ENGINE ASSEMBLY > INSTALLATION |
| 1. REMOVE ENGINE STAND |
![]() |
Install the 2 engine hangers with the 2 bolts as shown in the illustration.
| Item | Part No. |
| Engine hanger | 12281-38150 |
| Bolt | 90119-A0166 |
Attach an engine sling device and hang the engine with a chain block.
Remove the bolts and engine assembly from the engine stand.
| 2. INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY LH |
![]() |
Install a new gasket to the cylinder head and a new gasket to the No. 3 air tube.
![]() |
Temporarily install the exhaust manifold with the 2 nuts labeled A and 8 new nuts.
Uniformly tighten the nuts that are not labeled A, and then tighten the 2 nuts labeled A.
| 3. INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR |
![]() |
Install the heat insulator with the 3 bolts.
| 4. INSTALL ENGINE ASSEMBLY |
Slowly lower the engine assembly into the engine compartment.
Attach the engine mounting insulators to the vehicle.
![]() |
Install the 4 engine mounting insulator bolts.
Remove the 2 bolts and 2 engine hangers.
| 5. INSTALL NO. 1 WATER BY-PASS PIPE |
![]() |
Connect the hose and install the water by-pass pipe with the 2 bolts.
| 6. INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY |
![]() |
Using SST, hold the crankshaft.
Install the crankshaft angle sensor plate, drive gear and rear drive plate spacer to the crankshaft.
![]() |
Install and uniformly tighten 10 new bolts in the sequence shown in the illustration.
![]() |
Mark the upside of each flywheel installation bolt with paint.
Tighten the flywheel installation bolts another 90° as shown.
Check that the painted marks are now at a 90° angle to the upside.
| 7. INSTALL AUTOMATIC TRANSMISSION ASSEMBLY |
Install the automatic transmission (Click here).
| 8. INSTALL STARTER ASSEMBLY |
![]() |
Install the flywheel housing side cover.
Install the starter with the 2 bolts.
Install the starter wire with the nut.
Connect the starter connector.
Attach the 2 wire harness clamps.
| 9. INSTALL STARTER COVER |
Install the starter cover with the 3 bolts.
| 10. INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY RH |
![]() |
Install a new gasket to the cylinder head and a new gasket to the No. 2 air tube.
![]() |
Temporarily install the exhaust manifold with the 2 nuts labeled A and 8 new nuts.
Uniformly tighten the nuts that are not labeled A, and then tighten the 2 nuts labeled A.
| 11. INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR |
![]() |
Install the heat insulator with the 3 bolts.
| 12. INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE |
Apply a light coat of engine oil to a new O-ring.
![]() |
Install the O-ring to the guide.
Install the dipstick guide with the bolt.
Install the dipstick.
| 13. INSTALL FRONT FENDER APRON SEAL REAR RH |
Install the fender apron seal with the 5 clips.
| 14. INSTALL FRONT FENDER APRON SEAL RH |
Install the fender apron seal with the 6 clips.
| 15. INSTALL FRONT PROPELLER SHAFT ASSEMBLY |
Install the front propeller shaft (Click here).
| 16. INSTALL PROPELLER SHAFT ASSEMBLY |
Install the propeller shaft (Click here).
| 17. INSTALL EXHAUST PIPE ASSEMBLY |
Install the exhaust pipe assembly (Click here).
| 18. INSTALL GENERATOR ASSEMBLY |
![]() |
Install the generator with the 3 bolts and nut.
![]() |
Connect the generator connector.
Connect the generator wire with the nut.
Install the terminal cap.
Install the harness bracket to the generator with the bolt.
| 19. CONNECT VANE PUMP ASSEMBLY |
![]() |
| *a | Spacer |
Connect the vane pump assembly to the timing chain cover sub-assembly with the 2 bolts.
| 20. CONNECT COOLER COMPRESSOR ASSEMBLY |
![]() |
Install the cooler compressor assembly with the 2 stud bolts.
Install the 2 bolts and 2 nuts.
| 21. CONNECT WIRE HARNESS AND HOSE |
![]() |
Connect the 2 connectors and 2 clips to the engine room junction block.
Install the engine wire with the nut. Then connect the 2 clips.
Connect the 4 air injection control driver connectors.
Install the ground wire with the bolt.
Connect the cable to the positive (+) battery terminal.
Install the wire to the positive (+) battery cable with the nut.
![]() |
Connect the 2 air injection system hoses.
Install the ground wire with the bolt.
Connect the 2 air pump connectors and install the connector bracket with the nut.
![]() |
Connect the 4 connectors to the connector holder block.
![]() |
Connect the heater hoses.
Connect the ECM connector and clamp.
![]() |
Connect the union to check valve hose.
Connect the purge line hose.
| 22. CONNECT FUEL MAIN AND RETURN HOSE |
![]() |
Connect the fuel main and return hoses (Click here).
Install the fuel pipe clamp.
| 23. INSTALL RADIATOR ASSEMBLY |
![]() |
Set the radiator bracket hooks to the radiator support holes.
Install the radiator assembly with the 4 bolts.
| 24. INSTALL FAN SHROUD |
Install the fan pulley to the fan bracket.
Place the fan shroud together with the fan with fluid coupling between the radiator assembly and engine.
Temporarily install the fan with fluid coupling to the fan bracket with the 4 nuts. Tighten the nuts as much as possible by hand.
![]() |
Attach the 2 claws of the fan shroud to the radiator assembly as shown in the illustration.
Install the fan shroud with the 2 bolts.
![]() |
for Condenser with Integrated Oil Cooler:
Pass the 2 hoses through the flexible hose clamp and close the clamp as shown in the illustration.
Connect the reservoir hose to the upper radiator tank.
Install the fan and generator V-belt.
![]() |
Tighten the 4 nuts of the fan with fluid coupling.
| 25. INSTALL FAN & GENERATOR V BELT |
![]() |
Set the V belt onto every part.
While turning the belt tensioner counterclockwise, remove the pin.
![]() |
After installing the belt, check that it fits properly in the ribbed grooves.
| 26. INSTALL RADIATOR SIDE DEFLECTOR LH |
Install the 3 clips to connect the radiator side deflector LH.
| 27. INSTALL RADIATOR SIDE DEFLECTOR RH |
Install the 3 clips to connect the radiator side deflector RH.
| 28. INSTALL RADIATOR GRILLE SUB-ASSEMBLY |
Attach the 4 claws and 3 clips to install the radiator grille sub-assembly.
Install the 4 screws and 2 clips.
| 29. INSTALL OUTLET RADIATOR HOSE |
| 30. INSTALL INLET RADIATOR HOSE |
| 31. INSTALL AIR CLEANER ASSEMBLY |
![]() |
Install the air cleaner case with the 2 bolts.
Install the air cleaner element onto the air cleaner case.
![]() |
Install the air cleaner cap.
for Type A:
Install the air cleaner cap and fasten the 4 hook clamps.
for Type B:
Install the air cleaner cap and fasten the 2 hook clamps.
Connect the MAF meter connector.
Attach the wire harness clamp.
| 32. INSTALL AIR CLEANER HOSE ASSEMBLY |
![]() |
Install the air cleaner hose with the 2 clamps.
Connect the vacuum hose.
Connect the ventilation hose.
| 33. ADD ENGINE OIL |
Add fresh oil.
| Oil Grade | Oil Viscosity (SAE) |
| ILSAC GF-5 multigrade engine oil | 0W-20 |
| Item | Specified Condition |
| Drain and refill without oil filter change | 7.1 liters (7.5 US qts, 6.2 Imp. qts) |
| Drain and refill with oil filter change | 7.5 liters (7.9 US qts, 6.6 Imp. qts) |
| Dry fill | 9.3 liters (9.8 US qts, 8.2 Imp. qts) |
Install the oil filler cap.
| 34. ADD ENGINE COOLANT |
Add engine coolant.
| Item | Specified Condition |
| w/ Trailer Towing System | 13.0 liters (13.7 US qts, 11.4 Imp. qts) |
| w/o Trailer Towing System | 12.1 liters (12.8 US qts, 10.6 Imp. qts) |
![]() |
Slowly pour coolant into the radiator reservoir until it reaches the FULL line.
Install the reservoir cap.
Press the inlet and outlet radiator hoses several times by hand, and then check the coolant level. If the coolant level is low, add coolant.
Install the radiator cap.
Start the engine and warm it up until the thermostat opens.
Maintain the engine speed at 2000 to 2500 rpm.
Press the inlet and outlet radiator hoses several times by hand to bleed air.
Stop the engine, and wait until the engine coolant cools down to ambient temperature.
![]() |
Check that the coolant level is between the FULL and LOW lines.
If the coolant level is below the LOW line, repeat all of the procedures above.
If the coolant level is above the FULL line, drain coolant so that the coolant level is between the FULL and LOW lines.
| 35. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 36. INSPECT FOR OIL LEAK |
Inspect for engine oil leak .
| 37. INSPECT FOR COOLANT LEAK |
![]() |
Fill the radiator with coolant and attach a radiator cap tester.
Warm up the engine.
Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and head.
| 38. INSPECT FOR EXHAUST GAS LEAK |
| 39. INSPECT FOR FUEL LEAK |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and Techstream main switch on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.
Check that there are no fuel leaks after doing maintenance anywhere on the fuel system.
| 40. INSPECT SHIFT LEVER POSITION |
for Column Shift:
Refer to the following procedures .
for Floor Shift:
Refer to the following procedures .
| 41. INSTALL V-BANK COVER SUB-ASSEMBLY |
![]() |
Attach the 2 V-bank cover hooks to the bracket. Then align the 2 V-bank cover grommets with the 2 pins, and press down on the V-bank cover to attach the pins.
| 42. INSTALL COWL TOP OUTER PANEL SUB-ASSEMBLY |
Install the cowl top outer panel sub-assembly with the 7 bolts.
Connect the washer hose and attach the 2 wire harness clamps.
| 43. INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY |
Install the windshield wiper motor (Click here).
| 44. INSTALL HOOD SUB-ASSEMBLY |
![]() |
Install the hood with the 4 bolts.
Attach the lower part of the 2 hood supports to the hood support bolt ball joints.
Attach the hood support clips.
| 45. ADJUST HOOD SUB-ASSEMBLY |
![]() |
Adjust the hood sub-assembly position.
Loosen the 4 hinge bolts.
Move the hood sub-assembly and adjust the clearance between the hood sub-assembly and front fender.
Tighten the 4 hinge bolts after the adjustment.
![]() |
Adjust the cushion rubber so that the height of the hood sub-assembly and fender are aligned.
Adjust the hood lock assembly.
![]() |
Using a screwdriver, remove the hood lock nut cap as shown in the illustration.
| *1 | Protective Tape |
![]() |
Loosen the 2 bolts and hood lock bolt.
Adjust the hood lock assembly position so that the striker can enter it smoothly.
Tighten the bolts after the adjustment.
Install a new hood lock nut cap.
| 46. INSTALL NO. 1 ENGINE UNDER COVER |
![]() |
Hook the engine under cover to the vehicle body as shown in the illustration.
Install the 3 screws and 5 bolts.
| 47. INSPECT IGNITION TIMING |
Warm up and stop the engine.
Allow the engine to warm up to a normal operating temperature.
When using the Techstream:
Connect the Techstream to the DLC3.
Start the engine and idle it.
Turn the Techstream main switch ON.
Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / IGN Advance.
Disconnect the Techstream from the DLC3.
![]() |
When not using the Techstream:
Connect the tester probe of a timing light to the wire of the ignition coil connector for the No. 1 cylinder.
![]() |
Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
![]() |
Using the timing light, check the ignition timing.
Remove SST from the DLC3.
Check the ignition timing.
Disconnect the timing light from the engine.
| 48. INSPECT ENGINE IDLE SPEED |
Warm up and stop the engine.
Allow the engine to warm up to a normal operating temperature.
When using the Techstream:
Connect the Techstream to the DLC3.
Race the engine at 2500 rpm for approximately 90 seconds.
Turn the Techstream main switch ON.
Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Engine Speed.
Disconnect the Techstream from the DLC3.
![]() |
When not using the Techstream:
Using SST, connect the tachometer probe to terminal 9 (TAC) of the DLC3.
Race the engine at 2500 rpm for approximately 90 seconds.
Check the idle speed.
Disconnect the tachometer probe from the DLC3.
| 49. INSPECT CO/HC |
Start the engine.
Keep the engine speed at 2500 rpm for approximately 180 seconds.
![]() |
Insert the CO/HC meter testing probe at least 40 cm (1.31 ft.) into the tailpipe during idling.
Immediately check CO/HC concentration at idle and/or 2500 rpm.
If the CO/HC concentration does not comply with the regulations, troubleshoot in the order given below.
Check the A/F sensor operation (Click here) and heated oxygen sensor operation (Click here).
See the table below for possible causes, and then inspect and correct the applicable causes if necessary.
| CO | HC | Symptom | Cause |
| Normal | High | Rough idle |
|
| Low | High | Rough idle (Fluctuating HC reading) |
|
| High | High | Rough idle (Black smoke from exhaust) |
|
| 50. CHECK ENGINE OIL LEVEL |
Warm up the engine, then stop the engine and wait for 5 minutes.
Check that the engine oil level is between the low level and full level marks on the dipstick.
If low, check for leakage and add oil up to the full level mark.
| 51. CHECK ENGINE COOLANT LEVEL |
![]() |
Check that the engine coolant level is between the LOW and FULL lines when the engine is cold.
If the engine coolant is low, check for leaks and add "TOYOTA Super Long Life Coolant" or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite and non-borate coolant with long-life hybrid organic acid technology to the FULL line.