Home › ENGINE ยท 1GR-FE › ENGINE MECHANICAL › ENGINE ASSEMBLY

ENGINE ASSEMBLY > INSTALLATION

for Preparation Click here


HINT:
Perform "Inspection After Repairs" after replacing the engine assembly (Click here).



1. INSTALL FRONT NO. 2 ENGINE MOUNTING BRACKET LH
  1. Install the front No. 2 engine mounting bracket LH with the bolt.

    Torque:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }



2. INSTALL ENGINE HANGER


    A229669E01
  1. Install 2 engine hangers with 4 bolts as shown in the illustration.

    Torque:
    33 N*m{ 337 kgf*cm , 24 ft.*lbf }

    Text in Illustration 
    *1
    No. 1 Engine Hanger
    *2
    No. 2 Engine Hanger

    HINT:
    No. 1 Engine Hanger
    12281-31110
    No. 2 Engine Hanger
    12282-31140
    Bolt
    91671-C0830



3. REMOVE ENGINE FROM ENGINE STAND
  1. Attach an engine sling device and hang the engine with a chain block.

  1. Lift the engine and remove it from the engine stand.

    NOTICE:
    1. With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine while it is suspended, as doing so is dangerous.
    2. Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.



4. INSTALL ENGINE ASSEMBLY
  1. Slowly lower the engine into the engine compartment.



    A237690
  1. Install the front engine mounting insulator LH with the nut and 2 bolts.

    Torque:
    for nut:
    72 N*m{ 734 kgf*cm , 53 ft.*lbf }
    for bolt:
    79 N*m{ 806 kgf*cm , 58 ft.*lbf }

    Text in Illustration 
    V100135
    Nut
    V100136
    Bolt

  1. Install the front engine mounting insulator RH with the nut and 2 bolts.

    Torque:
    for nut:
    72 N*m{ 734 kgf*cm , 53 ft.*lbf }
    for bolt:
    79 N*m{ 806 kgf*cm , 58 ft.*lbf }

  1. Remove the 2 engine hangers and 4 bolts.



5. INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY


    A224775E01
  1. Using SST, hold the crankshaft.

    SST
    09213-54015   (91651-60855)
    09330-00021  



    A227952E01
  1. Install the front spacer, drive plate and rear spacer to the crankshaft.
    Text in Illustration 
    *1
    Front Spacer
    *2
    Drive Plate and Ring Gear
    *3
    Rear Spacer
    V100135
    Automatic Transmission Side

    HINT:
    As the front spacer, the drive plate and ring gear and the rear spacer are not reversible, be sure to install them so that they are facing in the direction shown in the illustration.

  1. Clean the bolts and bolt holes.



    A192239E03
  1. Apply adhesive to 2 or 3 threads at the end of each of the 8 bolts.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

    Text in Illustration 
    *1
    Adhesive



    A224777E01
  1. Install and uniformly tighten the 8 bolts in several steps in the sequence shown in the illustration.

    Torque:
    83 N*m{ 846 kgf*cm , 61 ft.*lbf }

    NOTICE:
    Do not start the engine for at least 1 hour after installation.



6. INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR

HINT:
Only perform this procedure when replacement of the engine mounting insulator is necessary.

  1. Install the rear engine mounting insulator to the transmission with the 4 bolts.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



7. INSTALL AUTOMATIC TRANSMISSION ASSEMBLY
(Click here)


8. INSTALL PROPELLER SHAFT ASSEMBLY
(Click here)


9. CONNECT NO. 1 AND NO. 2 FUEL PIPES
  1. Connect the No. 1 and No. 2 fuel pipes (Click here).

  1. Install the No. 2 fuel pipe clamp to the fuel tube connector.



10. CONNECT HEATER WATER HOSE ASSEMBLY


    A239178E01
  1. Connect the heater water inlet and outlet hoses.
    Text in Illustration 
    *a
    Top

    HINT:
    The direction of the hose clamp is indicated in the illustration.

  1. Attach the wire harness clamp.



11. CONNECT COOLER COMPRESSOR ASSEMBLY
  1. Install the cooler compressor with the 2 stud bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



    A238276E01
  1. Install the 2 bolts and 2 nuts.

    Torque:
    25 N*m{ 250 kgf*cm , 18 ft.*lbf }

    HINT:
    Tighten the bolts and nuts in the order shown in the illustration to install the cooler compressor.

  1. Connect the cooler compressor connector.



12. CONNECT ENGINE WIRE
  1. Attach the 2 claws and connect the 2 connectors to connect the engine room junction block connector to the engine room junction block.

  1. Attach the claw and install the bolt to connect the engine wire harness.

    Torque:
    17 N*m{ 173 kgf*cm , 13 ft.*lbf }

  1. Attach the clamp and connect the air pump connector.

  1. Install the ground cable with the 2 bolts.

    Torque:
    8.4 N*m{ 86 kgf*cm , 74 in.*lbf }

  1. Attach the clamp and connect the ECM connector (Click here).

  1. Attach the 2 clamps and connect the 7 connectors to connect the junction block connector to the junction block.

  1. Install the junction block cover.

  1. Attach the 2 wire harness clamps.

  1. Connect the 2 air injection control driver connectors.



13. INSTALL DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT
  1. Turn the crankshaft to gain access to the 6 bolts and install each bolt while holding the crankshaft pulley setting bolt with a wrench.

    Torque:
    48 N*m{ 489 kgf*cm , 35 ft.*lbf }

    NOTICE:
    First install the black colored bolt and then install the remaining 5 bolts.

  1. Install the flywheel housing side cover.



14. INSTALL STARTER ASSEMBLY (for 1.6 kW Type)
  1. Install the starter with the 2 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

  1. Connect the starter wire with the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Install the terminal cap.

  1. Connect the starter connector.

  1. Connect the ground wire with the bolt.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }



15. INSTALL STARTER ASSEMBLY (for 1.4 kW Type)
  1. Install the starter with the 2 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

  1. Connect the starter wire with nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Connect the starter connector.

  1. Connect the ground wire with the bolt.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }



16. INSTALL STARTER COVER (for 1.4 kW Type)
  1. Install the starter cover with the 3 bolts.

    Torque:
    12 N*m{ 117 kgf*cm , 8 ft.*lbf }



17. INSTALL GENERATOR ASSEMBLY
  1. Install the generator bracket to the generator with the bolt.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Install the generator with the 2 bolts.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }

  1. Install the generator bracket with the bolt.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Attach the wire harness clamp.

  1. Connect the wire harness bracket with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the generator connector to the generator.

  1. Install the generator wire with the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Close the terminal cap.



18. INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY LH


    A222094E01
  1. Install a new gasket to the cylinder head.
    Text in Illustration 
    *1
    Protrusion
    V100135
    Front

    NOTICE:
    Be careful of the installation direction.



    A237700E01
  1. Temporarily install the manifold with the new nut labeled 1.

  1. Install the remaining 5 new nuts and tighten the nuts in the sequence shown in the illustration.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



19. INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR
  1. Install the heat insulator with the 3 bolts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }



20. INSTALL NO. 2 AIR TUBE


    A239089E01
  1. Install 2 new gaskets to the No. 2 air tube as shown in the illustration.
    Text in Illustration 
    *1
    New Gasket
    *2
    No. 2 Air Tube

  1. Install the No. 2 air tube with the 2 bolts and 2 nuts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



21. INSTALL MANIFOLD STAY
  1. Install the manifold stay with the 3 bolts.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



22. INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY RH


    A222095E01
  1. Install a new gasket to the cylinder head.
    Text in Illustration 
    *1
    Protrusion
    V100135
    Front

    NOTICE:
    Be careful of the installation direction.



    A237697E01
  1. Temporarily install the manifold with the new nut labeled 1.

  1. Install the remaining 5 new nuts and tighten the nuts in the sequence shown in the illustration.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



23. INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR
  1. Install the heat insulator with the 3 bolts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }



24. INSTALL AIR TUBE


    A239082E01
  1. Install 2 new gaskets to the air tube as shown in the illustration.
    Text in Illustration 
    *1
    New Gasket
    *2
    Air Tube

  1. Install the air tube with the 2 bolts and 2 nuts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



25. INSTALL NO. 2 MANIFOLD STAY
  1. Install the manifold stay with the 3 bolts.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

  1. Connect the wire harness connector.



26. INSTALL FRONT EXHAUST PIPE ASSEMBLY
  1. Install a new gasket and the exhaust pipe to the exhaust manifold RH with 3 new nuts.

    Torque:
    54 N*m{ 551 kgf*cm , 40 ft.*lbf }

  1. Install a new gasket and the exhaust pipe to the center exhaust pipe with the 2 bolts.

    Torque:
    48 N*m{ 489 kgf*cm , 35 ft.*lbf }

  1. Connect the air fuel ratio sensor connector.

  1. Connect the heated oxygen sensor connector and attach the 2 clamps.



27. INSTALL FRONT NO. 2 EXHAUST PIPE ASSEMBLY (except Regular Cab Standard Deck)
  1. Connect the front No. 2 exhaust pipe to the exhaust pipe support.

  1. Install a new gasket and the front No. 2 exhaust pipe to the exhaust manifold LH with 3 new nuts.

    Torque:
    54 N*m{ 551 kgf*cm , 40 ft.*lbf }

  1. Install a new gasket and the front No. 2 exhaust pipe to the center exhaust pipe with the 2 bolts.

    Torque:
    48 N*m{ 489 kgf*cm , 35 ft.*lbf }

  1. Connect the air fuel ratio sensor connector.

  1. Connect the heated oxygen sensor connector.



28. INSTALL FRONT NO. 2 EXHAUST PIPE ASSEMBLY (for Regular Cab Standard Deck)
  1. Install a new gasket and the front No. 2 exhaust pipe to the exhaust manifold LH with 3 new nuts.

    Torque:
    54 N*m{ 551 kgf*cm , 40 ft.*lbf }

  1. Connect the air fuel ratio sensor connector.

  1. Connect the heated oxygen sensor connector and attach the 2 clamps.



29. INSTALL FRONT NO. 3 EXHAUST PIPE SUB-ASSEMBLY (for Regular Cab Standard Deck)
  1. Install a new gasket to the front No. 2 exhaust pipe.

  1. Install a new gasket to the front No. 3 exhaust pipe.

  1. Connect the front No. 3 exhaust pipe to the exhaust pipe support.

  1. Install the front No. 3 exhaust pipe with the 4 bolts and 2 new nuts.

    Torque:
    48 N*m{ 489 kgf*cm , 35 ft.*lbf }



30. CONNECT VANE PUMP ASSEMBLY
  1. Connect the vane pump with the 2 bolts.

    Torque:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }

  1. Attach the wire harness clamp.

  1. Connect the connector.



31. INSTALL FAN AND GENERATOR V BELT


    A225650E01
  1. Set the V belt onto every part.
    Text in Illustration 
    *1
    Vane Pump
    *2
    Water Pump
    *3
    No. 2 Idler
    *4
    Generator
    *5
    Cooler Compressor
    *6
    No. 1 Idler
    *7
    Crankshaft
    *8
    V-ribbed Belt Tensioner

  1. While turning the belt tensioner counterclockwise, remove the pin.

    NOTICE:
    Make sure that the V belt is properly installed to each pulley.



    B000540E06
  1. Check that the belt fits properly in the ribbed grooves.
    Text in Illustration 
    *1
    CORRECT
    *2
    INCORRECT

    HINT:
    Make sure to check by hand that the belt has not slipped out of the grooves on the bottom of the pulley.



32. INSTALL INTAKE AIR SURGE TANK
  1. Install a new gasket to the intake air surge tank.



    A221465E04
  1. Install the intake air surge tank with the 4 bolts and 2 nuts in the order shown in the illustration.

    Torque:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }

    Text in Illustration 
    *1
    Nut

  1. Install the throttle body bracket with the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Install the No. 1 surge tank stay with the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Attach the wire harness clamp.

  1. Install the No. 2 surge tank stay with the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



    A238097E01
  1. Connect the No. 1 ventilation hose.

  1. Connect the vacuum hose.

  1. Connect the No. 1 fuel feed hose.
    Text in Illustration 
    *a
    Front
    *b
    Matchmark
    *c
    Top

    HINT:
    Connect the hose so that the direction of the hose clamp is as indicated in the illustration.



    A225184E01
  1. Connect the throttle body connector.

  1. Connect the No. 4 water by-pass hose.

  1. Connect the No. 5 water by-pass hose.

    HINT:
    Connect the hose so that the direction of the hose clamp is as indicated in the illustration.

  1. Connect the 2 heater hose clamps.
    Text in Illustration 
    *a
    Front
    *b
    Matchmark
    *c
    RH



33. INSTALL AIR TUBE ASSEMBLY


    A238098E01
  1. for Bank 1 Side:
    Align the paint mark with the projection and connect the air tube assembly to the emission control valve set.
    Text in Illustration 
    *1
    Projection
    *2
    Paint Mark
    *a
    Upper
    *b
    RH Side

    HINT:
    Make sure the direction of the hose clamp is as shown in the illustration.



    A238099E01
  1. for Bank 2 Side:
    Align the paint mark with the projection and connect the air tube assembly to the No. 2 emission control valve set.
    Text in Illustration 
    *1
    Paint Mark
    *2
    Projection
    *a
    Upper
    *b
    LH Side

    HINT:
    Make sure the direction of the hose clamp is as shown in the illustration.

  1. Install the 3 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Install the wire harness clamp bracket with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Attach the 3 wire harness clamps to the intake air surge tank and bracket.

  1. Connect the purge VSV connector.



    A238101E01
  1. Connect the air injection system hose to the air tube assembly shown in the illustration.
    Text in Illustration 
    *1
    Paint Mark
    *2
    Projection
    *a
    Upper
    *b
    LH Side

    HINT:
    1. Make sure the paint mark of the air injection system hose is facing upward.
    2. Make sure the direction of the hose clamp is as shown in the illustration.



34. INSTALL RADIATOR ASSEMBLY


    A151752
  1. Set the radiator bracket hooks to the radiator support holes.

  1. Install the radiator with the 4 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

  1. Connect the radiator side deflector LH with the 3 clips.

  1. Connect the radiator side deflector RH with the 3 clips.



35. INSTALL FAN SHROUD
  1. Install the fan pulley to the water pump.

  1. Place the shroud together with the coupling fan between the radiator and engine.

    NOTICE:
    Be careful not to damage the radiator core.



    A229548E02
  1. Align the paint marks on the heads of the water pump stud bolts with the paint marks of the same color on the outer edge of the fluid coupling flange and install the fluid coupling to the water pump.
    Text in Illustration 
    *1
    Paint Mark

  1. Temporarily install the fluid coupling fan to the water pump with the 4 nuts. Tighten the nuts as much as possible by hand.



    A151756
  1. Attach the claws of the shroud to the radiator as shown in the illustration.

  1. Install the shroud with the 2 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }

  1. Connect the reservoir hose to the radiator tank upper.

  1. Install the fan and generator V-belt .

  1. Tighten the 4 nuts of the fluid coupling fan.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



36. INSTALL RADIATOR HOSE OUTLET


    A238133E01
  1. Connect the radiator hose outlet to the water inlet housing shown in the illustration.
    Text in Illustration 
    *a
    Upper
    *b
    Front



    A238134E01
  1. Install the radiator hose outlet to the radiator shown in the illustration.
    Text in Illustration 
    *a
    Upper
    *b
    RH



37. INSTALL RADIATOR HOSE INLET


    A238132E01
  1. Connect the radiator hose inlet as shown in the illustration.
    Text in Illustration 
    *a
    Upper
    *b
    LH
    *c
    Front



38. INSTALL AIR CLEANER CASE SUB-ASSEMBLY
  1. Install the air cleaner case with the 2 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Attach the wire harness clamp.

  1. Install the air cleaner filter element.



39. INSTALL AIR CLEANER CAP AND HOSE


    A239076E01
  1. Install the air cleaner cap and hose.
    Text in Illustration 
    *a
    Top
    *b
    Front
    *c
    RH Side
    *d
    Align cutout portion of hose with protrusion of throttle
    *e
    Paint Mark

    1. Attach the 4 hook clamps to install the air cleaner cap and hose.

    2. Tighten the clamp.

      Torque:
      4.0 N*m{ 41 kgf*cm , 35 in.*lbf }

    3. Attach the 4 clamps and connect the ventilation hose, vacuum hose and mass air flow meter connector.

      HINT:
      The direction of the hose clamp is indicated in the illustration.



40. ADD ENGINE COOLANT
  1. Add engine coolant.

    Standard capacity:
    10.7 liters (11.3 US qts, 9.4 Imp. qts)

    NOTICE:
    Do not substitute plain water for engine coolant.

    HINT:
    1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
    2. Press the No. 1 and No. 2 radiator hoses several times by hand, and then check the coolant level. If the coolant level is low, add coolant.

  1. Slowly pour coolant into the radiator reservoir until it reaches the FULL line.

  1. Install the reservoir cap.

  1. Install the radiator cap.*1

  1. Start the engine and stop it immediately.*2

  1. Allow approximately 10 seconds to pass. Then remove the radiator cap and check the coolant level. If the coolant level has decreased, add coolant.*3

  1. Repeat steps *1, *2 and *3 until the coolant level does not decrease.

    HINT:
    Be sure to perform this step while the engine is cold, as air in the inlet radiator hose will flow into the radiator if the engine is warmed up and the thermostat opens.

  1. Install the radiator cap.*4

  1. Set the air conditioning as follows.*5
    Measurement Condition 
    Item
    Condition
    Fan speed
    Any setting except off
    Temperature
    Toward WARM
    Air conditioning switch
    Off

  1. Start the engine, warm it up until the thermostat opens, and then continue to run the engine for several minutes to circulate the coolant.*6

    CAUTION:
    1. Wear protective gloves. Hot areas on the parts may injure your hands.
    2. Be careful of the fan.
    3. Be careful as the engine, radiator and radiator hoses are hot and can cause burns.

    NOTICE:
    1. Immediately after starting the engine, if the radiator reservoir does not have any coolant, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the coolant is filled to the FULL line.
    2. Do not start the engine when there is no coolant in the radiator reservoir.
    3. Pay attention to the needle of the engine coolant temperature receiver gauge. Make sure that the needle does not show an abnormally high temperature.
    4. If there is not enough coolant, the engine may burn out or overheat.

    HINT:
    1. Press the inlet and outlet radiator hoses several times by hand to bleed air while warming up the engine.
    2. The thermostat opening timing can be confirmed by pressing the outlet radiator hose by hand and checking when the engine coolant starts to flow inside the hose.

  1. Stop the engine, wait until the engine coolant cools down to ambient temperature. Then remove the radiator cap and check the coolant level.*7

    CAUTION:
    Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. If the coolant level has decreased, add coolant and warm up the engine until the thermostat opens.*8

  1. If the coolant level has not decreased, check that the coolant level in the radiator reservoir is at the FULL line.
    If the coolant level is below the FULL line, repeat steps *4 through *8.
    If the coolant level is above the FULL line, drain coolant until the coolant level reaches the FULL line.



41. ADD ENGINE OIL
  1. Add fresh oil.

    Standard Oil Grade:
    Oil grade
    Oil Viscosity (SAE)
    ILSAC GF-5 multigrade engine oil
    0W-20

    Standard Oil Capacity:
    Item
    Specified Condition
    Drain and refill without oil filter change
    5.6 liters (5.9 US qts, 4.9 Imp. qts)
    Drain and refill with oil filter change
    6.1 liters (6.4 US qts, 5.4 Imp. qts)
    Dry fill
    7.0 liters (7.4 US qts, 6.2 Imp. qts)



42. INSTALL FRONT COWL TOP OUTER PANEL SUB-ASSEMBLY
  1. Install the front cowl top outer panel with the 7 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Connect the washer hose.



43. INSTALL FRONT WIPER MOTOR AND LINK ASSEMBLY
(Click here)


44. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



45. INSPECT FOR FUEL LEAK
  1. Make sure that there are no fuel leaks after performing maintenance on the fuel system.

    1. Connect the Techstream to the DLC3.

    2. Turn the ignition switch to ON and turn the Techstream on.

      NOTICE:
      Do not start the engine.

    3. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

    4. Check that there are no leaks from the fuel system.
      If there are fuel leaks, repair or replace parts as necessary.

    5. Turn the ignition switch off.

    6. Disconnect the Techstream from the DLC3.



46. INSPECT FOR ENGINE OIL LEAK
  1. Start the engine. Make sure that there are no oil leaks from the area that was worked on.



47. INSPECT FOR EXHAUST GAS LEAK
  1. If gas is leaking, tighten the areas necessary to stop the leak. Replace damaged parts as necessary.


48. CHECK ENGINE OIL LEVEL
  1. Warm up the engine, and then stop the engine and wait for 5 minutes.

  1. Check that the engine oil level is between the low level and full level marks on the dipstick.
    If low, check for leakage and add oil up to the full level mark.

    NOTICE:
    Do not fill engine oil above the full level mark.

    HINT:
    A certain amount of engine oil will be consumed while driving. In the following situations, oil consumption may increase, and engine oil may need to be refilled in between oil maintenance intervals.
    1. When the engine is new, for example directly after purchasing the vehicle or after replacing the engine.
    2. If low quality oil or oil of an inappropriate viscosity is used.
    3. When driving at high engine speed or with a heavy load, (when towing, or), when driving while accelerating or decelerating frequently.
    4. When leaving the idling for a long time, or when driving frequently through heavy traffic.
    When judging the amount of oil consumption, keep in mind that the oil may have become diluted, making it difficult to judge the true level accurately.



49. INSTALL FRONT FENDER APRON SEAL REAR RH
  1. Install the fender apron seal with the 5 clips.



50. INSTALL FRONT FENDER APRON SEAL REAR LH
  1. Install the fender apron seal with the 5 clips.



51. INSTALL FRONT FENDER APRON SEAL RH
  1. Install the front fender apron seal with the 6 clips.



52. INSTALL FRONT FENDER APRON SEAL LH
  1. Install the front fender apron seal with the 6 clips.



53. INSTALL NO. 1 ENGINE UNDER COVER


    A150108
  1. Hook the engine under cover to the vehicle body as shown in the illustration.

  1. Install the 3 screws and 5 bolts.

    Torque:
    for bolt:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }
    for screw:
    3.0 N*m{ 31 kgf*cm , 27 in.*lbf }



54. PERFORM RESET MEMORY
(Click here)


55. INSPECT IGNITION TIMING

NOTICE:
  1. Turn all electrical systems off.
  1. Perform the inspection when the cooling fan motor is turned off.

  1. Warm up the engine.

  1. When using the Techstream:

    1. Connect the Techstream to the DLC3.

    2. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / IGN Advance.

    3. Inspect the ignition timing during idling.

      Standard ignition timing:
      8 to 12° BTDC @ idle (transmission in neutral and A/C switch off)

    4. Check that the ignition timing advances immediately when the engine speed is increased.



    A206183E05
  1. When not using the Techstream:

    1. Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

      SST
      09843-18040  
      Text in Illustration 
      *a
      Front view of DLC3

      NOTICE:
      Be sure not to improperly connect the terminals. This may damage the engine.

    2. Connect the tester probe of a timing light to the wire of the ignition coil connector for the No. 1 cylinder.

      NOTICE:
      1. Use a timing light that detects primary signals.
      1. After the inspection, be sure to wrap the wire harness with tape.



    3. A076316E01
    4. Inspect the ignition timing during idling.

      Standard ignition timing:
      8 to 12° BTDC @ idle (transmission in neutral and A/C switch off)

    5. Remove SST from the DLC3.

    6. Inspect the ignition timing during idling.

      Standard ignition timing:
      7 to 24° BTDC @ idle (transmission in neutral and A/C switch off)

    7. Disconnect the timing light from the engine.



56. INSPECT ENGINE IDLE SPEED

NOTICE:
  1. Turn all the electrical systems off.
  1. Perform the inspection when the cooling fan motor is turned off.

  1. Warm up the engine.

  1. When using the Techstream:

    1. Connect the Techstream to the DLC3.

    2. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Engine Speed.

    3. Inspect the engine idle speed.

      Standard idle speed:
      650 to 750 rpm (transmission in neutral and A/C switch off)



    A206183E06
  1. When not using the Techstream:

    1. Connect SST to terminal 9 (TAC) of the DLC3.

      SST
      09843-18030  
      Text in Illustration 
      *a
      Front view of DLC3

    2. Race the engine at 2500 rpm for approximately 90 seconds.

    3. Inspect the engine idle speed.

      Standard idle speed:
      650 to 750 rpm (transmission in neutral and A/C switch off)



57. INSPECT CO/HC

HINT:
This check is to determine whether or not the idle CO/HC concentration complies with regulations.

  1. Start the engine.

  1. Run the engine at 2500 rpm for approximately 180 seconds.

  1. Insert the CO/HC meter testing probe at least 40 cm (1.31 ft) into the tailpipe during idling.

  1. Immediately check the CO/HC concentration during idling and/or at 2500 rpm.

    HINT:
    When carrying out the 2 tests (idling and 2500 rpm), the measurement orders are prescribed by the applicable local regulations.

  1. If the CO/HC concentration does not comply with regulations, perform troubleshooting in the order given below.

    1. Check the air fuel ratio sensor operation (Click here) and heated oxygen sensor operation (Click here).

    2. See the table below for possible causes, and then inspect and correct the corresponding causes if necessary.

      CO
      HC
      Symptom
      Causes
      Normal
      High
      Rough idling
      1. Faulty ignition:
        1. Incorrect timing
        2. Plugs are contaminated or shorted, or plug gaps are incorrect
      2. Incorrect valve clearance
      3. Leaky intake and exhaust valves
      4. Leaky cylinders
      Low
      High
      Rough idling
      (Fluctuating HC reading)
      1. Vacuum leaks:
        1. Ventilation hoses
        2. Intake manifold
        3. Throttle body
        4. Brake booster line
      2. Lean mixture causing misfire
      High
      High
      Rough idle
      (Black smoke from exhaust)
      1. Restricted air filter
      2. Plugged PCV valve
      3. Faulty SFI system:
        1. Faulty pressure regulator
        2. Defective engine coolant temperature sensor
        3. Faulty mass air flow meter
        4. Faulty ECM
        5. Faulty injectors
        6. Faulty throttle position sensor



58. INSTALL HOOD SUB-ASSEMBLY
  1. Install the hood with the 4 bolts and 2 clips.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }



59. ADJUST HOOD SUB-ASSEMBLY


    B166027
  1. Adjust the hood's position.

    1. Loosen the hood's 4 hinge bolts.

    2. Move the hood and adjust the clearance between the hood and front fender.

    3. Tighten the hood's 4 hinge bolts after the adjustment.

      Torque:
      13 N*m{ 133 kgf*cm , 10 ft.*lbf }



    4. B166028
    5. Adjust the cushion rubber so that the height of the hood and fender are aligned.

      HINT:
      Raise or lower the hood's front end by turning the cushion rubber.



  1. Adjust the hood lock.



      B166029
    1. Using a screwdriver, remove the hood lock nut cap as shown in the illustration.

      HINT:
      Tape the screwdriver tip before use.



    2. B166030
    3. Loosen the 2 bolts and hood lock nut.

    4. Adjust the hood lock position so that the striker can enter it smoothly.

    5. Tighten the bolts and nut after the adjustment.

      Torque:
      8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    6. Install a new cap.