DTC P2444 Secondary Air Injection System Pump Stuck On Bank1 |
DTC P2445 Secondary Air Injection System Pump Stuck Off Bank1 |
| DTC No. | DTC Detection Condition | Trouble Area |
| P2444 | Secondary air pressure is higher than 3 kPa (23 mmHg) despite the ECM commanding the air pump to turn off (2 trip detection logic). |
|
| P2445 | Secondary air pressure is below 1 kPa (8 mmHg) despite the ECM commanding the air pump to turn on (2 trip detection logic). |
|
| Related DTCs | P2444: Air pump stuck ON P2445: Air pump stuck OFF |
| Required Sensors/Components (Main) | Pressure sensor |
| Required Sensors/Components (Related) | - |
| Frequency of Operation | Once per driving cycle |
| Duration | 7 seconds |
| MIL Operation | 2 driving cycles |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not stored | P0010, P0020 (VVT oil control valve) P0011, P0021 (VVT system - Advance) P0012, P0022 (VVT system - Retard) P0013, P0023 (Exhaust VVT oil control valve) P0014, P0024 (Exhaust VVT system - Advance) P0015, P0025 (Exhaust VVT system - Retard) P0016, P0018 (VVT system - Misalignment) P0017, P0019 (Exhaust VVT system - Misalignment) P0031, P0032, P0051, P0052, P101D, P103D (Air fuel ratio sensor heater) P0102, P0103 (Mass air flow meter) P0112, P0113 (Intake air temperature sensor) P0115, P0117, P0118 (Engine coolant temperature sensor) P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor) P0125 (Insufficient coolant temperature for closed loop fuel control) P0171, P0172, P0174, P0175 (Fuel system) P0301 - P0306 (Misfire) P0327, P0328, P0332, P0333 (Knock sensor) P0335 (Crankshaft position sensor) P0340, P0342, P0343, P0345, P0347, P0348 (VVT sensor) P0351 - P0356 (Igniter) P0365, P0367, P0368, P0390, P0392, P0393 (Exhaust VVT sensor) P0451, P0452, P0453 (EVAP system) P0500, P0722 (Vehicle speed sensor) P106B (Evap. emission control system pressure sensor - Air injection system pressure sensor correlation) P1613 (Secondary air injection driver) P014C, P014D, P014E, P014F, P015A, P015B, P015C, P015D, P2195, P2196, P2197, P2198, P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255, P2256 (Air fuel ratio sensor) P219A, P219B (Air-fuel ratio imbalance) P2431, P2432, P02433, P2436, P2437, P2438 (Secondary air injection system pressure sensor) |
| Battery voltage | 11 V or higher |
| Atmospheric pressure | 45 kPa (338 mmHg) or higher |
| Engine | Running |
| Pressure pattern check during secondary air injection ON*1 | Completed |
| Pressure pattern check during secondary air injection OFF*2 | Completed |
| Pressure change check: secondary air injection ON*3 | Completed |
| Pressure pulsation check: secondary air injection OFF*4 | Completed |
| Air injection control driver failure (open/short or out of range) | Not detected |
| Secondary air injection pressure sensor failure (open/short or out of range) | Not detected |
| *1: Pressure pattern check during secondary air injection ON | - |
| Time after secondary air injection starts operation | 4.8 seconds or more |
| Air pump | ON |
| Emission control valve | Open |
| Engine speed | 400 to 1650 rpm |
| Intake air amount | Less than 10 g/sec |
| Time after engine start | 5 seconds or more |
| *2: Pressure pattern check during secondary air injection OFF | - |
| Time after secondary air injection starts operation | 10 seconds or more |
| Air pump | OFF |
| Emission control valve | Closed |
| Engine speed | Less than 3750 rpm |
| Secondary air injection monitor during secondary air injection ON | Completed |
| Time after engine started | 5 seconds or more |
| *3: Pressure change check: secondary air injection ON | - |
| Secondary air injection | Operating |
| Air pump | ON |
| Emission control valve (bank 2) | Open |
| Emission control valve (bank 1) | Closed |
| Secondary air injection pressure sensor failure (open/short or out of range) | Not detected |
| Intake air amount | Less than 15 g/sec |
| *4: Pressure pulsation check: secondary air injection OFF | - |
| Pressure change check: secondary air injection ON | Completed |
| Pressure pulsation check: secondary air injection OFF | Not completed |
| Air pump | ON |
| Time after emission control valve (bank 2) closes | 0.3 seconds or more |
| Emission control valve (bank 1) | Open |
| Engine speed | Less than 3750 rpm |
| Either condition is met | (a) or (b) |
| (a) Condition 1 (secondary air injection OFF) | Met |
| (b) Condition 3 (secondary air injection OFF) | Met |
| Either condition is met | (a) or (b) |
| (a) Condition 2 (secondary air injection ON) | Met |
| (b) Condition 4 (secondary air injection ON) | Met |
| Both conditions are met during secondary air injection ON | - |
| Cumulative pressure pulsation | 15 kPa or higher |
| Secondary air injection pressure | 1 kPa or higher |
| Both conditions are met during secondary air injection ON | - |
| Cumulative pressure pulsation | 15 kPa or higher |
| Secondary air injection pressure | Below 1 kPa |
| Both conditions are met during secondary air injection ON | - |
| Cumulative pressure pulsation | Below 15 kPa |
| Secondary air injection pressure | 1 kPa or higher |
| Both conditions are met during secondary air injection ON | - |
| Cumulative pressure pulsation | Below 15 kPa |
| Secondary air injection pressure | Below 1 kPa |
| Both conditions are met during secondary air injection OFF | - |
| Cumulative pressure pulsation | 25 kPa or higher |
| Secondary air injection pressure | 3 kPa or higher |
| Both conditions are met during secondary air injection OFF | - |
| Cumulative pressure pulsation | 25 kPa or higher |
| Secondary air injection pressure | Below 3 kPa |
| Both conditions are met during secondary air injection OFF | - |
| Cumulative pressure pulsation | Below 25 kPa |
| Secondary air injection pressure | 3 kPa or higher |
| Both conditions are met during secondary air injection OFF | - |
| Cumulative pressure pulsation | Below 25 kPa |
| Secondary air injection pressure | Below 3 kPa |
| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| Air Pump | ON |
| Emission Control Valve | Open |
| Pressure | 1 kPa or higher |
| Pulsation Detection | Exhaust gas pulsation detected |
| Air Pump | OFF |
| Emission Control Valve | Open |
| Pressure | Below 3 kPa |
| Pulsation Detection | Exhaust gas pulsation detected |
| Air Pump | ON |
| Emission Control Valve | Closed |
| Pressure | 1 kPa or higher |
| Pulsation Detection | Exhaust gas pulsation not detected |
| Air Pump | OFF |
| Emission Control Valve | Closed |
| Pressure | Below 3 kPa |
| Pulsation Detection | Exhaust gas pulsation not detected |
| Air Pump | ON |
| Emission Control Valve | Open |
| Pressure | 1 kPa or higher |
| Pulsation Detection | Exhaust gas pulsation detected |
| Air Pump | OFF |
| Emission Control Valve | Open |
| Pressure | Below 3 kPa |
| Pulsation Detection | Exhaust gas pulsation detected |
| Air Pump | ON |
| Emission Control Valve | Closed |
| Pressure | 1 kPa or higher |
| Pulsation Detection | Exhaust gas pulsation not detected |
| Air Pump | OFF |
| Emission Control Valve | Closed |
| Pressure | Below 3 kPa |
| Pulsation Detection | Exhaust gas pulsation not detected |
| Detected Condition while Secondary Air Injection Operating: Air Pump ON, Emission Control Valve Open | Detected Condition while Secondary Air Injection not Operating: Air Pump OFF, Emission Control Valve Closed | ECM Determination | DTC Output |
| Case 1 | Case 8 | Normal | - |
| Case 1 | Case 6 | Emission control valve stuck open | P2440 or P2442 |
| Case 1 | Case 7 | Air pump stuck ON | P2444 |
| Case 2 | Case 8 | Air pump stuck OFF | P2445 |
| Case 3 | Case 8 | Emission control valve stuck closed | P2441 or P2443 |
| Case 1 | Case 5 | Emission control valve stuck open and air pump stuck ON | P2440 and/or P2442 and P2444 |
| Case 2 | Case 6 | Emission control valve stuck open and air pump stuck OFF | P2440 and/or P2442 and P2445 |
| Case 3 | Case 7 | Emission control valve stuck closed and air pump stuck ON | P2441 and/or P2443 and P2444 |
| Case 4 | Case 8 | Emission control valve stuck closed and air pump stuck OFF | P2441 and/or P2443 and P2445 |
| Techstream Operation | Air Pump | Emission Control Valve | Pressure*1 | Pulsation*2 |
| AIR PUMP: ON, ASV: OPEN | ON | OPEN | 1 kPa or higher | 15 kPa or higher |
| AIR PUMP: OFF, ASV: CLOSE | OFF | CLOSE | Below 3 kPa | Below 25 kPa |
| 1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2444 AND/OR P2445) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| P2444 and/or P2445 is output | A |
| P2444 and/or P2445 and P0418 are output | B |
| P2444 and/or P2445 and other DTCs (except P0418) are output | C |
|
| ||||
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST USING TECHSTREAM (SECONDARY AIR INJECTION SYSTEM OPERATION) |
Start the engine and warm it up.
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV1: OPEN, ASV2: OPEN and AIR PUMP: OFF, ASV1: CLOSE, ASV2: CLOSE.
Start the engine.
Perform the secondary air injection system forced operation while the engine is idling.
Check that the Data List values for the air pump (AIR PUMP), emission control valve (ASV) and pressure in the secondary air injection system passage (PRESSURE) displayed on the Techstream are as shown in the table below.
| Techstream Operation | Air Pump | Emission Control Valve | PRESSURE* |
| AIR PUMP: ON, ASV: OPEN | ON | ON | 1 kPa or higher [A] |
| AIR PUMP: OFF, ASV: CLOSE | OFF | OFF | Below 3 kPa [B] |
Turn the ignition switch off.
|
| ||||
| OK | |
| 3.CHECK WHETHER DTC OUTPUT RECURS (DTC P2444 AND/OR P2245) |
Start the engine and warm it up.
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear the DTCs (if stored) (Click here).
Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.
Start the engine after the Techstream initialization is finished.
Perform the System Check operation by pressing ENTER (Next).
Perform the following to confirm the secondary air injection system pending codes: Press the Exit button.
Check for pending DTCs.
Turn the ignition switch off.
| Result | Proceed to |
| P2444 and/or P2445 is output | A |
| No pending DTC is output | B |
|
| ||||
| A | |
| 4.INSPECT EMISSION CONTROL VALVE SET (PRESSURE SENSOR) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Air Pump Pressure (Absolute) and Air Pump2 Pressure (Absolute).
Check the pressure displayed on the Techstream.
| Result | Proceed to |
| OK | A |
| NG (for Bank 1) | B |
| NG (for Bank 2) | C |
|
| ||||
|
| ||||
| A | |
| 5.CHECK AIR INJECTION SYSTEM PIPE CONNECTIONS |

Check that all the pipes and hoses between the air pump and emission control valve are securely connected.
Inspect the pipes and hoses for blockages and damage.
|
| ||||
| OK | |
| 6.INSPECT AIR INJECTION CONTROL DRIVER ASSEMBLY (AIR INJECTION CONTROL DRIVER POWER SOURCE CIRCUIT) |
![]() |
Disconnect the air injection control driver assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D87-1 (E) - Body ground | Always | Below 1 Ω |
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D86-1 (BATT) - Body ground | Always | 11 to 14 V (near battery voltage) |
| D87-5 (+B) - Body ground | Ignition switch ON | 11 to 14 V (near battery voltage) |
| *a | Front view of wire harness connector (to Air Injection Control Driver Assembly) |
|
| ||||
| OK | |
| 7.CHECK HARNESS AND CONNECTOR (ECM - AIR INJECTION CONTROL DRIVER ASSEMBLY) |
Disconnect the ECM connector.
Disconnect the air injection control driver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D74-54 (AIRP) - D87-4 (SIP) | Always | Below 1 Ω |
| D74-54 (AIRP) or D87-4 (SIP) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 8.CHECK AIR PUMP ASSEMBLY |
Inspect the air pump assembly .
|
| ||||
|
| ||||
| 9.REPLACE AIR PUMP ASSEMBLY |
Replace the air pump assembly (Click here).
| NEXT | |
| 10.CHECK WHETHER DTC OUTPUT RECURS (DTC P2444 AND/OR P2445) |
Start the engine and warm it up.
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear the DTCs (if stored) (Click here).
Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.
Start the engine after the Techstream initialization is finished.
Perform the System Check operation by pressing ENTER (Next).
Perform the following to confirm the secondary air injection system pending codes: Press the Exit button.
Check for pending DTCs.
Turn the ignition switch off.
|
| ||||
| OK | ||
| ||
| 11.PERFORM ACTIVE TEST USING TECHSTREAM |
![]() |
Disconnect the air injection control driver assembly connector.
Connect terminals DI and SIV of the wire harness connector for the air injection control driver assembly.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV 1: OPEN, ASV 2: OPEN.
Start the engine.
Perform the secondary air injection system forced operation while the engine is idling.
Measure the voltage between the SIV and E terminals of the ECM connector when the secondary air injection system is ON and OFF.
Turn the ignition switch off.
| Tester Connection | Condition | Specified Condition |
| D87-3 (SIV) - D87-1 (E) | AIR PUMP: ON, ASV: OPEN | 0.5 to 2 V |
| D87-3 (SIV) - D87-1 (E) | AIR PUMP: OFF, ASV: CLOSE | 11 to 14 V |
| *1 | Air Injection Control Driver Assembly |
| *2 | ECM |
| *a | Front view of wire harness connector (to Air Injection Control Driver Assembly) |
![]() |
Connect terminals DI and SIP of the wire harness connector for the air injection control driver assembly.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV 1: OPEN, ASV 2: OPEN.
Start the engine.
Perform the secondary air injection system forced operation while the engine is idling.
Measure the voltage between the SIP and E terminals of the ECM connector when the secondary air injection system is ON and OFF.
Turn the ignition switch off.
| Tester Connection | Condition | Specified Condition |
| D87-4 (SIP) - D87-1 (E) | AIR PUMP: ON, ASV: OPEN | 0.5 to 2 V |
| D87-4 (SIP) - D87-1 (E) | AIR PUMP: OFF, ASV: CLOSE | 11 to 14 V |
| *1 | Air Injection Control Driver assembly |
| *2 | ECM |
| *a | Front view of wire harness connector (to Air Injection Control Driver Assembly) |
Reconnect the air injection control driver assembly connector.
|
| ||||
| OK | |
| 12.REPLACE AIR INJECTION CONTROL DRIVER ASSEMBLY |
Replace the air injection control driver assembly (Click here).
| NEXT | |
| 13.CHECK WHETHER DTC OUTPUT RECURS (DTC P2444 AND/OR P2445) |
Start the engine and warm it up.
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear the DTCs (if stored) (Click here).
Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.
Start the engine after the Techstream initialization is finished.
Perform the System Check operation by pressing ENTER (Next).
Perform the following to confirm the secondary air injection system pending codes: Press the Exit button.
Check for pending DTCs.
Turn the ignition switch off.
|
| ||||
| OK | ||
| ||