Home › ENGINE · 3UR-FBE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0300    Random / Multiple Cylinder Misfire Detected

DTC    P0301    Cylinder 1 Misfire Detected

DTC    P0302    Cylinder 2 Misfire Detected

DTC    P0303    Cylinder 3 Misfire Detected

DTC    P0304    Cylinder 4 Misfire Detected

DTC    P0305    Cylinder 5 Misfire Detected

DTC    P0306    Cylinder 6 Misfire Detected

DTC    P0307    Cylinder 7 Misfire Detected

DTC    P0308    Cylinder 8 Misfire Detected

for Preparation Click here


DESCRIPTION

A093767E03
When the engine misfires, high concentrations of hydrocarbons (HC) enter the exhaust gas. Extremely high HC concentration levels can cause increases in exhaust emission levels. High concentrations of HC can also cause increases in the Three-Way Catalytic Converter (TWC) temperature, which may cause damage to the TWC. To prevent these increases in emissions and to limit the possibility of thermal damage, the ECM monitors the misfire rate. When the temperature of the TWC reaches the point of thermal degradation, the MIL blinks. To monitor misfires, the ECM uses both the Camshaft Position (CMP) sensor and the Crankshaft Position (CKP) sensor. The CMP sensor is used to identify any misfiring cylinders and the CKP sensor is used to measure variations in the crankshaft rotation speed. Misfires are counted as when the crankshaft rotation speed variations exceed predetermined thresholds.
If the misfire rate exceeds the threshold level, the ECM illuminates the MIL and stores a DTC.

DTC No.
DTC Detection Condition
Trouble Area
P0300
Simultaneous misfiring of several cylinders occurs and one of the following conditions below is detected (2 trip detection logic):
  1. Misfire occurs that may damage the three-way catalytic converter (MIL blinks when detect immediately).
  2. Catalyst deterioration misfire occurs (MIL illuminates).
  1. Open or short in engine wire harness
  2. Connector connection
  3. Vacuum hose connections
  4. Ignition system
  5. Injector
  6. Fuel pressure
  7. Mass Air Flow (MAF) meter
  8. Engine Coolant Temperature (ECT) sensor
  9. Compression pressure
  10. Valve timing
  11. PCV valve and hose
  12. PCV hose connections
  13. Air induction system
  14. ECM
  15. Fuel pressure switching valve
  16. Fuel pressure regulator
  17. Fuel pressure regulator for high pressure
P0301
P0302
P0303
P0304
P0305
P0306
P0307
P0308
Misfiring of specific cylinder occurs and one of the following conditions below is detected (2 trip detection logic):
  1. Misfire occurs that may damage the three-way catalytic converter (MIL blinks when detect immediately).
  2. Catalyst deterioration misfire occurs (MIL illuminates).
When multiple DTCs for misfiring cylinders are set, but DTC P0300 is not stored, it indicates that misfires have been detected in different cylinders at different times. DTC P0300 is only stored when several misfiring cylinders are detected at the same time.

MONITOR DESCRIPTION

The ECM illuminates the MIL and stores a DTC when either one of the following conditions, which could cause emission deterioration, is detected (2 trip detection logic).
  1. Within the first 1000 crankshaft revolutions of the engine starting, an excessive misfiring rate (approximately 10 to 50 misfires per 1000 crankshaft revolutions) occurs once.
  2. An excessive misfiring rate (approximately 10 to 50 misfires per 1000 crankshaft revolutions) occurs a total of 4 times.
The ECM flashes the MIL (immediate detection logic) and sets a DTC (2 trip detection logic) when either one of the following conditions, which could cause the Three-Way Catalytic Converter (TWC) damage, is detected:
  1. At a high engine speed, a catalyst damage misfire, which monitored every 200 crankshaft revolutions, occurs once.
  2. At a normal engine speed, a catalyst damage misfire, which monitored every 200 crankshaft revolutions, occurs 3 times.

HINT:
If a catalyst damage misfire occurs, the ECM informs the driver by flashing the MIL.


MONITOR STRATEGY


Related DTCs
P0300: Multiple cylinder misfire
P0301: Cylinder 1 misfire
P0302: Cylinder 2 misfire
P0303: Cylinder 3 misfire
P0304: Cylinder 4 misfire
P0305: Cylinder 5 misfire
P0306: Cylinder 6 misfire
P0307: Cylinder 7 misfire
P0308: Cylinder 8 misfire
Required Sensors/Components (Main)
Crankshaft position sensor and Camshaft position sensor
Required Sensors/Components (Related)
Engine coolant temperature and intake air temperature sensors and Mass air flow meter
Frequency of Operation
Continuous
Duration
1000 crankshaft revolutions (soon after engine is started: 1 time, other 4 times) (Emissions-related misfire)
200 crankshaft revolutions (1 or 3 times) (Catalyst-damaging misfire)
MIL Operation
2 driving cycles: MIL illuminates when misfire detect
MIL flashes immediately: When catalyst damaged misfire occur
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Misfire: 
Monitor runs whenever following DTCs not stored
P0016, P0018 (VVT System - Misalignment)
P0017, P0019 (Exhaust VVT System - Misalignment)
P0102, P0103 (Mass Air Flow Sensor)
P0112, P0113 (Intake Air Temperature Sensor)
P0115, P0117, P0118 (Engine Coolant Temperature Sensor)
P0125 (Insufficient Coolant Temperature for Closed Loop Fuel Control)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle Position Sensor)
P0327, P0328, P0332, P0333, P032C, P032D, P033C, P033D (Knock Sensor)
P0335 (Crankshaft Position Sensor)
P1340 (Camshaft Position Sensor)
P0351 - P0358 (Igniter)
P0500 (Vehicle Speed Sensor)
P0705 (Shift Lever Position Switch)
Battery voltage
8 V or more
VVT system
Not operated by scan tool
Engine speed
400 to 5900 rpm
Either of following conditions (a) or (b) met
-
(a) ECT at engine start
More than -7°C (19°F)
(b) ECT
More than 20°C (68°F)
Fuel cut
OFF

Monitor period of emission-related-misfire: 
First 1000 revolutions after engine start, or Check Mode
Crankshaft 1000 revolutions
Except above
Crankshaft 1000 revolutions x 4

Monitor period of catalyst-damaged-misfire (MIL blinks): 
All of following conditions 1, 2, 3 and 4 met
Crankshaft 200 revolutions x 3
1. Driving cycles
1st
2. Check mode
OFF
3. Engine speed
Less than 2800 rpm
4. Engine load
Below 80%
Except above
Crankshaft 200 revolutions

TYPICAL MALFUNCTION THRESHOLDS


Monitor period of emission-related-misfire: 
Misfire rate
1.5% or more

Monitor period of catalyst-damaged-misfire (MIL blinks): 
Number of misfire per 200 revolutions
103 or more (varies with intake air amount and RPM)

MONITOR RESULT

Refer to CHECKING MONITOR STATUS (Click here).

WIRING DIAGRAM


A164725E02


A259910E01


A259911E01


CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON.
  3. Turn the Techstream on.
  4. Record the DTC(s) and freeze frame data.
  5. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  6. Using the Techstream, switch the ECM from normal mode to check mode (Click here).
  7. Read the misfire counts of each cylinder (Cylinder #1 Misfire Count to Cylinder #8 Misfire Count) with the engine idling.
  8. Drive the vehicle several times with the conditions, such as engine speed and engine load, shown in Misfire RPM and Misfire Load in the Data List.

    HINT:
    In order to store misfire DTCs, it is necessary to operate the vehicle for the period of time shown in the table below, using the Misfire RPM and Misfire Load in the Data List.

    Engine speed
    Duration
    Idling
    8.0 minutes or more
    1000
    4.5 minutes or more
    2000
    2.5 minutes or more
    3000
    1.5 minute or more

  9. Check whether misfires have occurred by checking DTCs and freeze frame data.

    HINT:
    Do not turn the ignition switch off until the stored DTCs and freeze frame data have been recorded. When the ECM returns to normal mode (default), the stored DTC, freeze frame data and other data will be erased.

  10. Record the DTC(s), freeze frame data and misfire counts.
  11. Turn the ignition switch off and wait for at least 15 seconds.
  12. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

INSPECTION PROCEDURE

HINT:
  1. If any DTCs other than misfire DTCs are output, troubleshoot those DTCs first.
  2. FFVs update the alcohol concentration learned value (Alcohol Density Estimate) when the vehicle is refueled. As idling stability may decrease when fuels having different properties are used, check with the customer about the fuels recently used in the vehicle.
  3. Make sure to compare the value of "Alcohol Density Estimate" in the freeze frame data with the current "Alcohol Density Estimate" value in the Data List.
  4. Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  5. If the misfire does not recur when the vehicle is brought to the workshop, reproduce the conditions stored in the freeze frame data.
  6. If the misfire still cannot be reproduced even though the conditions stored in the freeze frame data have been duplicated, one of the following factors is considered to be a possible cause of the problem:
    1. The fuel level is low.
    2. Improper fuel is used.
    3. The spark plugs are dirty.
  7. After finishing repairs, check that no misfires occur in each cylinder (No. 1, No. 2, No. 3, No. 4, No. 5, No. 6, No. 7 and No. 8 cylinder).
  8. Be sure to confirm that no misfiring cylinder DTCs are stored again by conducting the confirmation driving pattern, after the repairs.
  9. For 6 and 8 cylinder engines, the ECM intentionally does not store the specific misfiring cylinder DTCs at high engine speeds. If misfires only occur during high engine speed driving, only DTC P0300 is stored.
    In the event of DTC P0300 being present, perform the following operations:
    1. Clear the DTC (Click here).
    2. Start the engine and conduct the confirmation driving pattern.
    3. Read the misfiring rates of each cylinder or DTC(s) using the Techstream.
    4. Repair the cylinder(s) that has a high misfiring rate or is indicated by the DTC.
    5. After finishing repairs, conduct the confirmation driving pattern again, in order to verify that DTC P0300 is not stored.
  10. With the alcohol concentration learned value, Long FT and Short FT in the freeze frame data, it is possible to determine the actual A/F deviation when a malfunction occurs.
  11. When the Coolant Temp in the freeze frame data is less than 75°C (167°F), the misfires occurred only while warming up the engine.
  12. An extremely imbalanced drive wheel, which causes body vibration, may cause misfire DTCs detection.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO MISFIRE CODES)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.

    Result 
    Result
    Proceed to
    P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 and/or P0308 are output
    A
    P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 and/or P0308 and other DTCs are output
    B

HINT:
If any DTCs other than P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 and P0308 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.CHECK FREEZE FRAME DATA AND DATA LIST
  1. Make a note of the freeze frame data "Short FT #1 or #2" and "Long FT #1 or #2" which were recorded the moment DTCs were stored.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Short FT #1 or #2 and Long FT #1 or #2.

  1. Compare the air fuel ratio learned value (total of "Short FT #1" + "Long FT #1") in the freeze frame data with that in the Data List.

    Result 
    Short FT + Long FT
    Proceed to
    Freeze Frame Data
    Data List
    -35% or less
    -35% or less
    A
    Higher than -35%
    Higher than -35%
    -35% or less
    Higher than -35%
    B

    HINT:
    If only the freeze frame data indicates -35% or less, a misfire may have occurred in the past. Confirm the driving conditions with the customer (if the customer drove the vehicle in a way that can cause misfire, such as driving a short distance with a cold engine repeatedly). If the cause of misfire is due to driving conditions, clear the DTCs, check that there are no other malfunctions, and return the vehicle to the customer.
    Explain to the customer points to be careful about when driving a flexible fuel vehicle. (Refer to the owner's manual for details.)



B
END
A


3.CHECK PCV HOSE CONNECTIONS
  1. Check the PCV hose connections.

    OK:
    PCV hose is connected correctly and is not damaged.



NG
REPAIR OR REPLACE PCV HOSE (Click here)
OK


4.READ VALUE USING TECHSTREAM (MISFIRE RPM AND MISFIRE LOAD)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Misfire / Misfire RPM and Misfire Load.

  1. Read and note the Misfire RPM and Misfire Load values.

    HINT:
    The Misfire RPM and Misfire Load values indicate the vehicle conditions under which the misfire occurred.


NEXT


5.READ VALUE USING TECHSTREAM (CATALYST OT MF F/C)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Catalyst OT MF F/C.

  1. Read the value displayed on the Techstream.

    Result 
    Data List
    Display Item
    Proceed to
    Catalyst OT MF F/C
    Avail
    A
    Not Avl
    B



B
Go to step 7
A


6.PERFORM ACTIVE TEST USING TECHSTREAM (PROHIBIT THE CATALYST OT MISFIRE PREVENT F/C)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Clear DTCs (Click here).

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Prohibit the Catalyst OT Misfire prevent F/C.

  1. Perform the Active Test.

    NOTICE:
    When performing the Active Test, make sure the vehicle is stopped and either idling or being revved within 3000 rpm.


NEXT


7.READ VALUE USING TECHSTREAM (CYLINDER MISFIRE COUNT)
  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Misfire / Cylinder #1 Misfire Count, #2, #3, #4, #5, #6, #7 and #8.

  1. Allow the engine to idle.

  1. Read each value for Cylinder #1 Misfire Count to Cylinder #8 Misfire Count displayed on the Techstream. If no misfire counts occur in any cylinders, perform the following procedures:

    1. Move the shift lever to the D position.

    2. Check the Cylinder #1 Misfire Count to Cylinder #8 Misfire Count.

    3. If misfire counts are still not displayed, perform procedure "A" and "B" and then check the misfire counts again.

  1. Drive the vehicle with the Misfire RPM and Misfire Load noted in the "READ VALUE USING TECHSTREAM (MISFIRE RPM AND MISFIRE LOAD)" procedures above. (Procedure "A")

  1. Read the Cylinder #1 Misfire Count to Cylinder #8 Misfire Count or DTCs displayed on the Techstream. (Procedure "B")

    Result 
    Misfire Count
    Proceed to
    Most misfires occur in only 1 or 2 cylinders
    A
    3 cylinders or more have equal misfire counts
    B

    HINT:
    1. If it is difficult to reproduce misfires for each cylinder, check the Data List item called Misfire Margin. Try to find vehicle driving conditions that lower the Misfire Margin value. Values above 30% are considered normal.
    2. If the freeze frame data's record of the ECT is below 75°C (167°F), the misfire may be detected only when the engine is cold.
    3. If the freeze frame data's record of the Engine Run Time is below 120 seconds, the misfire may be detected immediately after the engine is started.



B
Go to step 18
A


8.INSPECT SPARK PLUG
  1. Inspect the spark plug of the misfiring cylinder .



NG
REPLACE SPARK PLUG (Click here)
OK


9.CHECK FOR SPARK (SPARK TEST)
  1. Perform a spark test .

    HINT:
    If the result of the spark test is normal, proceed to the next step.


NEXT


10.CHECK CYLINDER COMPRESSION PRESSURE
  1. Measure the cylinder compression pressure of the misfiring cylinder .



NG
CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION
OK


11.INSPECT ECM TERMINAL OF MISFIRING CYLINDER (#10, #20, #30, #40, #50, #60, #70 AND/OR #80 VOLTAGE)
A136305E22
  1. Disconnect the D74 ECM connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D74-86 (#10) - D74-43 (E01)
    Ignition switch ON
    11 to 14 V
    D74-109 (#20) - D74-43 (E01)
    Ignition switch ON
    11 to 14 V
    D74-85 (#30) - D74-43 (E01)
    Ignition switch ON
    11 to 14 V
    D74-108 (#40) - D74-43 (E01)
    Ignition switch ON
    11 to 14 V
    D74-84 (#50) - D74-43 (E01)
    Ignition switch ON
    11 to 14 V
    D74-107 (#60) - D74-43 (E01)
    Ignition switch ON
    11 to 14 V
    D74-83 (#70) - D74-43 (E01)
    Ignition switch ON
    11 to 14 V
    D74-106 (#80) - D74-43 (E01)
    Ignition switch ON
    11 to 14 V



NG
GO TO FUEL INJECTOR CIRCUIT (Click here)
OK


12.CHECK FUEL INJECTOR OF MISFIRING CYLINDER
  1. Check the injector injection [whether fuel volume is high or low, and whether injection pattern is poor] .



NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
OK


13.CHECK AIR INDUCTION SYSTEM
  1. Check the air induction system for vacuum leakage .

    OK:
    No leakage from air induction system.



NG
REPAIR OR REPLACE AIR INDUCTION SYSTEM (Click here)
OK


14.CHECK FUEL PRESSURE
  1. Check the fuel pressure .



NG
Go to step 33
OK


15.READ VALUE USING TECHSTREAM (COOLANT TEMP)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.

  1. Read the Coolant Temp twice, when the engine is both cold and warmed up.

    Standard:
    With cold engine: Same as ambient air temperature.
    With warm engine: Between 75°C and 100°C (167°F and 212°F).



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)
OK


16.READ VALUE USING TECHSTREAM (MAF)
  1. Connect the Techstream to the DLC3.

  1. Start the engine.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF and Coolant Temp.

  1. Allow the engine to idle until Coolant Temp reaches 75°C (167°F) or higher.

  1. Read MAF with the engine speed at 3000 rpm.

    Standard:
    Between 18.0 gm/sec. and 27.0 gm/sec. (shift lever: N; A/C: Off).



NG
Go to step 28
OK


17.CHECK VALVE TIMING

A166451E01

  1. Remove the cylinder head cover LH and RH.

  1. Turn the crankshaft pulley, and align its groove with the timing mark "0" of the timing chain cover.

  1. Check that the timing marks of the camshaft timing gears and camshaft timing exhaust gears are at the positions shown in the illustration.

    OK:
    Timing marks on camshaft timing gears are aligned as shown in the illustration.



OK
Go to step 28

NG
ADJUST VALVE TIMING (Click here)

18.CHECK AIR INDUCTION SYSTEM
  1. Check the air induction system for vacuum leakage .

    OK:
    No leakage from air induction system.



NG
REPAIR OR REPLACE AIR INDUCTION SYSTEM (Click here)
OK


19.CHECK FUEL PRESSURE
  1. Check the fuel pressure .



NG
Go to step 33
OK


20.READ VALUE USING TECHSTREAM (COOLANT TEMP)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.

  1. Read the Coolant Temp twice, when the engine is both cold and warmed up.

    Standard:
    With cold engine: Same as ambient air temperature.
    With warm engine: Between 75°C and 100°C (167°F and 212°F).



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)
OK


21.READ VALUE USING TECHSTREAM (MAF)
  1. Connect the Techstream to the DLC3.

  1. Start the engine.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF and Coolant Temp.

  1. Allow the engine to idle until Coolant Temp reaches 75°C (167°F) or higher.

  1. Read MAF with the engine speed at 3000 rpm.

    Standard:
    Between 18.0 gm/sec. and 27.0 gm/sec. (shift lever: N; A/C: Off).



NG
Go to step 28
OK


22.CHECK VALVE TIMING

A166451E01

  1. Remove the cylinder head cover LH and RH.

  1. Turn the crankshaft pulley, and align its groove with the timing mark "0" of the timing chain cover.

  1. Check that the timing marks of the camshaft timing gears and camshaft timing exhaust gears are at the positions shown in the illustration.

    OK:
    Timing marks on camshaft timing gears are aligned as shown in the illustration.



NG
ADJUST VALVE TIMING (Click here)
OK


23.INSPECT SPARK PLUG
  1. Inspect the spark plug of the misfiring cylinder .



NG
REPLACE SPARK PLUG (Click here)
OK


24.CHECK FOR SPARK (SPARK TEST)
  1. Perform a spark test .

    HINT:
    If the result of the spark test is normal, proceed to the next step.


NEXT


25.CHECK CYLINDER COMPRESSION PRESSURE
  1. Measure the cylinder compression pressure of the misfiring cylinder .



NG
CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION
OK


26.INSPECT ECM TERMINAL OF MISFIRING CYLINDER (#10, #20, #30, #40, #50, #60, #70 AND/OR #80 VOLTAGE)
A136305E22
  1. Disconnect the D74 ECM connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D74-86 (#10) - D74-43 (E01)
    Ignition switch ON
    11 to 14 V
    D74-109 (#20) - D74-43 (E01)
    Ignition switch ON
    11 to 14 V
    D74-85 (#30) - D74-43 (E01)
    Ignition switch ON
    11 to 14 V
    D74-108 (#40) - D74-43 (E01)
    Ignition switch ON
    11 to 14 V
    D74-84 (#50) - D74-43 (E01)
    Ignition switch ON
    11 to 14 V
    D74-107 (#60) - D74-43 (E01)
    Ignition switch ON
    11 to 14 V
    D74-83 (#70) - D74-43 (E01)
    Ignition switch ON
    11 to 14 V
    D74-106 (#80) - D74-43 (E01)
    Ignition switch ON
    11 to 14 V



NG
GO TO FUEL INJECTOR CIRCUIT (Click here)
OK


27.CHECK FUEL INJECTOR OF MISFIRING CYLINDER
  1. Check the injector injection [whether fuel volume is high or low, and whether injection pattern is poor] .



NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
OK


28.CHECK HARNESS AND CONNECTOR
  1. Check the connection and terminal contact pressure of the connectors and wire harnesses between the mass air flow meter and ECM (Click here).

    HINT:
    Repair any problems.


NEXT


29.CHECK WHETHER DTC OUTPUT RECURS (MISFIRE DTCS)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  1. Input the DTC: P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 or P0308.

  1. Check the DTC judgment result.

    Result 
    Display (DTC Output)
    Proceed to
    ABNORMAL
    (P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 or P0308 output)
    A
    NORMAL
    (No DTC output)
    B



B
END
A


30.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
  1. Disconnect the D7 MAF meter connector.

  1. Disconnect the D74 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:

    Tester Connection
    Condition
    Specified Condition
    D7-3 (VG) - D74-74 (VG)
    Always
    Below 1 Ω
    D7-2 (E2G) - D74-75 (E2G)
    Always
    Below 1 Ω
    D7-3 (VG) or D74-74 (VG) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


31.REPLACE MASS AIR FLOW METER
  1. Replace the mass air flow meter (Click here).

    HINT:
    If the results of the inspections performed in steps 16 and 21 indicated no problem, proceed to the next step without replacing the mass air flow meter.


NEXT


32.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  1. Input the DTC: P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 or P0308.

  1. Check the DTC judgment result.

    Result 
    Display (DTC Output)
    Proceed to
    NORMAL
    (No DTC output)
    A
    ABNORMAL
    (P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 or P0308 output)
    B



B
REPLACE ECM (Click here)
A

END 

33.CHECK FUEL LINE
  1. Check the fuel lines for leaks or blockage.



NG
REPAIR OR REPLACE FUEL LINE
OK

REPLACE FUEL PUMP