Home › ENGINE ยท 1UR-FE › ENGINE MECHANICAL › ENGINE ASSEMBLY

ENGINE ASSEMBLY > INSTALLATION

for Preparation Click here


HINT:
Perform "Inspection After Repairs" after replacing the engine assembly, cylinder head sub-assembly RH, cylinder head sub-assembly LH, No. 1 camshaft sub-assembly, No. 2 camshaft sub-assembly, No. 3 camshaft sub-assembly, No. 4 camshaft sub-assembly, camshaft timing gear RH, camshaft timing gear LH, camshaft timing exhaust gear RH, camshaft timing exhaust gear LH, piston or piston ring (Click here).



1. REMOVE ENGINE FROM ENGINE STAND


    A217476
  1. Install the 2 engine hangers with the 2 bolts as shown in the illustration.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }

    HINT:
    Engine hanger
    12281-38150
    Bolt
    90119-A0166

  1. Attach an engine sling device and hang the engine with a chain block.

  1. Remove the bolts and engine assembly from the engine stand.



2. INSTALL ENGINE ASSEMBLY
  1. Slowly lower the engine assembly into the engine compartment.

    NOTICE:
    Make sure that the engine is clear of all wiring and hoses.

  1. Attach the engine mounting insulators to the vehicle.



    A214577E01
  1. Install the 4 engine mounting insulator bolts.

    Torque:
    79 N*m{ 806 kgf*cm , 58 ft.*lbf }

  1. Remove the 2 bolts and 2 engine hangers.



3. INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY


    A163778E01
  1. Using SST, hold the crankshaft.

    SST
    09213-70011  
    09330-00021  



    A217514E01
  1. Install the crankshaft angle sensor rotor.

    HINT:
    Align the pin hole of the crankshaft angle sensor rotor with the pin of the crankshaft.



    A217515E01
  1. Install the drive plate and rear drive plate spacer onto the crankshaft.



    A057108E09
  1. Apply adhesive to 2 or 3 threads of the 8 bolts.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



    A214574E01
  1. Install and uniformly tighten 10 new bolts in the sequence shown in the illustration.

    Torque:
    30 N*m{ 301 kgf*cm , 22 ft.*lbf }

    NOTICE:
    1. Do not reuse the drive plate installation bolts.
    2. Do not strike or damage the drive plate installation bolts. Be sure to handle them carefully.



    A149106E01
  1. Mark the top of each drive plate installation bolt with paint.

  1. Tighten the drive plate installation bolts 90° as shown in the illustration.

  1. Check that the painted marks are now at a 90° angle to the top.



4. INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR (for 4WD)
  1. Install the rear engine mounting insulator to the transmission with the 4 bolts.

    Torque:
    59 N*m{ 602 kgf*cm , 44 ft.*lbf }



5. INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR (for 2WD)
  1. Install the rear engine mounting insulator to the transmission with the 4 bolts.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



6. INSTALL AUTOMATIC TRANSMISSION ASSEMBLY
  1. for 2WD:
    Refer to the following procedures (Click here).

  1. for 4WD:
    Refer to the following procedures (Click here).



7. INSTALL STARTER ASSEMBLY
  1. Install the flywheel housing side cover.

  1. Install the starter with the 2 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

  1. Connect the starter wire with the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Connect the starter connector.

  1. Attach the 2 wire harness clamps.



8. INSTALL STARTER COVER
  1. Install the starter cover with the 3 bolts.

    Torque:
    12 N*m{ 117 kgf*cm , 8 ft.*lbf }



9. INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY RH


    A215352E01
  1. Install a new gasket to the cylinder head and a new gasket to the No. 3 air tube.

    HINT:
    1. Install the exhaust manifold gasket with the gasket tab facing toward the front of the engine.
    2. Install the air tube gasket with the gasket's claws facing the tube.



    A215351E01
  1. Temporarily install the exhaust manifold with 9 new nuts, and then uniformly tighten the 7 nuts that are not labeled A. Then tighten the 2 nuts labeled A in the illustration.

    Torque:
    for nut A:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }
    except nut A:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



10. INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR


    A215350
  1. Install the heat insulator with the 3 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



11. INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY LH


    A215353E01
  1. Install a new gasket to the cylinder head and a new gasket to the No. 4 air tube.

    HINT:
    1. Install the exhaust manifold gasket with the gasket tab facing toward the rear of the engine.
    2. Install the air tube gasket with the gasket's claws facing the tube.



    A215349E01
  1. Temporarily install the exhaust manifold with 9 new nuts, and then uniformly tighten the 7 nuts that are not labeled A. Then tighten the 2 nuts labeled A in the illustration.

    Torque:
    for nut A:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }
    except nut A:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



12. INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR


    A215348
  1. Install the heat insulator with the 3 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



13. INSTALL NO. 1 EGR PIPE SUB-ASSEMBLY
  1. Install 2 new gaskets.



    A214293E01
  1. Install the EGR pipe with the 4 nuts, and tighten the nuts in the sequence shown in the illustration.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



14. INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE
  1. Apply a light coat of engine oil to a new O-ring.

  1. Install the O-ring to the dipstick guide.



    A216301
  1. Install the dipstick guide with the bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Install the dipstick.



15. CONNECT NO. 1 WATER BY-PASS PIPE


    A214575
  1. Connect the No. 1 water by-pass pipe with the 3 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



16. INSTALL EXHAUST PIPE ASSEMBLY
  1. Install the exhaust pipe assembly (Click here).



17. INSTALL FRONT PROPELLER SHAFT ASSEMBLY (for 4WD)
  1. Install the front propeller shaft (Click here).



18. INSTALL PROPELLER SHAFT ASSEMBLY
  1. for 2WD:
    Refer to the following procedures (Click here).

  1. for 4WD:
    Refer to the following procedures (Click here).



19. INSTALL GENERATOR ASSEMBLY


    A216790
  1. Install the generator with the 3 bolts and nut.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }



    A215539
  1. Install the harness bracket to the generator with the bolt.

    Torque:
    31 N*m{ 316 kgf*cm , 23 ft.*lbf }

  1. Connect the generator connector.

  1. Connect the generator wire with the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Install the terminal cap.



20. CONNECT VANE PUMP ASSEMBLY


A163333E05
  1. Connect the vane pump assembly to the timing chain cover sub-assembly with the 2 bolts.

    Torque:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }

    Text in Illustration 
    *a
    Spacer

    HINT:
    Before performing the following procedures, move the spacer until the vane pump assembly can be installed.



21. CONNECT COOLER COMPRESSOR ASSEMBLY


    A163332E01
  1. Connect the cooler compressor assembly with the 2 stud bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Install the 2 bolts and 2 nuts.

    Torque:
    25 N*m{ 250 kgf*cm , 18 ft.*lbf }

    NOTICE:
    Tighten the bolts and nuts in the order shown in the illustration to connect the cooler compressor assembly.



22. CONNECT WIRE HARNESS AND HOSE


    A163790
  1. Connect the 2 connectors and 2 clips to the engine room junction block.

  1. Install the engine wire with the nut. Then connect the 2 clips.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Connect the 4 air injection control driver connectors.

  1. Install the ground wire with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the cable to the positive (+) battery terminal.

  1. Install the wire to the positive (+) battery cable with the nut.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }



    A214573
  1. Connect the air injection system hose.

  1. Install the connector bracket with the nut.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }

  1. Connect the 2 clamps and air pump connector.

  1. Connect the clamp and ground wire with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



    A160782E01
  1. Connect the 4 connectors to the connector holder block.



    A214851
  1. Connect the 2 heater hoses.



    A214858
  1. Connect the No. 4 water by-pass hose.



    A214862
  1. Connect the ECM connector and clamp.

    HINT:
    Refer to the following procedures to connect the ECM connector .



23. CONNECT NO. 2 FUEL TUBE SUB-ASSEMBLY
  1. Connect the No. 2 fuel tube (Click here).



24. CONNECT NO. 1 FUEL PIPE SUB-ASSEMBLY


    A308865
  1. Connect the No. 1 fuel pipe (Click here).

  1. Install the fuel pipe clamp.



25. INSTALL INTAKE MANIFOLD


    A215297
  1. Place 2 new gaskets on the intake manifold.

  1. Place the intake manifold on the cylinder head sub-assembly.

  1. Install and uniformly tighten the 8 bolts and 2 nuts in several steps.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Connect the fuel tube sub-assembly to the fuel delivery pipe sub-assembly LH (Click here).

  1. Connect the fuel tube sub-assembly to the fuel delivery pipe sub-assembly RH (Click here).

  1. Attach the 4 clamps to the fuel tube sub-assembly.

  1. Attach the 3 engine wire harness clamps to the 3 wire harness brackets.

  1. Install the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the vacuum hose to the union to connector tube hose assembly, and slide the clamp to secure the hose.

  1. Connect the purge line hose to the purge VSV, and slide the clamp to secure the hose.

  1. Connect the 2 vacuum switching valve connectors.

  1. Connect the ventilation hose to the intake manifold, and slide the clamp to secure the hose.

  1. Connect the No. 4 water by-pass hose to the front water by-pass joint, and slide the clamp to secure the hose.

  1. Connect the throttle body connector to the throttle body assembly.



26. INSTALL AIR TUBE SUB-ASSEMBLY LH


    A215284
  1. Connect the air hose to the air switching valve LH, and install the air tube LH with the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Connect the vacuum sensor connector and clamp.



    A217630E01
  1. Connect the air tube LH to the water inlet housing with the bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Connect the air hose.

  1. Connect the 2 wire harness clamps.

    HINT:
    When installing the hose, make sure the paint mark and clip are as shown in the illustration.



    A215880E01
  1. Connect the water by-pass hose and 2 connectors.

    HINT:
    When installing the hose, make sure the paint mark and clip are as shown in the illustration.



27. INSTALL VENTILATION HOSE ASSEMBLY
  1. Install the ventilation hose assembly with the bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Connect the ventilation hose assembly to the ventilation pipe of the cylinder head cover sub-assembly LH and cylinder head cover sub-assembly RH, and slide the 2 clamps to secure the hose.



28. INSTALL EGR VALVE BRACKET


    A214283
  1. Install the EGR valve bracket with the 3 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



29. INSTALL EGR VALVE ASSEMBLY


    A214282
  1. Install a new gasket to the intake manifold.



    A214876
  1. Install a new gasket to the No. 2 EGR pipe.



    A214286
  1. Temporarily install the EGR valve assembly to the intake manifold with the 2 bolts and 4 nuts.

    NOTICE:
    Be careful not to damage the intake manifold when installing the EGR valve assembly.



    A214286E01
  1. Using several steps, uniformly tighten the 2 bolts and 4 nuts in the sequence shown in the illustration.

    Torque:
    for bolt:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }
    for nut:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



30. CONNECT NO. 13 WATER BY-PASS HOSE


    A214276E01
  1. Connect the No. 13 water by-pass hose.

    HINT:
    The direction of the hose clamp is indicated in the illustration.



31. CONNECT NO. 12 WATER BY-PASS HOSE


    A214278E01
  1. Connect the No. 12 water by-pass hose.

    HINT:
    The direction of the hose clamp is indicated in the illustration.



32. INSTALL RADIATOR ASSEMBLY
  1. Install a new O-ring to the radiator drain cock plug.

  1. Install the radiator drain cock plug to the radiator assembly.



    A218981E01
  1. Install the outlet radiator hose to the radiator assembly, and slide the clamp to secure the hose.

    HINT:
    Install the hose so that the direction of the hose clamp is as indicated in the illustration.



    A299480
  1. Set the radiator bracket hooks to the radiator support holes.

  1. Install the radiator assembly with the 4 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



33. INSTALL FAN SHROUD
  1. Install the fan pulley to the fan bracket.

  1. Place the fan shroud together with the fluid coupling fan between the radiator and engine.

    NOTICE:
    Be careful not to damage the radiator core

  1. Temporarily install the fluid coupling fan to the fan bracket with the 4 nuts. Tighten the nuts as much as possible by hand.



    A215576
  1. Attach the shroud's claws to the radiator as shown in the illustration.

  1. Install the shroud with the 2 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }

  1. Connect the reservoir hose to the upper radiator tank.

  1. Install the fan and generator V-belt (Click here).



    A217580
  1. Tighten the 4 nuts of the fluid coupling fan.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



34. INSTALL FAN AND GENERATOR V BELT


    A217532E01
  1. Set the V belt onto every part.

  1. While turning the belt tensioner counterclockwise, remove the pin.

    NOTICE:
    Make sure that the V belt is properly set to each pulley.



    A174124E01
  1. After installing the belt, check that it fits properly in the ribbed grooves.

    HINT:
    Make sure to check by hand that the belt has not slipped out of the grooves on the bottom of the pulley.



35. INSTALL RADIATOR SIDE DEFLECTOR LH
  1. Install the 3 clips to connect the radiator side deflector LH.



36. INSTALL RADIATOR SIDE DEFLECTOR RH
  1. Install the 3 clips to connect the radiator side deflector RH.



37. INSTALL RADIATOR GRILLE SUB-ASSEMBLY
  1. Attach the 4 claws and 3 clips to install the radiator grille sub-assembly.

  1. Install the 4 screws and 2 clips.

    Torque:
    3.0 N*m{ 31 kgf*cm , 27 in.*lbf }



38. CONNECT OUTLET RADIATOR HOSE


    A217244E01
  1. Connect the radiator hose.

    HINT:
    The direction of hose clamp is indicated in the illustration.



39. INSTALL INLET RADIATOR HOSE


    A215578E01
  1. Install the inlet radiator hose.

    HINT:
    The direction of each hose clamp is indicated in the illustration.



40. INSTALL FRONT FENDER APRON SEAL REAR LH
  1. Install the fender apron seal with the 5 clips.



41. INSTALL FRONT FENDER APRON SEAL LH
  1. Install the fender apron seal with the 6 clips.



42. INSTALL FRONT FENDER APRON SEAL REAR RH
  1. Install the fender apron seal with the 5 clips.



43. INSTALL FRONT FENDER APRON SEAL RH
  1. Install the fender apron seal with the 6 clips.



44. INSTALL COWL TOP OUTER PANEL SUB-ASSEMBLY
  1. Install the cowl top outer panel sub-assembly with the 7 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Connect the washer hose and attach the 2 wire harness clamps.



45. INSTALL AIR CLEANER ASSEMBLY


    A309638E01
  1. Install the air cleaner case with the 2 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Install the air cleaner element to the air cleaner case.



    A309637E01
  1. Install the air cleaner cap.

    1. for Type A:
      Install the air cleaner cap and fasten the 4 hook clamps.

    2. for Type B:
      Install the air cleaner cap and fasten the 2 hook clamps.

    3. Connect the MAF meter connector.

    4. Attach the wire harness clamp.



46. INSTALL AIR CLEANER HOSE ASSEMBLY


    A214569
  1. Install the air cleaner hose with the 2 clamps.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }

  1. Connect the ventilation hose and vacuum sensing hose.



47. ADD ENGINE OIL
  1. Add fresh oil.

    Standard Oil Grade:
    Oil Grade
    Oil Viscosity (SAE)
    ILSAC GF-5 multigrade engine oil
    0W-20

    Standard Oil Capacity:
    Item
    Specified Condition
    Drain and refill without oil filter change
    7.1 liters (7.5 US qts, 6.2 Imp. qts)
    Drain and refill with oil filter change
    7.5 liters (7.9 US qts, 6.6 Imp. qts)
    Dry fill
    9.3 liters (9.8 US qts, 8.2 Imp. qts)

  1. Install the oil filler cap.



48. ADD ENGINE COOLANT
  1. Add engine coolant.

    Standard capacity:
    12.1 liters (12.8 US qts, 10.6 Imp. qts)

    NOTICE:
    Do not substitute plain water for engine coolant.

    HINT:
    TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology is a combination of low phosphates and organic acids).



    A151850E05
  1. Slowly pour coolant into the radiator reservoir until it reaches the FULL line.

  1. Install the reservoir cap.

  1. Press the inlet and outlet radiator hoses several times by hand, and then check the coolant level. If the coolant level is low, add coolant.

  1. Install the radiator cap.

  1. Start the engine and warm it up until the thermostat opens.

    HINT:
    The thermostat opening timing can be confirmed by pressing the radiator inlet hose by hand, and checking when the engine coolant starts to flow inside the hose.

  1. Maintain the engine speed at 2000 to 2500 rpm.

    NOTICE:
    1. Make sure that the radiator reservoir still has some coolant in it.
    2. Pay attention to the needle of the water temperature meter. Make sure that the needle does not show an abnormally high temperature.
    3. If there is not enough coolant, the engine may burn out or overheat.
    4. Immediately after starting the engine, if the radiator reservoir does not have any coolant, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the coolant is filled to the FULL line.
    5. Run the engine at 2000 rpm until the coolant level has stabilized.

  1. Press the inlet and outlet radiator hoses several times by hand to bleed air.

    CAUTION:
    1. Wear protective gloves.
    2. Be careful as the radiator hoses are hot.
    3. Keep your hands away from the fan.

  1. Stop the engine, and wait until the engine coolant cools down to ambient temperature.

    CAUTION:
    Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.



    A161780E01
  1. Check that the coolant level is between the FULL and LOW lines.
    If the coolant level is below the LOW line, repeat all of the procedures above.
    If the coolant level is above the FULL line, drain coolant so that the coolant level is between the FULL and LOW lines.



49. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL


50. INSPECT FOR OIL LEAK
  1. Start the engine. Make sure that there are no oil leaks from the area that was worked on.



51. INSPECT FOR COOLANT LEAK


A215893

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Fill the radiator with coolant and attach a radiator cap tester.

  1. Warm up the engine.

  1. Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and head.



52. INSPECT FOR EXHAUST GAS LEAK

HINT:
If an exhaust gas leak has been repaired, perform an inspection following the repair (Click here).

If gas is leaking, tighten the areas necessary to stop the leak. Replace damaged parts as necessary.


53. INSPECT FOR FUEL LEAK
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and Techstream main switch on.

    NOTICE:
    Do not start the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

  1. Check that there are no fuel leaks after doing maintenance anywhere on the fuel system.



54. INSPECT SHIFT LEVER POSITION
  1. for Column Shift:
    Refer to the following procedures .

  1. for Floor Shift:
    Refer to the following procedures .



55. INSTALL V-BANK COVER SUB-ASSEMBLY


    A214821E01
  1. Attach the 2 V-bank cover hooks to the bracket. Then align the 2 V-bank cover grommets with the 2 pins, and press down on the V-bank cover to attach the pins.



56. INSTALL HOOD SUB-ASSEMBLY


    A308967
  1. Install the hood with the 4 bolts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

  1. Attach the lower part of the 2 hood supports to the hood support bolt ball joints.

    CAUTION:
    Install the hood support while supporting the hood by hand.

  1. Attach the hood support clips.

    NOTICE:
    Check that the hood support is engaged in the ball joint and that it cannot be pulled out.



57. ADJUST HOOD SUB-ASSEMBLY


    B166027
  1. Adjust the hood sub-assembly position.

    1. Loosen the 4 hinge bolts.

    2. Move the hood sub-assembly and adjust the clearance between the hood sub-assembly and front fender.

    3. Tighten the 4 hinge bolts after the adjustment.

      Torque:
      13 N*m{ 133 kgf*cm , 10 ft.*lbf }



    4. B166028
    5. Adjust the cushion rubber so that the height of the hood sub-assembly and fender are aligned.

      HINT:
      Raise or lower the hood sub-assembly front end by turning the cushion rubber.



  1. Adjust the hood lock assembly.



      B354830E01
    1. Using a screwdriver, remove the hood lock nut cap as shown in the illustration.

      HINT:
      Tape the screwdriver tip before use.

      Text in Illustration 
      *1
      Protective Tape



    2. B354831
    3. Loosen the 2 bolts and hood lock bolt.

    4. Adjust the hood lock assembly position so that the striker can enter it smoothly.

    5. Tighten the bolts after the adjustment.

      Torque:
      8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    6. Install a new hood lock nut cap.



58. INSTALL NO. 1 ENGINE UNDER COVER


    A150108
  1. Hook the engine under cover to the vehicle body as shown in the illustration.

  1. Install the 3 screws and 5 bolts.

    Torque:
    for bolt:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }
    for screw:
    3.0 N*m{ 31 kgf*cm , 27 in.*lbf }



59. INSTALL FRONT WIPER MOTOR AND LINK ASSEMBLY
  1. Install the front wiper motor and link (Click here).



60. INSPECT IGNITION TIMING
  1. Warm up and stop the engine.

    1. Allow the engine to warm up to a normal operating temperature.

  1. When using the Techstream:

    1. Connect the Techstream to the DLC3.

    2. Start the engine and idle it.

    3. Turn the Techstream main switch ON.

    4. Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / IGN Advance.

      HINT:
      Refer to the Techstream operator's manual for further details.

      Standard ignition timing:
      7 to 24° BTDC @ idle (transmission in neutral and A/C switch OFF)

    5. Disconnect the Techstream from the DLC3.



    A308793
  1. When not using the Techstream:

    1. Connect the tester probe of a timing light to the wire of the ignition coil connector for the No. 1 cylinder.

      NOTICE:
      Use a timing light that detects primary signals.



    2. H102392E79
    3. Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

      SST
      09843-18040  

      NOTICE:
      1. Confirm the terminal numbers before connecting them. Connecting the wrong terminals can damage the engine.
      2. Switch off all accessories and the A/C before connecting the terminals.



    4. A218635
    5. Using the timing light, check the ignition timing.

      Standard ignition timing:
      8 to 12° BTDC @ idle (transmission in neutral and A/C switch OFF)

    6. Remove SST from the DLC3.

    7. Check the ignition timing.

      Standard ignition timing:
      7 to 24° BTDC @ idle (transmission in neutral and A/C switch OFF)

    8. Disconnect the timing light from the engine.



61. INSPECT ENGINE IDLE SPEED
  1. Warm up and stop the engine.

    1. Allow the engine to warm up to a normal operating temperature.

  1. When using the Techstream:

    1. Connect the Techstream to the DLC3.

      NOTICE:
      Switch off all accessories and the A/C before connecting the Techstream.

    2. Race the engine at 2500 rpm for approximately 90 seconds.

    3. Turn the Techstream main switch ON.

    4. Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Engine Speed.

      Standard idle speed:
      650 to 750 rpm (transmission in neutral and A/C switch OFF)

      HINT:
      Refer to the Techstream operator's manual for further details.

      If the idle speed is not as specified, check the air intake system.

    5. Disconnect the Techstream from the DLC3.



    H102392E88
  1. When not using the Techstream:

    1. Using SST, connect the tachometer probe to terminal 9 (TAC) of the DLC3.

      SST
      09843-18030  

      NOTICE:
      1. Confirm the terminal number before connecting the probe. Connecting the probe to the wrong terminal can damage the engine.
      2. Switch off all accessories and the A/C before connecting the probe.

    2. Race the engine at 2500 rpm for approximately 90 seconds.

    3. Check the idle speed.

      Standard idle speed:
      650 to 750 rpm (transmission in neutral and A/C switch OFF)

      If the idle speed is not as specified, check the air intake system.

    4. Disconnect the tachometer probe from the DLC3.



62. INSPECT CO/HC

HINT:
This check is used only to determine whether or not the idle CO/ HC complies with regulations.

  1. Start the engine.

  1. Keep the engine speed at 2500 rpm for approximately 180 seconds.



    A150141E01
  1. Insert the CO/HC meter testing probe at least 40 cm (1.31 ft.) into the tailpipe during idling.

  1. Immediately check CO/HC concentration at idle and/or 2500 rpm.

    HINT:
    When performing the 2 mode (2500 rpm and idle) test, follow the measurement order prescribed by the applicable local regulations.

  1. If the CO/HC concentration does not comply with the regulations, troubleshoot in the order given below.

    1. Check the A/F sensor operation (Click here) and heated oxygen sensor operation (Click here).

    2. See the table below for possible causes, and then inspect and correct the applicable causes if necessary.

      CO
      HC
      Symptom
      Cause
      Normal
      High
      Rough idle
      1. Faulty ignitions:
        1. Incorrect timing
        2. Plugs (contaminated, shorted or gaps are defective)
      2. Incorrect valve clearance
      3. Leaky intake and exhaust valves
      4. Leaky cylinder
      Low
      High
      Rough idle
      (Fluctuating HC reading)
      1. Vacuum leaks:
        1. PCV hose
        2. Intake manifold
        3. Throttle body
        4. Brake booster line
      2. Lean mixture causing misfire
      High
      High
      Rough idle
      (Black smoke from exhaust)
      1. Restricted air filter
      2. Faulty SFI system:
        1. Faulty pressure regulator
        2. Defective ECT sensor
        3. Faulty ECM
        4. Faulty injectors
        5. Faulty throttle position sensor
        6. Faulty MAF meter



63. CHECK ENGINE OIL LEVEL
  1. Warm up the engine, then stop the engine and wait for 5 minutes.

  1. Check that the engine oil level is between the low level and full level marks on the dipstick.
    If low, check for leakage and add oil up to the full level mark.

    NOTICE:
    Do not fill engine oil above the full level mark.

    HINT:
    A certain amount of engine oil will be consumed while driving. In the following situations, oil consumption may increase, and engine oil may need to be refilled in between oil maintenance intervals.
    1. When the engine is new, for example directly after purchasing the vehicle or after replacing the engine.
    2. If low quality oil or oil of an inappropriate viscosity is used.
    3. When driving at high engine speed or with a heavy load, (when towing, or), when driving while accelerating or decelerating frequently.
    4. When leaving the idling for a long time, or when driving frequently through heavy traffic.
    When judging the amount of oil consumption, keep in mind that the oil may have become diluted, making it difficult to judge the true level accurately.



64. CHECK ENGINE COOLANT LEVEL


    A151850E05
  1. Check that the engine coolant level is between the LOW and FULL lines when the engine is cold.
    If the engine coolant is low, check for leaks and add "TOYOTA Super Long Life Coolant" or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite and non-borate coolant with long-life hybrid organic acid technology to the FULL line.

    NOTICE:
    Do not substitute plain water for engine coolant.