STEERING GEAR > INSTALLATION |
| 1. INSTALL POWER STEERING GEAR ASSEMBLY |
![]() |
Install the power steering gear with the 2 bolts and 2 nuts.
| 2. INSTALL PRESSURE FEED TUBE ASSEMBLY |
![]() |
Temporarily connect the pressure feed tube to the power steering gear.
![]() |
Install the pressure feed tube clamp with the 2 bolts.
![]() |
Using a union nut wrench, tighten the pressure feed tube (pressure feed tube side).
![]() |
Using a union nut wrench, tighten the pressure feed tube (return tube side).
| 3. CONNECT TIE ROD END SUB-ASSEMBLY LH |
Connect the tie rod end LH to the steering knuckle with the nut.
Install a new cotter pin.
| 4. CONNECT TIE ROD END SUB-ASSEMBLY RH |
| 5. CONNECT NO. 2 STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY |
![]() |
Align the matchmarks on the No. 2 steering intermediate shaft and power steering gear.
Install the bolt.
| 6. INSTALL ENGINE ASSEMBLY |
for 1GR-FE:
Install the engine assembly (Click here).
for 3UR-FBE:
Install the engine assembly (Click here).
for 1UR-FE:
Install the engine assembly (Click here).
for 3UR-FE:
Install the engine assembly (Click here).
| 7. INSTALL FRONT WHEEL |
| 8. BLEED POWER STEERING FLUID (for 1GR-FE) |
Check the fluid level.
Jack up the front of the vehicle and support it with stands.
Turn the steering wheel.
With the engine stopped, turn the wheel slowly from lock to lock several times.
Lower the vehicle.
Start the engine.
Run the engine at idle for a few minutes.
Turn the steering wheel.
With the engine idling, turn the wheel left or right to the full lock position and keep it there for 2 to 3 seconds, then turn the wheel to the opposite full lock position and keep it there for 2 to 3 seconds.(*1)
Repeat (*1) several times.
Stop the engine.
![]() |
Check for foaming or emulsification.
If the system has to be bled twice because of foaming or emulsification, check for fluid leaks in the system.
Check the fluid level.
| 9. BLEED POWER STEERING FLUID (for 1UR-FE) |
Check the fluid level.
Jack up the front of the vehicle and support it with stands.
Turn the steering wheel.
With the engine stopped, turn the wheel slowly from lock to lock several times.
Lower the vehicle.
Start the engine.
Run the engine at idle for a few minutes.
Turn the steering wheel.
With the engine idling, turn the wheel left or right to the full lock position and keep it there for 2 to 3 seconds, and then turn the wheel to the opposite full lock position and keep it there for 2 to 3 seconds.*1
Repeat *1 several times.
Stop the engine.
![]() |
Check for foaming or emulsification.
If the system has to be bled twice because of foaming or emulsification, check for fluid leaks in the system.
Check the fluid level.
| 10. BLEED POWER STEERING FLUID (for 3UR-FE, 3UR-FBE) |
Check the fluid level.
Jack up the front of the vehicle and support it with stands.
Turn the steering wheel.
With the engine stopped, turn the wheel slowly from lock to lock several times.
Lower the vehicle.
Start the engine.
Run the engine at idle for a few minutes.
Turn the steering wheel.
With the engine idling, turn the wheel left or right to the full lock position and keep it there for 2 to 3 seconds, then turn the wheel to the opposite full lock position and keep it there for 2 to 3 seconds.(*1)
Repeat (*1) several times.
Stop the engine.
![]() |
Check for foaming or emulsification.
If the system has to be bled twice because of foaming or emulsification, check for fluid leaks in the system.
Check the fluid level.
| 11. CHECK POWER STEERING FLUID LEVEL (for 1GR-FE) |
![]() |
Keep the vehicle horizontal.
With the engine stopped, check the fluid level in the reservoir.
If necessary, add fluid.
Start the engine and run it at idle.
Turn the steering wheel from lock to lock several times to raise fluid temperature.
![]() |
Check for foaming or emulsification.
If foaming or emulsification is identified, bleed the power steering system.
![]() |
With the engine idling, measure the fluid level in the reservoir.
Stop the engine.
Wait a few minutes and remeasure the fluid level in the reservoir.
Check the fluid level.
| 12. CHECK POWER STEERING FLUID LEVEL (for 1UR-FE) |
![]() |
Keep the vehicle horizontal.
With the engine stopped, check the fluid level in the reservoir.
If necessary, add fluid.
Start the engine and run it at idle.
Turn the steering wheel from lock to lock several times to raise the fluid temperature.
![]() |
Check for foaming or emulsification.
If foaming or emulsification is identified, bleed the power steering system.
![]() |
With the engine idling, measure the fluid level in the reservoir.
Stop the engine.
Wait a few minutes and remeasure the fluid level in the reservoir.
Check the fluid level.
| 13. CHECK POWER STEERING FLUID LEVEL (for 3UR-FE, 3UR-FBE) |
![]() |
Keep the vehicle horizontal.
With the engine stopped, check the fluid level in the reservoir.
If necessary, add fluid.
Start the engine and run it at idle.
Turn the steering wheel from lock to lock several times to raise the fluid temperature.
![]() |
Check for foaming or emulsification.
If foaming or emulsification is identified, bleed the power steering system.
![]() |
With the engine idling, measure the fluid level in the reservoir.
Stop the engine.
Wait a few minutes and remeasure the fluid level in the reservoir.
Check the fluid level.
| 14. INSPECT FOR POWER STEERING FLUID LEAK |
| 15. PLACE FRONT WHEELS FACING STRAIGHT AHEAD |
| 16. ADJUST FRONT WHEEL ALIGNMENT |
Adjust the front wheel alignment (Click here).