.
    If the system has to be bled twice because of foaming or emulsification, check for fluid leaks in the system.

  1. Check the fluid level.



10. BLEED POWER STEERING FLUID (for 3UR-FE, 3UR-FBE)
  1. Check the fluid level.

  1. Jack up the front of the vehicle and support it with stands.

  1. Turn the steering wheel.

    1. With the engine stopped, turn the wheel slowly from lock to lock several times.

  1. Lower the vehicle.

  1. Start the engine.

  1. Run the engine at idle for a few minutes.

  1. Turn the steering wheel.

    1. With the engine idling, turn the wheel left or right to the full lock position and keep it there for 2 to 3 seconds, then turn the wheel to the opposite full lock position and keep it there for 2 to 3 seconds.(*1)

    2. Repeat (*1) several times.

  1. Stop the engine.



    C124274E02
  1. Check for foaming or emulsification.
    If the system has to be bled twice because of foaming or emulsification, check for fluid leaks in the system.

  1. Check the fluid level.



11. CHECK POWER STEERING FLUID LEVEL (for 1GR-FE)


    C158723E01
  1. Keep the vehicle horizontal.

  1. With the engine stopped, check the fluid level in the reservoir.
    If necessary, add fluid.

    Fluid:
    ATF DEXRON II or III

    HINT:
    If the fluid is hot, check that the fluid level is within the HOT range. If the fluid is cold, check that the fluid level is within the COLD range.

  1. Start the engine and run it at idle.

  1. Turn the steering wheel from lock to lock several times to raise fluid temperature.

    Fluid temperature:
    80°C (176°F)



    C124274E02
  1. Check for foaming or emulsification.
    If foaming or emulsification is identified, bleed the power steering system.



    C124276E03
  1. With the engine idling, measure the fluid level in the reservoir.

  1. Stop the engine.

  1. Wait a few minutes and remeasure the fluid level in the reservoir.

    Maximum fluid level rise:
    5.0 mm (0.197 in.)

    If the fluid level rise is more than the maximum, bleed the power steering system.

  1. Check the fluid level.



12. CHECK POWER STEERING FLUID LEVEL (for 1UR-FE)


    C158723E01
  1. Keep the vehicle horizontal.

  1. With the engine stopped, check the fluid level in the reservoir.
    If necessary, add fluid.

    Fluid:
    ATF DEXRON II or III

    HINT:
    If the fluid is hot, check that the fluid level is within the HOT range. If the fluid is cold, check that the fluid level is within the COLD range.

  1. Start the engine and run it at idle.

  1. Turn the steering wheel from lock to lock several times to raise the fluid temperature.

    Fluid temperature:
    80°C (176°F)



    C124274E02
  1. Check for foaming or emulsification.
    If foaming or emulsification is identified, bleed the power steering system.



    C124276E03
  1. With the engine idling, measure the fluid level in the reservoir.

  1. Stop the engine.

  1. Wait a few minutes and remeasure the fluid level in the reservoir.

    Maximum fluid level rise:
    5.0 mm (0.197 in.)

    If the fluid level rise is more than the maximum, bleed the power steering system.

  1. Check the fluid level.



13. CHECK POWER STEERING FLUID LEVEL (for 3UR-FE, 3UR-FBE)


    C158723E01
  1. Keep the vehicle horizontal.

  1. With the engine stopped, check the fluid level in the reservoir.
    If necessary, add fluid.

    Fluid:
    ATF DEXRON II or III

    HINT:
    If the fluid is hot, check that the fluid level is within the HOT range. If the fluid is cold, check that the fluid level is within the COLD range.

  1. Start the engine and run it at idle.

  1. Turn the steering wheel from lock to lock several times to raise the fluid temperature.

    Fluid temperature:
    80°C (176°F)



    C124274E02
  1. Check for foaming or emulsification.
    If foaming or emulsification is identified, bleed the power steering system.



    C124276E03
  1. With the engine idling, measure the fluid level in the reservoir.

  1. Stop the engine.

  1. Wait a few minutes and remeasure the fluid level in the reservoir.

    Maximum fluid level rise:
    5.0 mm (0.197 in.)

    If the fluid level rise is more than the maximum, bleed the power steering system.

  1. Check the fluid level.



14. INSPECT FOR POWER STEERING FLUID LEAK


15. PLACE FRONT WHEELS FACING STRAIGHT AHEAD

HINT:
Perform this procedure with the front of the vehicle jacked up.



16. ADJUST FRONT WHEEL ALIGNMENT
  1. Adjust the front wheel alignment (Click here).