Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B1690/15    Driver Side Door Side Airbag Sensor Malfunction

DTC    B1695/16    Passenger Side Door Side Airbag Sensor Malfunction

for Preparation Click here


DESCRIPTION

The door side airbag sensor LH or RH consists of the safing sensor, the diagnostic circuit, the lateral deceleration sensor, etc.
If the center airbag sensor receives signals from the lateral deceleration sensor, it determines whether the SRS should be activated.
DTC B1690/15 or B1695/16 is recorded when a malfunction is detected in the door side airbag sensor LH or RH circuit.

DTC Code
Detection Condition
Trouble Area
B1690/15
When one of the following conditions is met:
  1. Door side airbag sensor LH malfunction
  2. Center airbag sensor malfunction
  1. Door side airbag sensor LH
  2. Center airbag sensor assembly
B1695/16
When one of the following conditions is met:
  1. Door side airbag sensor RH malfunction
  2. Center airbag sensor malfunction
  1. Door side airbag sensor RH
  2. Center airbag sensor assembly

WIRING DIAGRAM


C158884E01


C158884E05


INSPECTION PROCEDURE

NOTICE:
  1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).
  2. When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (Click here).

1.CHECK FOR DTC
  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B1690 and B1695 are not output
    A
    DTC B1690 is output
    B
    DTC B1695 is output
    C

    HINT:
    Codes other than past DTC B1690 and B1695 maybe output at this time, but they are not related to this check.



A
USE SIMULATION METHOD TO CHECK (Click here)

B
Go to step 10
C


2.CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor, the side airbag sensor RH and door side airbag sensor RH.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


3.CHECK CONNECTORS
  1. Disconnect the connectors from the center airbag sensor and side airbag sensor RH.

  1. Check that the connectors (on the center airbag sensor side, the side airbag sensor RH side and door side airbag sensor RH side) are not damaged.

    OK:
    The connectors are not deformed or damaged.



NG
REPLACE NO. 2 FLOOR WIRE
OK


4.CHECK DOOR SIDE AIRBAG SENSOR RH CIRCUIT

C158839E01

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    M9-1 (BCR-) - Body ground
    Ignition switch ON
    Below 1 V
    M9-2 (BCR+) - Body ground

  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the connectors from the side airbag sensor RH and door side airbag sensor RH.

  1. Using a service wire, connect terminals 1 (BCR+) and 2 (BCR-) of connector B.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    M9-1 (BCR-) - M9-2 (BCR+)
    Always
    Below 1 Ω

  1. Disconnect the service wire from the connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    M9-1 (BCR-) - M9-2 (BCR+)
    Always
    1 MΩ or higher
    M9-1 (BCR-) - Body ground
    M9-2 (BCR+) - Body ground

    Result 
    Result
    Proceed to
    OK (for CrewMax)
    A
    NG
    B
    OK (for Double Cab)
    C



A
Go to step 8

B
Go to step 7
C


5.CHECK DOOR SIDE AIRBAG SENSOR RH
C172067E01
  1. Interchange the door side airbag sensor LH with RH and connect the connectors to them.

  1. Connect the negative (-) terminal to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B1690 is output (for Double Cab)
    A
    DTC B1690 and B1695 are not output
    B
    DTC B1695 is output
    C

  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Return the door side airbag sensor RH and LH to their original positions and connect the connectors to them.



A
REPLACE DOOR SIDE AIRBAG SENSOR RH (Click here)

B
USE SIMULATION METHOD TO CHECK (Click here)
C


6.CHECK SIDE AIRBAG SENSOR RH
C146230E03
  1. Interchange the side airbag sensor LH with RH and connect the connectors to them.

  1. Connect the negative (-) terminal to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B1690 and B1695 are not output
    A
    DTC B1690 is output (for Double Cab)
    B
    DTC B1695 is output (for Column Shift Type)
    C
    DTC B1695 is output (for Floor Shift Type)
    D

  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Return the side airbag sensor RH and LH to their original positions and connect the connectors to them.



A
USE SIMULATION METHOD TO CHECK (Click here)

B
REPLACE SIDE AIRBAG SENSOR RH (Click here)

C
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
D

REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)  

7.CHECK NO. 2 FLOOR WIRE

C158885E01

  1. Disconnect the No. 2 floor wire connector from the door wire RH.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    MQ1-1 (BCR-) - Body ground
    Ignition switch ON
    Below 1 V
    MQ1-2 (BCR+) - Body ground

  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Using a service wire, connect terminals 1 (BCR+) and 2 (BCR-) of connector B.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    MQ1-1 (BCR-) - MQ1-2 (BCR+)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    MQ1-1 (BCR-) - MQ1-2 (BCR+)
    Always
    1 MΩ or higher
    MQ1-1 (BCR-) - Body ground
    MQ1-2 (BCR+) - Body ground



NG
REPLACE NO. 2 FLOOR WIRE
OK

REPLACE DOOR WIRE RH 

8.CHECK DOOR SIDE AIRBAG SENSOR RH
C172067E01
  1. Interchange the door side airbag sensor LH with RH and connect the connectors to them.

  1. Connect the negative (-) terminal to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B1690 is output
    A
    DTC B1690 and B1695 are not output
    B
    DTC B1695 is output
    C

  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Return the door side airbag sensor RH and LH to their original positions and connect the connectors to them.



A
REPLACE DOOR SIDE AIRBAG SENSOR RH (Click here)

B
USE SIMULATION METHOD TO CHECK (Click here)
C


9.CHECK SIDE AIRBAG SENSOR RH
C146230E03
  1. Interchange the side airbag sensor LH with RH and connect the connectors to them.

  1. Connect the negative (-) terminal to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B1690 and B1695 are not output
    A
    DTC B1690 is output
    B
    DTC B1695 is output (for Column Shift Type)
    C
    DTC B1695 is output (for Floor Shift Type)
    D

  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Return the side airbag sensor RH and LH to their original positions and connect the connectors to them.



A
USE SIMULATION METHOD TO CHECK (Click here)

B
REPLACE SIDE AIRBAG SENSOR RH (Click here)

C
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
D

REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)  

10.CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor, the side airbag sensor LH and door side airbag sensor LH.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS CORRECTLY
OK


11.CHECK CONNECTORS
  1. Disconnect the connectors from the center airbag sensor and side airbag sensor LH.

  1. Check that the connectors (on the center airbag sensor side, the side airbag sensor LH side and door side airbag sensor LH side) are not damaged.

    OK:
    The connectors are not deformed or damaged.



NG
REPLACE FLOOR WIRE
OK


12.CHECK DOOR SIDE AIRBAG SENSOR LH CIRCUIT

C158839E02

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified condition
    N11-1 (BCL-) - Body ground
    Ignition switch ON
    Below 1 V
    N11-2 (BCL+) - Body ground

  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the connectors from the side airbag sensor LH and door side airbag sensor LH.

  1. Using a service wire, connect terminals 2 (BCL-) and 1 (BCL+) of connector B.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    N11-1 (BCL-) - N11-2 (BCL+)
    Always
    Below 1 Ω

  1. Disconnect the service wire from the connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    N11-1 (BCL-) - Body ground
    Always
    1 MΩ or higher
    N11-2 (BCL+) - Body ground

    Result 
    Result
    Proceed to
    OK (for CrewMax)
    A
    NG
    B
    OK (for Double Cab)
    C



A
Go to step 16

B
Go to step 15
C


13.CHECK DOOR SIDE AIRBAG SENSOR LH
C172067E02
  1. Interchange the door side airbag sensor RH with LH and connect the connectors to them.

  1. Connect the negative (-) terminal to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B1695 is output (for Double Cab)
    A
    DTC B1690 and B1695 are output
    B
    DTC B1690 is output
    C

  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Return the door side airbag sensor RH and LH to their original positions and connect the connectors to them.



A
REPLACE DOOR SIDE AIRBAG SENSOR LH (Click here)

B
USE SIMULATION METHOD TO CHECK (Click here)
C


14.CHECK SIDE AIRBAG SENSOR LH
C158841E02
  1. Interchange the side airbag sensor RH with LH and connect the connectors to them.

  1. Connect the negative (-) terminal to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B1690 and B1695 are not output
    A
    DTC B1695 is output (for Double Cab)
    B
    DTC B1690 is output (for Column Shift Type)
    C
    DTC B1690 is output (for Floor Shift Type)
    D

  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Return the side airbag sensor RH and LH to their original positions and connect the connectors to them.



A
USE SIMULATION METHOD TO CHECK (Click here)

B
REPLACE SIDE AIRBAG SENSOR LH (Click here)

C
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
D

REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)  

15.CHECK FLOOR WIRE

C158885E02

  1. Disconnect the floor wire connector from the door wire LH.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    NP1-1 (BCL-) - Body ground
    Ignition switch ON
    Below 1 V
    NP1-2 (BCL+) - Body ground

  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Using a service wire, connect terminals 1 (BCL+) and 2 (BCL-) of connector B.

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    NP1-1 (BCL-) - NP1-2 (BCL+)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    NP1-1 (BCL-) - NP1-2 (BCL+)
    Always
    1 MΩ or higher
    NP1-1 (BCL-) - Body ground
    NP1-2 (BCL+) - Body ground



NG
REPLACE FLOOR WIRE
OK

REPLACE DOOR WIRE LH 

16.CHECK DOOR SIDE AIRBAG SENSOR LH
C172067E02
  1. Interchange the door side airbag sensor RH with LH and connect the connectors to them.

  1. Connect the negative (-) terminal to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B1695 is output
    A
    DTC B1690 and B1695 are output
    B
    DTC B1690 is output
    C

  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Return the door side airbag sensor RH and LH to their original positions and connect the connectors to them.



A
REPLACE DOOR SIDE AIRBAG SENSOR LH (Click here)

B
REPLACE SIDE AIRBAG SENSOR LH (Click here)
C


17.CHECK SIDE AIRBAG SENSOR LH
C158841E02
  1. Interchange the side airbag sensor RH with LH and connect the connectors to them.

  1. Connect the negative (-) terminal to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B1690 and B1695 are not output
    A
    DTC B1695 is output
    B
    DTC B1690 is output (for Column Shift Type)
    C
    DTC B1690 is output (for Floor Shift Type)
    D

  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Return the side airbag sensor RH and LH to their original positions and connect the connectors to them.



A
USE SIMULATION METHOD TO CHECK (Click here)

B
REPLACE SIDE AIR BAG SENSOR LH (Click here)

C
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
D

REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)