AUTOMATIC TRANSMISSION ASSEMBLY > INSTALLATION |
| 1. INSTALL TORQUE CONVERTER ASSEMBLY |
![]() |
Using a vernier caliper and straightedge, measure dimension A between the transmission fitting surface of the engine *1 and the converter fitting surface of the drive plate *2. (#)
![]() |
Aligning the matchmarks on the transmission case and torque converter, and then engage the splines of the input shaft and turbine runner.
| *a | Matchmark |
![]() |
Engage the splines of the stator shaft and stator while turning the torque converter.
| *a | Matchmark |
![]() |
Turn the torque converter and align the matchmarks on the torque converter and transmission case to engage the key of the oil pump drive gear into the slot on the torque converter.
| *a | Matchmark |
![]() |
Using a vernier caliper and a straightedge, measure dimension B shown in the illustration and check that B is greater than A measured in the first step.
| 2. INSTALL TRANSMISSION CONTROL CABLE BRACKET |
Install the bracket with the 2 bolts.
| 3. INSTALL WIRE HARNESS CLAMP BRACKET |
Install the front bracket LH with the bolt.
Install the rear bracket LH with the bolt.
Install the rear engine bracket with the bolt.
| 4. INSTALL PROPELLER SHAFT HEAT INSULATOR BRACKET SUB-ASSEMBLY |
Install the bracket with the bolt.
| 5. INSTALL TRANSMISSION OIL COOLER ASSEMBLY (w/o Trailer Towing System) |
![]() |
Coat 4 new O-rings with ATF.
Install the 4 O-rings, transmission oil cooler spacer and transmission oil cooler to the automatic transmission assembly with the 3 bolts.
| 6. INSTALL TRANSMISSION OIL COOLER ASSEMBLY (w/ Trailer Towing System) |
![]() |
Coat 4 new O-rings with ATF.
Install the 4 O-rings, transmission oil thermostat and transmission oil cooler to the automatic transmission assembly with the 3 bolts.
| 7. INSTALL AUTOMATIC TRANSMISSION ASSEMBLY |
![]() |
Apply clutch spline grease to the surface of the torque converter centerpiece that contacts the crankshaft.
| *1 | Torque Converter Centerpiece |
| *2 | Crankshaft |
![]() |
Confirm that the 2 knock pins are on the transaxle contact surface of the engine block before transaxle installation.
Install the transmission with the 10 bolts.
| 8. CONNECT NO. 2 WATER BY-PASS PIPE (w/o Towing Hitch) |
![]() |
Connect the 2 water by-pass hoses with the 2 clips and install the water by-pass pipe with the bolt.
| *a | Stopper |
| *b | RH Side |
| 9. CONNECT NO. 2 WATER BY-PASS PIPE (w/ Towing Hitch) |
![]() |
Connect the 2 oil cooler hoses to the transmission oil cooler.
| *a | Paint Mark |
![]() |
Connect the 2 water by-pass hoses with the 2 clips and install the water by-pass pipe with the bolt.
| *a | Stopper |
| *b | RH Side |
| 10. CONNECT BREATHER PLUG HOSE |
Connect the 3 breather plug hoses to the harness clamp bracket.
| 11. CONNECT WIRE HARNESS AND CONNECTOR |
![]() |
Connect the park/neutral start switch connector, 2 transmission wire connectors and 2 speed sensor connectors.
Connect the harness clamp with the bolt.
Connect the 3 connector clamps and 7 harness clamps.
Tilt up the automatic transmission.
Connect the ground cable with the bolt.
| 12. INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR |
Install the rear engine mounting insulator to the transmission with the 4 bolts.
| 13. INSTALL NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY |
Install the frame crossmember to the rear engine mounting insulator with the 4 bolts.
Install the frame crossmember with the 4 bolts, 4 washers and 4 nuts.
| 14. INSTALL DRIVE PLATE AND TORQUE CONVERTER CLUTCH SETTING BOLT |
Turn the crankshaft to gain access to the 6 bolts and install the bolts while holding the crankshaft pulley set bolt with a wrench.
| 15. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY |
![]() |
Connect the control cable with a new clip and the nut.
| 16. INSTALL STARTER ASSEMBLY |
| 17. INSTALL PROPELLER SHAFT ASSEMBLY |
| 18. INSTALL FRONT PROPELLER SHAFT ASSEMBLY |
| 19. INSTALL FRONT EXHAUST PIPE ASSEMBLY |
for Regular Cab Standard Deck:
(See page ).
except Regular Cab Standard Deck:
(See page ).
| 20. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 21. ADD AUTOMATIC TRANSMISSION FLUID |
| 22. ADD ENGINE COOLANT |
Add engine coolant.
| Item | Specified Condition |
| w/ Trailer Towing System | 13.0 liters (13.7 US qts, 11.4 Imp. qts) |
| w/o Trailer Towing System | 12.1 liters (12.8 US qts, 10.6 Imp. qts) |
![]() |
Slowly pour coolant into the radiator reservoir until it reaches the FULL line.
Install the reservoir cap.
Press the inlet and outlet radiator hoses several times by hand, and then check the coolant level. If the coolant level is low, add coolant.
Install the radiator cap.
Start the engine and warm it up until the thermostat opens.
Maintain the engine speed at 2000 to 2500 rpm.
Press the inlet and outlet radiator hoses several times by hand to bleed air.
Stop the engine, and wait until the engine coolant cools down to ambient temperature.
![]() |
Check that the coolant level is between the FULL and LOW lines.
If the coolant level is below the LOW line, repeat all of the procedures above.
If the coolant level is above the FULL line, drain coolant so that the coolant level is between the FULL and LOW lines.
| 23. INSPECT FOR ENGINE COOLANT LEAK |
![]() |
Fill the radiator with coolant and attach a radiator cap tester.
Warm up the engine.
Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and head.
| 24. ADJUST SHIFT LEVER POSITION |
Move the shift lever to the N position.
![]() |
Fold back the transmission control cable adjust case cover. Then while sliding the slider toward the cable end side, press the lock piece from the back side to release the lock.
![]() |
Check that the adjust case's spring is applying enough tension to the shift control cable. Then press the lock piece to set the lock.
Return the cover of the adjust case to its original position.
Inspect the operation after the adjustment.
| 25. INSPECT SHIFT LEVER POSITION |
When moving the shift lever from the N position to other positions, check that the lever can be shifted smoothly and accurately to each position and that the position indicator comes on in accordance with the shift lever position.
If the indicator and shift lever position do not match, carry out the following adjustment procedures.
| 26. INSPECT FOR EXHAUST GAS LEAK |
| 27. INSTALL NO. 1 ENGINE UNDER COVER |
![]() |
Hook the engine under cover to the vehicle body as shown in the illustration.
Install the 3 screws and 5 bolts.
| 28. RESET MEMORY |