Home › CRUISE CONTROL SYSTEM › CRUISE CONTROL › CRUISE CONTROL SYSTEM

DTC    P0571    Brake Switch "A" Circuit

for Preparation Click here


DESCRIPTION

When the brake pedal is depressed, the stop light switch sends a signal to the ECM. When the ECM receives this signal, it cancels the cruise control. The fail-safe function operates to enable normal driving even if there is a malfunction in the stop light signal circuit. The cancellation condition occurs when voltage is applied to terminal STP. When the brake is applied, voltage is applied to terminal STP of the ECM through the STOP fuse and the stop light switch, and the ECM turns the cruise control off.

DTC Code
DTC Detection Condition
Trouble Area
P0571
When voltage of STP terminal and ST1- terminal of ECM are less than 1 V for 0.5 seconds. or more
  1. Stop light switch
  2. Stop light switch circuit
  3. ECM

WIRING DIAGRAM


E146082E03


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.READ VALUE USING TECHSTREAM (STOP LIGHT SWITCH)
  1. Using the Techstream, read the Data List (Click here).

    Cruise Control 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Stp Light SW M-CPU
    Stop light switch signal (Main CPU) / ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -

    OK:
    Normal conditions listed above are displayed.

    Result 
    Result
    Proceed to
    NG
    A
    OK (for 1GR-FE)
    B
    OK (for 1UR-FE)
    C
    OK (for 3UR-FE)
    D
    OK (for 3UR-FBE)
    E



B
REPLACE ECM (Click here)

C
REPLACE ECM (Click here)

D
REPLACE ECM (Click here)

E
REPLACE ECM (Click here)
A


2.INSPECT STOP LIGHT SWITCH
E146086E02
  1. Remove the stop light switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Pin pushed
    10 kΩ or higher
    Pin not pushed
    Below 1 Ω
    3 - 4
    Pin pushed
    Below 1 Ω
    Pin not pushed
    10 kΩ or higher



NG
REPLACE STOP LIGHT SWITCH (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (BATTERY - STOP LIGHT SWITCH)
E146087E01
  1. Disconnect the A4 stop light switch connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A4-2 - Body ground
    Always
    11 to 14 V
    A4-4 - Body ground
    Ignition switch ON



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH - ECM)
E146088E01
  1. Disconnect the A4 stop light switch connector.

  1. Disconnect the A24 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A4-1 - A24-36 (STP)
    Always
    Below 1 Ω
    A4-1 - Body ground
    Always
    10 kΩ or higher
    A4-3 - A24-35 (ST1-)
    Always
    Below 1 Ω
    A4-4 - Body ground
    Always
    10 kΩ or higher

    Result 
    Result
    Proceed to
    NG
    A
    OK (for 1GR-FE)
    B
    OK (for 1UR-FE)
    C
    OK (for 3UR-FE)
    D
    OK (for 3UR-FBE)
    E



B
REPLACE ECM (Click here)

C
REPLACE ECM (Click here)

D
REPLACE ECM (Click here)

E
REPLACE ECM (Click here)
A

REPAIR OR REPLACE HARNESS OR CONNECTOR