DTC P0340 Camshaft Position Sensor Circuit Malfunction |
DTC P0342 Camshaft Position Sensor "A" Circuit Low Input (Bank 1 or Single Sensor) |
DTC P0343 Camshaft Position Sensor "A" Circuit High Input (Bank 1 or Single Sensor) |
DTC P0345 Camshaft Position Sensor "A" Circuit (Bank 2) |
DTC P0347 Camshaft Position Sensor "A" Circuit Low Input (Bank 2) |
DTC P0348 Camshaft Position Sensor "A" Circuit High Input (Bank 2) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0340 | Either condition is met:
|
|
| P0345 | There is no VVT sensor signal despite the crankshaft position sensor input being normal at an engine speed of 600 rpm or more (1 trip detection logic). |
|
| P0342 P0347 | Output voltage of the VVT sensor is below 0.3 V for 4 seconds (1 trip detection logic). |
|
| P0343 P0348 | Output voltage of the VVT sensor is higher than 4.7 V for 4 seconds (1 trip detection logic). |
|
![]() |
| Item | Content |
| Terminal | NE+ - NE- VV1+ - VV1- VV2+ - VV2- |
| Equipment Setting | 5 V/DIV. 20 msec./DIV. |
| Condition | Cranking or idling |
| Related DTCs | P0340: VVT sensor (Bank 1) verify pulse input P0340: Camshaft position/Crankshaft position misalignment (Bank 1) P0342: VVT sensor (Bank 1) range check (low voltage) P0343: VVT sensor (Bank 1) range check (high voltage) P0345: VVT sensor (Bank 2) verify pulse input P0347: VVT sensor (Bank 2) range check (low voltage) P0348: VVT sensor (Bank 2) range check (high voltage) |
| Required Sensors/Components (Main) | VVT sensor (for intake side) |
| Required Sensors/Components (Related) | Crankshaft position sensor |
| Frequency of Operation | Continuous |
| Duration | 4 seconds: P0340 (VVT sensor (Bank 1) verify pulse input), P0342, P0343, P0347 and P0348 5 seconds: Others |
| MIL Operation | 2 driving cycles: P0340 (VVT sensor (Bank 1) verify pulse input) Immediate: Others |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not present | None |
| Starter | ON |
| Minimum battery voltage while starter ON | Less than 11 V |
| Engine speed | 600 rpm or more |
| Starter | OFF |
| VVT system mis-alignment | Not detected |
| VVT sensor range check fail (P0342, P0343) | Not detected |
| VVT sensor voltage | 0.3 V or more, and 4.7 V or less |
| Starter | OFF |
| Ignition switch | ON |
| Time after ignition switch off to ON | 2 seconds or more |
| Battery voltage | 8 V or more |
| VVT sensor pulse input fail (P0340) | Not detected |
| Starter | OFF |
| Ignition switch | ON |
| Time after ignition switch off to ON | 2 seconds or more |
| Battery voltage | 8 V or more |
| VVT sensor pulse input fail (P0340, P0345) | Not detected |
| Engine speed | 600 rpm or more |
| Starter | OFF |
| VVT sensor voltage | 0.3 V or more, and 4.7 V or less |
| Battery voltage | 8 V or more |
| Ignition switch | ON |
| Time after ignition switch off to ON | 0.5 seconds or more |
| VVT sensor range check fail (P0342, P0343, P0347, P0348) | Not detected |
| VVT sensor signal | No signal |
| Either of the following conditions is met | 1 or 2 |
| 1. Camshaft position and crankshaft position alignment | Misaligned |
| 2. VVT sensor signal | No signal |
| VVT sensor voltage | Less than 0.3 V |
| VVT sensor voltage | More than 4.7 V |
| VVT sensor voltage | 0.3 to 4.7 V |
| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| 1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF VVT SENSOR (FOR INTAKE SIDE)) |
![]() |
Disconnect the VVT sensor (for intake side) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D79-3 (VC) - Body ground | Ignition switch ON | 4.5 to 5.0 V |
| D78-3 (VC) - Body ground | Ignition switch ON | 4.5 to 5.0 V |
| *A | for Bank 1 |
| *B | for Bank 2 |
| *a | Front view of wire harness connector (to VVT Sensor (for Intake Side)) |
|
| ||||
| OK | |
| 2.CHECK HARNESS AND CONNECTOR (VVT SENSOR (FOR INTAKE SIDE) - ECM) |
Disconnect the VVT sensor (for intake side) connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D79-1 (VVR+) - D74-90 (VV1+) | Always | Below 1 Ω |
| D79-2 (VVR-) - D74-89 (VV1-) | Always | Below 1 Ω |
| D78-1 (VVL+) - D74-87 (VV2+) | Always | Below 1 Ω |
| D78-2 (VVL-) - D74-88 (VV2-) | Always | Below 1 Ω |
| D79-1 (VVR+) or D74-90 (VV1+) - Body ground | Always | 10 kΩ or higher |
| D79-2 (VVR-) or D74-89 (VV1-) - Body ground | Always | 10 kΩ or higher |
| D78-1 (VVL+) or D74-87 (VV2+) - Body ground | Always | 10 kΩ or higher |
| D78-2 (VVL-) or D74-88 (VV2-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 3.CHECK SENSOR INSTALLATION (VVT SENSOR (FOR INTAKE SIDE)) |
![]() |
Check the VVT sensor (for intake side) installation.
|
| ||||
| OK | |
| 4.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY (TEETH OF PLATE) |
Check the teeth of the signal plate.
|
| ||||
| OK | |
| 5.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH) |
![]() |
Remove the cylinder head cover sub-assemblies RH and LH.
Turn the crankshaft pulley and align its groove with the "0" timing mark on the timing chain cover.
Check that the timing marks on the camshaft timing gears are aligned with the timing marks of the bearing cap as shown in the illustration.
| *1 | Timing Mark |
Reinstall the cylinder head cover RH and LH.
|
| ||||
| OK | |
| 6.REPLACE VVT SENSOR (FOR INTAKE SIDE) |
Replace the VVT sensor (for intake side) (Click here).
| NEXT | |
| 7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0340, P0342, P0343, P0345, P0347 OR P0348) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear the DTCs (Click here).
Refer to the confirmation driving pattern.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.
Read the DTCs.
| Result | Proceed to |
| No DTC is output | A |
| P0340, P0342, P0343, P0345, P0347 or P0348 is output | B |
|
| ||||
| A | ||
| ||